Conair WW346Z Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Conair WW346Z (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
D I G I TA L B M I
P R E C I S I O N S C A L E
body analysis
results
user
memory
weigh up
to 400 lbs.
Instructions for Use
To get the greatest benefit from your purchase,
please read this entire brochure before using your scale.
WW346Z
Before Using Scale
1. Remove all packaging materials.
2. Remove the isolator tab from the battery compartment – without opening the
battery cover at the bottom of the scale, gently pull out the isolator tab. In case the
tab cannot be pulled out, if it does not completely pull out, or if the display does not
light up when you tap the scale, remove the screw from the battery cover, remove
the cover and gently pull out the isolator tab. Ensure the batteries are installed
correctly and then replace the battery cover and tighten the screw.
3. The Scale is set up to measure weight in pounds. To change the display to
kilograms, press the lb – kg switch underneath the scale when the display is on.
4. For best accuracy, place scale on tile or hardwood floor, rather than uneven,
flexible or soft flooring (such as carpet).
Using the Weight Only Mode
Instructions for customizing your WW BMI Scale are provided. However, the scale
does not need to be programmed to operate as a simple weight scale.
1. Tap the scale with your foot to turn it on. The display will light up.
2. Wait until all digits light for several seconds and “0.0” appears.
3. Step on the scale and stand still to measure your weight. The display will blink
and then shows your weight.
4. The weight reading stays lit for several seconds. Then the scale will shut
off automatically.
Setting Up Your Scale To Calculate BMI
This scale can be customized for up to 4 users. While the customization process is
not difficult, it may be easiest to read all the instructions first to familiarize yourself
with them. Then keep the instruction manual handy as you go through the process
step by step.
Buttons: USER, SET, Up and Down arrows
To set your user data
Tap the scale to turn it on and wait until “0.0” appears.
Setting the user number
Press the “SET” button. The number “P-1” will appear and blink. Use the Up/Down
button to select a user number (P-1 to P-4). Press SET to confirm.
Setting the height
Next, the inch or cm symbol lights up (if switch is set to lb, default is height in inches;
if switch is set to kg, default is height in cm). Press the up or down arrows to adjust
the height. Pressing and holding either the up or the down arrow will advance
numbers quickly. Press SET to accept the height.
Press the SET button again to finish set-up. The scale will display your user data for
a few moments.
Once the scale display shows 0.0 again, the scale is ready to calculate your BMI.
Or, you can let the scale display turn off automatically after several seconds.
BMI Mode
1. Operate the scale on a secure flat floor. Tap the scale to turn it on, and wait until
“0.0” appears. Press the USER button repeatedly until your user number shows on
the display.
2. Stored data for your user number appears (User number, and Height) then the
scale displays “0.0”.
3. Step on the scale and stand still. The Display will flash slowly.


Product specificaties

Merk: Conair
Categorie: Niet gecategoriseerd
Model: WW346Z

Heb je hulp nodig?

Als je hulp nodig hebt met Conair WW346Z stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Conair

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd