Chief HB42E Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Chief HB42E (2 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
I N S TA L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, Inc., and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone
makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation
or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, ex-
pressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this
document.
© 2008 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8803-000108 RevA
1/09
MODEL: HB-42E Custom Projector Bracket
Unpack carton and verify contents. If any listed parts are miss by calling ing, immediately contact a Chief Customer Service representative
1-800-582-6480.
PARTS
Figure 1:
INSTALLATION
WARNING:
IMPROPER INSTALLATION MAY RESULT IN SERIOUS PERSONAL INJURY! All components must be securely fastened
to each other and to the ceiling, and the ceiling must be capable of supporting five times the total weight of the installation.
1. Stack nylon spacers on top of each other and on top of projector under center hole. (See Figure 1)
2. Lower custom HB bracket onto nylon spacers. Ensure that the two corner tabs are toward the back of the projector, and three tabs toward
the front. (See Figure 1)
3. Attach HB bracket to projector using one M8 x 45mm button head screw and flat washer through center hole and nylon spacers. (See
Figure 1)
4. Install seven M8 x 12mm button head screws and M8 flat washers through corner and end tabs on bracket. (See Figure 1)
(1) BRACKET, Custom HB (4) NUT, Flange, Hex, 5/16-18
(7) SCREW, Button Head, M8 x 12mm (2) NYLON SPACER, .680x.390x.625
(1) SCREW, Button Head, M8 x 45mm (8) WASHER, Flat, M8
(1) KEY, Hex, M5
Corner tabs
toward back
of projector
1
3
x 1
x
4
x 7
I N S T A L L A T I O N I N S T R U C T I O N S
Continued
Continued...
CAUTION:
Installing a ceiling mount requires the presence of two persons familiar with mechanical installations. A third assistant is
recommended.
Figure 2:
5. Attach VCM housing to your method of support and tighten firmly so the VCM housing is square to the screen.
6. With help of assistants, lift the projector and install it to the VCM housing. Ensure that the the four studs extending from VCM housing is
seated in slots on HB bracket. (See Figure 2)
7. Tighten the four 5/16" flange nuts. (See Figure 2)
6
7
VCM Housing
x 4
Seat VCM in HB
bracket slots


Product specificaties

Merk: Chief
Categorie: Projector accessoire
Model: HB42E

Heb je hulp nodig?

Als je hulp nodig hebt met Chief HB42E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Projector accessoire Chief

Handleiding Projector accessoire

Nieuwste handleidingen voor Projector accessoire