Chief CPA261 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Chief CPA261 (4 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
I N S T A L L A T I O N I N S T R U C T I O N S
CPA to Female NPT Adapter Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
CPA261
CPA261 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
CPA261 does not exceed 500 lbs (226.8 kg).
•The weight capacity of the CPA261 may be
LIMITED to the lowest weight capacity of any other
component or accessory used within the mounting
system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
NOTE: Accessory is intended to be used with the UL Listed
CPA Extension Column Series and a 1-1/2" NPT or
NPSM following ANSI/ASME B1.20.1 (Schedule 40,
0.154" minimum thickness aluminum-ASTM B221)
threaded extension column (not included).
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
4.00
101.6
1-1/2" NPSM
INTERNAL THREAD
1.90
48.3
7.9
0.31
25.4
1.00
1.88
47.8
0.25
6.4
SIZED FOR 5/16-18
SELF TAPPING SCREWS
2.25
57.2
DIMENSIONS: INCHES
[MILLIMETERS]
CPA261 Installation Instructions
3
TOOLS REQUIRED FOR INSTALLATION / PARTS
5/32"
(included)
A (1)
[CPA261 Coupler]
B (1)
5/16 x 1/2"
C (1)
5/32"
INSTALLATION
IMPORTANT ! : The following procedure assumes that a
1-1/2" NPT or NPSM following ANSI/ASME B1.20.1
(Schedule 40, 0.154" minimum thickness aluminum-
ASTM B221) threaded extension column (not included)
has been properly installed following instructions
provided with extension column.
NOTE: The CPA261 adapts a
1-1/2" NPT or NPSM following
ANSI/ASME B1.20.1 (Schedule 40, 0.154" minimum
thickness aluminum-ASTM B221) threaded extension
column (not included); to a UL Listed CPA Extension
Column Series.
1. Thread CPA261 (A) onto
a 1-1/2" NPT or NPSM following
ANSI/ASME B1.20.1 (Schedule 40, 0.154" minimum
thickness aluminum-ASTM B221) threaded extension
column (not included)
until tight, with a minimum of four
threads engaged. (See Figure 1)
2. Install and tighten one 5/16" x 1/2" set screw (B) through
CPA261 and against column. (See Figure 1)
Figure 1
3. Install UL Listed CPA Extension Column Series following
instructions included with extension column.
1
1
2
(B) x 1
5/16" holes/slots -- 1/2" apart
(on each side of CPA261)


Product specificaties

Merk: Chief
Categorie: Projector accessoire
Model: CPA261

Heb je hulp nodig?

Als je hulp nodig hebt met Chief CPA261 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Projector accessoire Chief

Handleiding Projector accessoire

Nieuwste handleidingen voor Projector accessoire