Chuango SPS-260 Handleiding

Chuango Alarmsysteem SPS-260

Lees hieronder de 📖 handleiding in het Nederlandse voor Chuango SPS-260 (4 pagina's) in de categorie Alarmsysteem. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

Product Overview

The strobe outdoor siren can be used as a wireless siren by connecting to the control panel as well as a

standalone alarm system to work with wireless accessories in same frequency by learning.

The solar-powered siren is a totally wireless siren, designed to help protect yards, driveways, gardens

and all types of other external locations. The strobe siren is battery powered and kept re-charging by

the built-in solar panel. The signal transmission is all by wireless radio frequency which achieves

significantly wirefree transmission and enhances the flexibility to install. Users can install some outdoor

strobe sirens to deter the intruders in Omni-directional guard.

SPS-260

Solar-Powered Siren

User Manual

PCB Layout

2minutes

Siren Duration Setting

5minutes

5MIN 2MIN 30S 5MIN 2MIN 30S

Volume Setting

High (default) Mute

HIGH MUTE LOW

HIGH MUTE LOW HIGH MUTE LOW

Low

Jumper Setup

30seconds (default)

5MIN 2MIN 30S

1. Load the 9V battery.

2. Set the volume and duration of the siren.

3. Start to use by pressing the power button on.

Connect to Alarm Panel

Press the learning button (0.5 seconds), the wireless siren goes into

connecting status after one beep is heard. Press or button on Arm

the panel. The wireless siren is connected successfully with the control

panel after another beep.

To give up the connection, press the learning button again to exit.

Note: Please don't trigger any accessory during connecting with alarm panel.

Usage

Work as a Wireless Siren

After connected to the alarm panel, the siren will hoot and the strobe light will flash when the alarm

panel alarms.

Getting Started

External Tamper Switch

Note: The status LED will flash once every 5 seconds in arm status. It will not flash when in disarm status.

The siren will sound immediately if the tamper switch is triggered.

Learning Button

Internal Tamper Switch

Status LED Indicator

Alarm LED Indicators

Volume Setting

Siren Duration Setting

Power On/Off

18650

9V 6F22

Installation

Note: No matter the siren works as a wireless siren or an alarm panel, if disarm is not operated after the

siren duration time, the status indicator of siren will flash once every 2 seconds to inform user or patrol

police that the alarm system has been triggered. This LED indication lasts for 1 hour.

Work as an Alarm Panel

Service Mode

When the siren is working as a standalone alarm system and installed on the wall, newly purchased

accessories may not easy to connect with the siren. With this function, user can easily connect the

accessories to the siren without dismounting the siren from the wall.

Press on the remote control 3 times (within 5 seconds) to enter service mode.

Then press 3 times (within 5 seconds) to enter connecting status.

A longer beep is heard from the siren means it enters connecting status, press test button on the newly

purchased accessory or trigger the accessory once. Another beep is heard from the siren, the accessory

has been successfully connected with the siren.

Press on remote control to exit connecting status after a short beep.

Enter/Exit Connecting Status by Connected Remote Control

Ver : SPS-260-EN-1407-V2.0-1

2014 Chuango. All Rights Reser ved.

Specifications

Backup Power

Solar Panel Output Current

Maximum Alarm Current

Wireless Receiving Distance

Operation Condition:

Maximum Siren Volume

Static Current

Standby Time

Wireless Receiving Frequency

Housing Material

Size (L x W x H)

Drill four holes and

fit the wall plugs,

and then fit

supplied fixing

screws in the

holes.

Hinge the front cover

locating tabs over the top

edge of the back plate and

carefully push the base of

the siren cover into place.

Secure the siren cover in

place by refitting the fixing

screw in the bottom edge

of the cover.

After connected with wireless accessories, the siren will hoot and the strobe light will flash to deter the

burglar on site when the accessories detect intrusion.

Hold the mounting

plate in position and

mark the positions of

the four mounting

holes. A spirit level

placed on the water-

proof casing will ensure

a perfect level.

Remove the fixing

screw from the bottom

edge of the siren

housing and carefully

remove front cover.

Connect with Wireless Accessories

Press the learning button (0.5 seconds), the system goes into connecting status after one beep is heard.

Press test button on accessories or trigger the accessory once. The wireless accessory is connected

successfully after another beep. To give up the connection, press the learning button again to exit

connecting status after one beep.

18650 3.7V 1200mAh rechargeable lithium battery x 1

9V 6F22 battery x 1

2000LUX illumination 4mA (in sunlight) ≥

≤500mA

≤80m (in open area)

Temperature -10 55 ℃～+ ℃

Relative Humidity 80% (non-condensing) ≤

110dB

≤1mA

≤30 days (in case of no sunlight)

433.92MHz ( ±75KHz)

PC + ABS + ANTI-UV

309 x 230 x 79.7mm

The service mode is to prevent triggering the alarm when you mount the siren on the wall.

When the remote control is connected with the siren, press on remote control 3 times (within 5

seconds), the siren goes into service mode when a long beep is heard. During this period, the siren will

not alarm but beep even if the tamper switch or the sensors connected are triggered. This brings you

convenience on installation.

Press on remote control to exit service mode after a short beep.

Product specificaties

Merk:	Chuango
Categorie:	Alarmsysteem
Model:	SPS-260
Kleur van het product:	Black, Red, White
Soort:	Draadloze sirene
Internationale veiligheidscode (IP):	IP55
Accu/Batterij voltage:	3.7 V
Alarm decibels:	115 dB
Stroom in standby:	1200 mA