Cateye TIGHT KINETICTL-LD180K Handleiding

Bekijk gratis de handleiding van Cateye TIGHT KINETICTL-LD180K (2 pagina’s), behorend tot de categorie Verlichting. Deze gids werd als nuttig beoordeeld door 27 mensen en kreeg gemiddeld 4.5 sterren uit 2 reviews. Heb je een vraag over Cateye TIGHT KINETICTL-LD180K of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Manual

TL-LD180K

+

+

-

-

Caution!:

Do not drop!

90˚

2

3

2

SWITCH OPERATION

Design Pat. Pending

Copyright© 2020 CATEYE Co., Ltd.

TLLD180K-200710

1

1

HOW TO INSTALL BATTERY

3

HOW TO MOUNT

Before using the light, read this

manual thoroughly and keep it

for future reference.

FlexTight™ bracket (SP-11)

AAA alkaline batteries

1

3

AAA batteries × 2

2

1. Rotate the dial and pull out the body from the

lens as shown.

* Be sure to securely hold the unit while

operating. If dropped accidentally, unexpected

damage may occur.

2. Insert the batteries according to the orientation

marked on the body.

3. Reattach the lens in the reverse order.

CAUTION!

• Do not use in combination with new and old

batteries, or different types of batteries.

•

Be sure to install batteries in the correct direction.

• To ensure waterproof performance, align the

packing (rubber seal) with the groove on the

body and securely attach the lens, then tighten

the dial so that it is not loose.

• Remove and store batteries when you will not

use the light for a long period of time.

Otherwise, batteries may leak liquid, which

may result in failure.

12

3

13

4

5

6

4

6

5

Click

1

2

3

Seat post/stay

Mounting diameter

ø

12 – 32 mm

MountingMounting

View from above

Removing

*1

1.

Mount the bracket on the seat post or the seat stay

as shown. to

2. Install the light unit on the bracket until a click

is heard , then loosen the dial and adjust the

lighting angle so that the light unit is perpendic-

ular to the ground.

3. To remove the light unit, slide the light while

pressing the release button.

CAUTION!

• Be sure to tighten the dial by hand. If tightened

too hard with a tool, the screw thread may be

stripped.

• Check the bracket periodically to ensure that it

is securely attached and never use the light

when loose.

•

Round off the cut edge of the bracket strap to

prevent injury. (*1)

WARNING!!!

To prevent accidents and to ensure safe riding,

make sure the light is securely attached to the

bracket and it is functioning properly before the

ride.

CAUTION!

• This light detects deceleration through the use of

acceleration sensor. Please note that activation

of the Kinetic function depends on the degree of

deceleration, the light may not react or the

reaction may be delayed.

• Stop your bicycle to operate the switch.

• This device is rated IPX7 based on JIS C0920.

Do not use the product while immersed in water.

Doing so may cause a malfunction. Wipe off any

moisture after use.

• If the light unit or parts become dirty with mud,

etc., clean with a soft cloth which is moistened

with mild soap. Never apply paint thinner,

benzine or alcohol; damage will result.

* When turning the light on, it lights up in the mode that was used last

time. (Mode memory function)

OFFON

Rapid

Constant

(Low)

Flashing

Brake mode

(Kinetic function)

When bicycle deceleration is

detected, the light will illuminate for

about 2.5 seconds (on High)

regardless of the mode. Illumina-

tion (on High) will continue while

deceleration is detected.

Constant (High)

ENG

Lens

Dial

Body

Packing

(Rubber seal)

Packing

(Rubber seal)

Switch

Click

Light unit

Dial

Strap

Release button

Press and hold

Slide

(x2)

Press and hold

Product specificaties