Chauvin Arnoux CA 10101 Handleiding

Chauvin Arnoux Meetapparatuur CA 10101

Lees hieronder de 📖 handleiding in het Nederlandse voor Chauvin Arnoux CA 10101 (38 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/38

pH-meter

EN - User’s manual

C.A 10101

Information or useful tip.

Battery.

Earth.

The product is declared recyclable following an analysis of the life cycle in accordance with standard ISO 14040.

Chauvin Arnoux has adopted an Eco-Design approach in order to design this appliance. Analysis of the complete life-

cycle has enabled us to control and optimize the e󰀨ects of the product on the environment. In particular this appliance

exceeds regulation requirements with respect to recycling and reuse.

The CE marking indicates conformity with European directives, in particular LVD and EMC.

The rubbish bin with a line through it indicates that, in the European Union, the product must undergo selective disposal

in compliance with Directive WEEE 2012/19/EU. This equipment must not be treated as household waste.

PRECAUTIONS FOR USE

This instrument is compliant with safety standard IEC 61010-2-030, for voltages 5V with report to ground. Failure to observe the

safety instructions may result in electric shock, re, explosion, and destruction of the instrument and of the installations.

The operator and/or the responsible authority must carefully read and clearly understand the various precautions to be taken

in use. Sound knowledge and a keen awareness of electrical hazards are essential when using this instrument.

Observe the conditions of use, namely the temperature, the relative humidity, the altitude, the degree of pollution, and the

place of use.

Do not use the instrument if it seems to be damaged, incomplete, or poorly close.

Before each use, check the condition of the housing. Any item of which the insulation is deteriorated (even partially) must be

set aside for repair or scrapping.

All troubleshooting and metrological checks must be done by competent, accredited personnel.

Keep your electrode in a bottle containing an electrolytic solution.

Thank you for purchasing this C.A 10101 pH-meter.

For best results with your instrument:

read these operating instructions carefully,

comply with the precautions for use.

CONTENTS

1. FIRST USE ............................................................................................................................................................................... 4

1.1. Delivery condition 4 ...........................................................................................................................................................

1.2. Accessories .................................................................................................................................................................... 5

1.3. Replacement parts 5 .........................................................................................................................................................

1.4. Inserting the batteries 6 .....................................................................................................................................................

2. PRESENTATION OF THE INSTRUMENT ............................................................................................................................. 7

2.1. C.A 10101 7 .......................................................................................................................................................................

2.2. Functions of the instrument 8 ............................................................................................................................................

2.3. Keypad 8 ...........................................................................................................................................................................

2.4. Display 9 ............................................................................................................................................................................

2.5. Setting the time 9 ...............................................................................................................................................................

2.6. Prop 10 ..............................................................................................................................................................................

3. USE IN STAND-ALONE MODE ............................................................................................................................................11

3.1. pH measurement ...........................................................................................................................................................11

3.2. Oxidation reduction potential measurement (ORP) 17 .....................................................................................................

3.3. Recording the measurements 20 ......................................................................................................................................

3.4. Errors 21 ............................................................................................................................................................................

4. USE IN RECORDING MODE ............................................................................................................................................... 22

4.1. Connection 22 ...................................................................................................................................................................

4.2. Get Data Logger Transfer software 22 ..............................................................................................................................

4.3. USB link 22 ........................................................................................................................................................................

4.4. Data Logger Transfer software 25 .....................................................................................................................................

5. TECHNICAL CHARACTERISTICS ..................................................................................................................................... 28

5.1. Reference conditions 28 ....................................................................................................................................................

5.2. Characteristics 28 ..............................................................................................................................................................

5.3. Memory 30 .........................................................................................................................................................................

5.4. USB 30 ..............................................................................................................................................................................

5.5. Power supply 30 ................................................................................................................................................................

5.6. Environmental conditions 31 .............................................................................................................................................

5.7. Mechanical characteristics 32 ..........................................................................................................................................

5.8. Compliance with international standards 32 ......................................................................................................................

5.9. Electromagnetic compatibility (EMC) 32 ............................................................................................................................

6. MAINTENANCE ..................................................................................................................................................................... 33

6.1. Cleaning 33 .......................................................................................................................................................................

6.2. Replacement of batteries 34 ..............................................................................................................................................

6.3. Serial number 34 ...............................................................................................................................................................

6.4. Calibration log 34 ...............................................................................................................................................................

6.5. Embedded software version 34 .........................................................................................................................................

6.6. Updating the embedded software 34 .................................................................................................................................

7. WARRANTY ........................................................................................................................................................................... 37