Chief RPMA281 Handleiding

Chief Flat panel steun RPMA281

Lees hieronder de 📖 handleiding in het Nederlandse voor Chief RPMA281 (12 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12

I N S T A L L A T I O N I N S T R U C T I O N S

Instrucciones de instalación

Installationsanleitung

Instruções de Instalação

Istruzioni di installazione

Installatie-instructies

Instructions d´installation

RPA Elite Series Projector Mounts

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

RPMA/RPMB/RPMC Series

RPMA/RPMB/RPMC Series Installation Instructions

NOTE: RPMA, RPMB, and RPMC models are included in

these installation instructions. Throughout these

instructions "RPMX" is used to designate all of the

models covered by these instructions.

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to the RPMX does not exceed 50 lbs

(22.7 kg).

• The weight capacity of the RPMX may be LIMITED to

the lowest weight capacity of any other components

located between the RPMX and the supporting

structure!

WARNING: Use this mounting system only for its intended

use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is

damaged. Return the mounting system to a service center for

examination and repair.

WARNING: Do not use this product outdoors.

IMPORTANT ! : The RPMX mounts are designed to be:

• mounted to a 1-1/2" NPT or NPSM following ANSI/

ASME B1.20.1 (Schedule 40, 0.154" minimum

thickness aluminum - ASTM B221) threaded extension

column;

• mounted to double 2" x 4" wood stud cross bracing

(1-1/2" on center) between two 2" x 4" ceiling joists with

a maximum drywall covering of 5/8";

• mounted to a concrete ceiling with a minimum

thickness of 8" and a maximum drywall covering of

5/8"; or

• suspended from four #10-24 grade ASTM A307 or

better threaded rods (not included) which are secured

to unistrut, angle or channel assembly overhead

structural members (trusses or I-beams) by #10-24

grade ASTM A307 or better jam nuts (not included).

--SAVE THESE INSTRUCTIONS--

Installation Instructions RPMA/RPMB/RPMC Series

DIMENSIONS

TOOLS REQUIRED FOR INSTALLATION

PARTS

2.79

5.241.00

ROLL ADJUSTMENT

POINT

5.50

6.50

5.50

4.50

1.50" DIA NPT

SECURITY LOCK

SECURITY SWITCH

PITCH ADJUSTMENT

POINT

YAW ADJUSTMENT

POINT 20

1/4" (6.4mm) dia. (concrete)

3/32" (2.4mm) dia. (wood)

5/32" - security

(included)

A (1)

[RPMA/-B/-C]

B (1)

[Example of SLM bracket]

Product specificaties

Merk:	Chief
Categorie:	Flat panel steun
Model:	RPMA281
Kleur van het product:	Zwart
Montagewijze:	Plafond
Maximale gewichtscapaciteit:	- kg
Code geharmoniseerd systeem (HS):	83024190