Celestron Inspire 100AZ Handleiding

Celestron Telescoop Inspire 100AZ

Lees hieronder de 📖 handleiding in het Nederlandse voor Celestron Inspire 100AZ (40 pagina's) in de categorie Telescoop. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/40

INSTRUCTION MANUAL

Model #22401- Inspire 70AZ

Model #22402- Inspire 80AZ

Model #22403- Inspire 100AZ

Model #22407- Inspire 90AZS

ENGLISH

2 | ENGLISH

1. Telescope Tube

2. StarPointer Pro Finderscope

3. 20 mm Eyepiece

4. Erect Image Diagonal

5. Focus Knob

6. Focus Micrometer

7. Panning Handle/Altitude Clutch Knob

8. Tripod

9. Accessory Tray Lock Knob

10. Folding Accessory Tray

11. Lens Cap/Smartphone Adapter

12. Tube Mounting Bolt

13. Altazimuth Mount

14. Removable Flashlight

15. Accessory Tray Tension Knob

16. 10 mm Eyepiece

SOLAR WARNING

Never look directly at the Sun with the naked eye or with a telescope unless you have the proper solar filter. Permanent and irreversible eye damage may result.

Never use your telescope to project an image of the Sun onto any surface. Internal heat build-up can damage the telescope and any accessories attached to it.

Never use an eyepiece solar ﬁlter or a Herschel wedge. Internal heat build-up inside the telescope can cause these devices to crack or break, allowing unﬁltered sunlight to pass through to the eye.

Do not leave the telescope unsupervised, especially when children or adults unfamiliar with the correct operating procedures of your telescope are present.

We recommend saving your telescope box so it can be used to store the telescope when it is not in use. Unpack the box carefully

as some parts are small. Use the parts list below to verify that all parts and accessories are present.

PARTS LIST

WHAT’S IN THE BOX

ASSEMBLING YOUR TELESCOPE

THE MOUNT

The Inspire mount and tripod come fully assembled, so setting it

up is easy.

1. Remove the tripod and mount from the box.

2. Loosen the hand knobs at the bottom of each leg and extend

the inner section of the leg to the desired length. Tighten the

knobs to secure the legs, being careful not to over tighten.

3. Stand the tripod upright and pull the tripod legs apart until the

folding accessory tray snaps into place.

4. Line up the tabs on the spring-loaded accessory tray locking

knob with the notches in the accessory tray and press

downward. Turn the locking knob clockwise about 20 degrees

to fully lock the tray in place.

5. Turn the accessory tray tension knob clockwise until it stops.

Do not over tighten.

NOTE: When closing the tripod at the end of the observing session, be sure to ﬁrst loosen the tension

knob all the way, then loosen the locking knob by turning it counterclockwise until the spring

pops the locking knob upward. Grab the knob and lift upward and the tripod will fold up.

413

Tension Knob

Locking Knob

ENGLISH | 3

To attach the telescope tube to your tripod and mount:

1. Loosen the two tube mounting bolts on the side of the dovetail

saddle on top of the mount.

2. Locate the dovetail bar on the bottom of the telescope tube

and slide it into the saddle. The eyepiece end of the telescope

tube should point in the same direction as the panning handle

on the mount.

3. When the dovetail is centered in the saddle, tighten the two

tube mounting bolts, starting with the larger one ﬁrst. Finish by

tightening the smaller one.

4. Remove the lens cap when you are ready to observe by simply

pulling it off the lens shade.

The Inspire telescopes come with a 90° erect image diagonal.

This accessory uses a prism to bend the light at a 90° angle,

providing a more comfortable viewing position. It also gives you

a 100% correctly oriented image allowing you to easily use this

telescope for daytime terrestrial observing.

To install the erect image diagonal:

1. Remove the caps from both sides of the diagonal.

2. Loosen the setscrews on the back of the telescope focuser and

pull out the small dust cap.

3. Insert the smaller tube on the diagonal into the back of the

focuser and secure it by tightening the setscrews.

Your Inspire telescope comes with two eyepieces, a low power

(20 mm eyepiece) and a higher power eyepiece (10 mm eyepiece).

Whenever you set up your telescope, always start with the 20

mm eyepiece. Once you have your target centered in the 20 mm

eyepiece, you can switch to your higher power 10 mm eyepiece to

increase magniﬁcation and get a more detailed view.

To install an eyepiece:

1. Loosen the setscrews on the open end of the erect image diagonal.

2. Insert the silver barrel of the 20 mm eyepiece into the diagonal.

3. Tighten the setscrews to secure the eyepiece.

4. To see the sharpest image possible, you need to adjust the

telescope’s focus. Look through the eyepiece and slowly turn

the focusing knobs until you see the sharpest image possible.

NOTE: You should always adjust focus whenever you change eyepieces or if another person views

through the telescope as the focus may be different for each individual.

THE ERECT DIAGONAL

THE TELESCOPE TUBE

THE EYEPIECES

Product specificaties

Merk:	Celestron
Categorie:	Telescoop
Model:	Inspire 100AZ
Kleur van het product:	Black, Blue
Soort:	Breker
Diameter:	100 mm
Vaste focale lengte:	660 mm
Vergroting:	241 x
Vaste opening:	100 mm
Lens-bedekking:	Volledig gecoat
Maximale ondersteunde oogstuk diameter:	20 mm
Statief materiaal:	Staal
Altazimuth montage:	Ja
Compatible eyepieces:	10, 20 mm
Focaal ratio:	6.5
Visuele power (max):	212 x