Chief HB29S Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Chief HB29S (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
I N S TA L L A T I O N I N S T R U C T I O N S
Continued...
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F: 877.894.6918 / 952.894.6918
8803-000120
©2008 Milestone AV Technologies
9/30/08
MODEL: HB-29S Custom Projector Bracket
Unpack carton and verify contents. If any listed parts are miss by calling ing, immediately contact a Chief Customer Service representative
1-800-582-6480.
PARTS
Figure 1:
INSTALLATION
WARNING:
IMPROPER INSTALLATION MAY RESULT IN SERIOUS PERSONAL INJURY! All components must be securely fastened
to each other and to the ceiling, and the ceiling must be capable of supporting five times the total weight of the installation.
CAUTION:
This HB bracket mount is designed to support the weight of only one projector per mount. DO NOT attempt to attach more
than one projector to the same mount!
1. Place custom HB bracket on underside of the projector and line up the four screw holes on the bracket with the four corresponding holes
on the projector. Ensure that the side hooks open towards back of the projector. (See Figure 1)
2. Attach HB bracket to projector using four M6-1.00 x 16mm Phillips machine screws through washers and spacers into projector. Install
each screw partially to make sure all screws are aligned correctly before tightening the screws to the bracket. (See Figure 1)
(1) BRACKET, Custom HB (4) NUT, Flange, Hex, 5/16-18
(4) SCREW, Phillips Machine, M6-1.00 x
16mm
(4) FLAT WASHER, Standard Machine
Screw 6mm
1
2
x 4
Toward front
of projector
I N S T A L L A T I O N I N S T R U C T I O N S
Continued...
CAUTION:
Installing a ceiling mount requires the presence of two persons familiar with mechanical installations. A third assistant is
recommended.
Figure 2:
3. Attach VCM housing to your method of support and tighten firmly so the VCM housing is square to the screen.
4. With help of assistants, lift the projector and install it to the VCM housing. Ensure that the the four studs extending from VCM housing is
seated in slots on HB bracket. (See Figure 2)
5. Tighten the four 5/16" flange nuts. (See Figure 2)
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
4
5
VCM Housing
x 4
Seat VCM in HB
bracket slots


Product specificaties

Merk: Chief
Categorie: Flat panel steun
Model: HB29S

Heb je hulp nodig?

Als je hulp nodig hebt met Chief HB29S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Flat panel steun Chief

Handleiding Flat panel steun

Nieuwste handleidingen voor Flat panel steun