Compustar KP2 Handleiding

Bekijk gratis de handleiding van Compustar KP2 (2 pagina’s), behorend tot de categorie Afstandsbediening. Deze gids werd als nuttig beoordeeld door 47 mensen en kreeg gemiddeld 4.1 sterren uit 7 reviews. Heb je een vraag over Compustar KP2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

engine back OFF, close the driver’s side door, and re-attempt steps

#1 through #5.

Via DroneMobile App

If your KP-2 touchpad module is installed with a Drone KL1 KeyLocker

system, you can now manage your passcode(s) from the DroneMobile

App. Please visit https://help.dronemobile.com and search “KP2”.

KP-2 User Guide (Arming + Disarming)

Arm/Lock - To arm and lock your vehicle’s doors, hold down

the LOCK button for 2.5 seconds - do not press any number.

One chirp/honk and One parking light flash will confirming

lock/arm.

Disarm/Unlock - To disarm and unlock your vehicle’s doors,

hold down the LOCK button for 2.5 seconds, then enter your

passcode. NOTE: please press each digit firmly and pause for 1

seconds for two chirps/honks and two parking light flashes,

confirming unlock.

Compatibility (ENGLISH)

CM-X, CM7 Series, and CM-DC3 (Make sure firmware is updated)

Connect to the controller RPS port (white 4-pin).

ȗ-X: ature Option 3-16 to Setting 2 (KP2), 4-15 for sensitivity. Fe

ȗǚǽFeature Option 3-16 to Setting 2 (KP2), 4-15 for sensitivity.

ȗǚǖǓǓǽFeature Option 3-16 to Setting 2 (KP2).

ȗȐǖǽ$($ted Operation

ȐǜǓǓǼȐǜǓǓǼ)ǕǗǓǓșke sure firmware is updated)

Connect to the controller UART port (gray 4-pin), using ‘ANT-Adapt-

er-KP2’ (included in kit).

ȗǜǓǓ/AS: ature Option 4-11 to Setting 3 (KP2), 4-15 for Fe

sensitivity.

ȗǕǗǓǓǽ +/$*)ǖȐǓǔ//$)"ǕșǕȚǼǖȐǓǖFeaturto Sefor

sensitivity.

Mounting & Installation

1) The KP2 touchpad module should be mounted on the front

windshield on the interior, driver’s side. Thoroughly clean and dry the

intended surface.

2) Connect the 4-pin harness prior to mounting.

3) Remove the protective film on the KP2 touchpad module, exposing

the adhesive.

4) Firmly adhere the KP2 touchpad module to the interior of the

windshield at your desired placement. Hold the module in place for

ǖǓ. conds.

KP2 Programming and Passcode Reset

Via Touchpad Module

1) Using your vehicle’s key, turn the ignition to the ON position. You do

not need to start the engine. Then, open the driver’s side door and

leave it open.

2) Press and hold the LOCK button the KP2 touchpad module for 2.5

seconds.

3) If your system has a siren, it will lightly chirp and the red LED will

blink, indicating programming mode.

4) Firmly tap in the first digit of your new passcode. The LED will blink

green when input is received, and then red (with siren chirp) when it

is safe to enter the next digit. Repeat this process until you have

entered all 4/6 digits.

5) Once you have entered all of the digits, please wait until you hear

another siren chirp and see a single parking light flash. This indicates

that programming was complete and successful.

a) If programming is incomplete and/or fails, you will receive three

siren chirps and three parking light flashes. If this occurs, turn your

Compatibilité (FRANÇAIS)

CM-X, CM7 Series, et CM-DC3 (assurezous que le micrologiciel est mis à -v

jour)

Connecter au port RPS du contrôleur (blanc à quatre broches).

ȗ-X : Option de fonction 3-16 au glage 2 (KP2), 4-15 pour la ré

sensibilité.

ȗǚǽ+/$*) fonction 3-16 au glage 2 (KP2), 4-15 pour la ré

sensibilité.

ȗǚǖǓǓǽ+/$*) fonction 3-16 au glage 2 (KP2).ré

ȗȐǖǽFonctionnement limité

ȐǜǓǓǼȐǜǓǓǼ/ǕǗǓǓș..0erez-vous que le micrologiciel est mis

à jour)

Connectezous au port UART du contrôleur (gris à quatre broches), en -v

utilisant 'ANT-Adapter-KP2' (inclus dans le trousse).

ȗǜǓǓ/AS : Option de fonction 4-11 au glage 3 (KP2), 4-15 ré

pour la sensibilité.

ȗǕǗǓǓǽ+/$*) *)/$*)ǖȐǓǔ0 ǕșǕȚǼǖȐǓǖ+*0-'fréglag

sensibilité.

Montage et installation

1) Le module du pavé tactile KP-2 doit être monté sur le pare-brise

Programming &

Operation Manual

CM-900

CM-900AS

CM2400

CM-X

CM7 Series

CM-DC3

White

Gray

(ANT-Adapter-KP2)

Red LED

Green LED

Product specificaties