Casio Baby-G BGA-255-5AER Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Casio Baby-G BGA-255-5AER (7 pagina's) in de categorie Horloge. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/7
Operation Guide 5593
E-9
Hand Setting Mode
C
Stopwatch Mode Alarm Mode
C C
E-8
Selecting a Mode
x Press C to cycle between the modes as shown below.
x In any mode (except when a setting screen, with flashing digits is on the display),
press to illuminate the display.B
Timekeeping Mode
C
World Time Mode Countdown Timer Mode
C C
E-7
Mode Reference Guide
Your watch has 6 “modes”. The mode you should select depends on what you
want to do.
To do this: Enter this mode: See:
x View the current date in the Home City
x Configure Home City and daylight saving time (DST)
settings
x Configure time and date settings
Timekeeping Mode E-11
View the current time in one of 27 cities
(29 time zones) around the globe World Time Mode E-19
Use the countdown timer Countdown Timer Mode E-21
Use the stopwatch to measure elapsed time Stopwatch Mode E-27
Set an alarm time Alarm Mode E-30
Adjust the analog hands Hand Setting Mode E-34
E-6
To turn an alarm and the Hourly Time Signal on and off……………………E-33
To stop the alarm ………………………………………………………………E-33
Adjusting the Analog Hand Setting…………………………………………………E-34
To adjust the analog time ………………………………………………………E-34
Illumination ……………………………………………………………………………E-36
To turn on illumination …………………………………………………………E-36
To change the illumination duration …………………………………………E-37
Troubleshooting ………………………………………………………………………E-38
Specifications …………………………………………………………………………E-39
Operating Precautions ………………………………………………………………E-41
User Maintenance ……………………………………………………………………E-52
E-5
To specify standard time or daylight saving time (DST) for a city …………E-20
Countdown Timer………………………………………………………………………E-21
To enter the Countdown Timer Mode …………………………………………E-21
To configure the countdown timer ……………………………………………E-24
To perform a countdown timer operation ……………………………………E-26
To stop the alarm ………………………………………………………………E-26
Using the Stopwatch …………………………………………………………………E-27
To enter the Stopwatch Mode …………………………………………………E-27
To perform an elapsed time operation ………………………………………E-28
To pause at a split time …………………………………………………………E-28
To measure two finishes ………………………………………………………E-28
Using the Alarm ………………………………………………………………………E-30
To enter the Alarm Mode ………………………………………………………E-31
To set an alarm time ……………………………………………………………E-32
To test the alarm ………………………………………………………………E-33
E-4
Contents
About This Manual …………………………………………………………………… E-2
Things to check before using the watch ………………………………………… E-3
Mode Reference Guide ……………………………………………………………… E-7
Timekeeping ……………………………………………………………………………E-11
Configuring Home City Settings ……………………………………………………E-12
To configure Home City settings ………………………………………………E-12
To change the Daylight Saving Time (summer time) setting ………………E-14
Adjusting the Digital Time and Date Settings ……………………………………E-15
To configure the digital time and date settings ………………………………E-15
Checking the Current Time in a Different Time Zone ……………………………E-19
To enter the World Time Mode ………………………………………………E-19
To view the time in another time zone ………………………………………E-19
E-3
Things to check before using the watch
1. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To configure Home City settings” (page E-12) to configure
your Home City and daylight saving time settings.
Important!
x Proper World Time Mode data depend on correct Home City, time, and date
settings in the Timekeeping Mode. Make sure you configure these settings
correctly.
2. Set the current time.
x See “Adjusting the Digital Time and Date Settings” (page E-15).
The watch is now ready for use.
E-2
About This Manual
x Depending on the model of your watch, display text appears either as dark figures
on a light background, or light figures on a dark background. All sample displays in
this manual are shown using dark figures on a light background.
x Button operations are indicated using the letters shown in the illustration.
x Note that the product illustrations in this manual are intended for reference only,
and so the actual product may appear somewhat different than depicted by an
illustration.
E-1
ENGLISH
Congratulations upon your selection of this CASIO watch.
To ensure that this watch provides you with the years of service for which it is
designed, carefully read and follow the instructions in this manual, especially the
information under “Operating Precautions” and “User Maintenance”.
MO1809-EA © 2018 CASIO COMPUTER CO., LTD.
Operation Guide 5593
E-19
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current
time in one of 29 time zones (27 cities) around the
globe. The city that is currently selected in the World
Time Mode is called the “World Time City”.
To enter the World Time Mode
Use to select the World Time Mode as shown on C
page E-8.
To view the time in another time zone
In the World Time Mode, use (East) to scroll through D
city codes.
Currently selected
World Time City
Current time in the currently
selected World Time City
E-18
Note
x For information about selecting a Home City and configuring the DST setting, see
“Configuring Home City Settings” (page E-12).
x While 12-hour format is selected for timekeeping, a indicator will appear for PM
times from noon to 11:59 p.m. No indicator appears for times from midnight to
11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without any
PM indicator.
x The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
x The day of the week changes automatically when the date changes.
E-17
3. When the timekeeping setting you want to change is flashing, use and/or D B
to change it as described below.
Screen To do this: Do this:
Reset the seconds to 00 Press D.
Toggle between Daylight Saving Time (ON)
and Standard Time (OFF)Press D.
Change the city code Use (East) and (West).D B
Change the hour or minute Use (+) and (–).D B
Toggle between 12-hour ( ) and 24-hour 12H
(24H) timekeeping Press D.
Change the year, month, or day Use (+) and (–).D B
4. Press to exit the setting screen.A
E-16
2. Press to move the flashing in the sequence shown below to select the other C
settings.
Time and Date
Seconds
C
DST
C
Home City Code
C
Hour
C
Minutes
C C
Illumination Duration
C
Day
C
Month
C
Year
C
12/24-Hour Format
x The following steps explain how to configure timekeeping settings only.
E-15
Adjusting the Digital Time and Date Settings
Use the procedure below to adjust the digital time and date settings.
Note
x After adjusting the digital time and date setting, be sure to adjust the analog hands
so the settings match.
x See “Adjusting the Analog Hand Setting” (page E-34).
To configure the digital time and date settings
1. In the Timekeeping Mode, hold down for about twoA
seconds until the seconds start to flash. This is the
setting screen.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Seconds
E-14
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down for about two A
seconds until the seconds start to flash. This is the
setting screen.
2. Press to display the DST setting screen.C
3. Press to toggle between Daylight Saving Time (On) D
and Standard Time (OFF).
4. After the setting is the way you want, press to A
return to the Timekeeping Mode.
x The indicator appears to indicate that Daylight DST
Saving Time is turned on.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
DST indicator
E-13
2. Press twice to move the flashing to the city code.C
x For details about city codes, see the “City Code
Table” at the back of this manual.
3. Press (East) and (West) to select the city code D B
you want to use as your Home City.
x Keep pressing or until the city code you want D B
to select as your Home City appears on the display.
4. After the setting is the way you want, press toA
return to the Timekeeping Mode.
Note
x After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current time
in your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping.
The reference point for UTC is Greenwich, England.
City Code
E-12
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City, and selecting
either standard time or daylight saving time (DST).
Note
x After configuring Home City and/or Daylight Saving Time
(summer time) settings, be sure to adjust the analog
hands to match the digital settings.
x See “Adjusting the Analog Hand Setting” (page E-34).
To configure Home City settings
1. In the Timekeeping Mode, hold down for about twoA
seconds until the seconds start to flash. This is the
setting screen.
x The watch will exit the setting screen automatically
if you do not perform any operation for about two or
three minutes.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Seconds
E-11
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
x Each press of D cycles the digital display contents as
shown below.
D D D
PM indicator
D
Day of the Week Month-Day Hour : Minutes Seconds
Hour
Day of week
Minutes
E-10
General Functions (All Modes)
The functions and operations described in this section can be used in all of the
modes.
Auto Return Features
If you leave a setting screen with flashing digits on the display for two or three
minutes without performing any operation, the watch exits the setting screen
automatically.
Initial Screens
When you enter the World Time Mode or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
Scrolling
The and buttons are used on the setting screen to scroll through data on the B D
display. In most cases, holding down these buttons during a scroll operation scrolls
through the data at high speed.
Operation Guide 5593
E-29
Note
x The Stopwatch Mode can indicate elapsed time up to 59minutes, 59seconds.
x An ongoing elapsed time measurement operation will continue internally even if
you change to another mode. However, if you exit the Stopwatch Mode while a
split time is displayed, the split time will not be displayed when you return to the
Stopwatch Mode.
E-28
To perform an elapsed time operation
D D D D A
Start Stop (Resume) (Stop) Reset
To pause at a split time
D A A D A
Start Split
(SPL displayed)
Split release Stop Reset
To measure two finishes
D A D A A
Start Split
(SPL displayed)
First runner finishes.
Display time of first
runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Reset
E-27
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two finishes.
To enter the Stopwatch Mode
Use to select the Stopwatch Mode as shown on C
page E-9.
Seconds
Minutes
E-26
To perform a countdown timer operation
D D D D A
Start Stop Resume (Stop) Reset
x Before starting a countdown timer operation, check to make sure that a
countdown operation is not in progress (indicated by the seconds counting down).
If it is, press D to stop it and then to reset to the countdown start time.A
To stop the alarm
Press any button.
E-25
3. When the setting you want to change is flashing, use and to change it as B D
described below.
Setting Screen Button Operation
Start Time
Use (+) and (–) to change the setting.D B
x You can set a start time in the range of 1 to 60minutes in
1-minute increments.
Auto-repeat Press to toggle auto-repeat on ( displayed) and off D
( displayed).
Progress Beeper Press to toggle the progress beeper on ( ) and off D
( ).
4. Press to exit the setting screen.A
x You can also perform steps 1 and 2 of the above procedure whenever you need
to view the current auto-repeat and progress beeper settings.
E-24
To configure the countdown timer
1. While the countdown start time is on the display in
the Countdown Timer Mode, hold down until the A
current countdown start time starts to flash, which
indicates the setting screen.
x If the countdown start time is not displayed, use the
procedure under “To perform a countdown timer
operation” (page E-26) to display it.
2. Press C to move the flashing in the sequence shown below to select other
settings.
Start Time Auto-repeat Progress Beeper
C C
C
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
E-23
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero.
x When the progress beeper is turned off, the countdown end beeper sounds for
about 10seconds, or until you press any button to stop it.
x When the progress beeper is turned on, the countdown end beeper sounds for
about one second.
Progress Beeper
When the progress beeper is turned on, the watch uses beeps to signal countdown
progress as described below.
x Starting from five minutes before the end of the countdown, the watch emits four
short beeps at the top of each countdown minute.
x 30seconds before the end of the countdown, the watch emits four short beeps.
x The watch emits a short beep for each of the last 10seconds of the countdown.
x If the countdown start time is six minutes or greater, the watch emits a short beep
for each second of the final 10seconds before the five-minute point is reached.
Four short beeps are emitted to signal when the five-minute point is reached.
E-22
x See “To configure the countdown timer” on page E-24 for information about setting
up the timer.
Auto-repeat
When auto-repeat is turned on, the countdown automatically restarts from the
countdown start time when it reaches zero. If left running, the countdown is
repeated a total of eight times, after which it stops automatically.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
x Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing , or you D
can press to reset to the countdown time starting value.A
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes
the types of beeper operations the watch performs during a countdown.
E-21
Countdown Timer
The countdown timer can be set within a range of
one minute to 60minutes. An alarm sounds when the
countdown reaches zero. The countdown timer also has
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.
To enter the Countdown Timer Mode
Use to select the Countdown Timer Mode as shown C
on page E-8.
Configuring the Countdown Timer
The following are the settings you should configure
before actually using the countdown timer.
Countdown start time; Auto-repeat on/off; Progress
beeper on/off
Seconds
Minutes
E-20
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use (East) to display the D
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down for about two seconds.A
x This toggles the city code you selected in step1
between Daylight Saving Time ( indicator DST
displayed) and standard time ( indicator notDST
displayed).
x Using the World Time Mode to change the DST setting of the city code that is
selected as your Home City also will change the Timekeeping Mode time DST
setting.
x Note that you cannot switch between standard time/daylight saving time (DST)
while GMT is selected as the World Time City.
x The standard time/daylight saving time (DST) setting affects only the currently
selected time zone. Other time zones are not affected.
DST indicator
Product specificaties
| Merk: | Casio |
| Categorie: | Horloge |
| Model: | Baby-G BGA-255-5AER |
Heb je hulp nodig?
Als je hulp nodig hebt met Casio Baby-G BGA-255-5AER stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Horloge Casio
20 April 2024
20 April 2024
20 Maart 2024
16 Maart 2024
16 Maart 2024
16 Maart 2024
16 Maart 2024
16 Maart 2024
16 Maart 2024
16 Maart 2024
Handleiding Horloge
- Horloge Braun
- Horloge IKEA
- Horloge Epson
- Horloge Huawei
- Horloge Garmin
- Horloge Medion
- Horloge Topcom
- Horloge Ade
- Horloge Adidas
- Horloge Alessi
- Horloge Alpina
- Horloge Armani
- Horloge Ascot
- Horloge Asics
- Horloge Auriol
- Horloge Beper
- Horloge BML
- Horloge Boss
- Horloge Bruno Sohnle
- Horloge Bulova
- Horloge Bushnell
- Horloge Dakota
- Horloge Danish Design
- Horloge Davis
- Horloge Detomaso
- Horloge Diesel
- Horloge Digi-tech
- Horloge Easypix
- Horloge Ebel
- Horloge Edox
- Horloge ELYSEE
- Horloge ESQ
- Horloge ETA
- Horloge Eurochron
- Horloge Ferrari
- Horloge Festina
- Horloge Fila
- Horloge Fitbit
- Horloge Fossil
- Horloge Freestyle
- Horloge GC Watches
- Horloge Geemarc
- Horloge Guess
- Horloge Habitat
- Horloge Haffstreuner
- Horloge Hamilton
- Horloge Hugo Boss
- Horloge ICE Watch
- Horloge Inter-Quartz
- Horloge Invicta
- Horloge Irox
- Horloge Kalenji
- Horloge Karlsson
- Horloge Kogan
- Horloge Krontaler
- Horloge La Crosse
- Horloge Lambretta
- Horloge Longines
- Horloge Lorus
- Horloge Lotus
- Horloge Lynx
- Horloge Marc Jacobs
- Horloge Marquant
- Horloge Meister Anker
- Horloge Michael Kors
- Horloge Misfit
- Horloge Mitsubishi
- Horloge Mondaine
- Horloge Movado
- Horloge Naitica
- Horloge Naviforce
- Horloge Nedis
- Horloge Nike
- Horloge Polar
- Horloge Pulsar
- Horloge Pyle
- Horloge QQ
- Horloge Rado
- Horloge Renkforce
- Horloge Rodania
- Horloge Rolex
- Horloge Ronda
- Horloge Seiko
- Horloge Sempre
- Horloge Sinn
- Horloge Skmei
- Horloge Slazenger
- Horloge Speedo
- Horloge Spinnaker
- Horloge Stuhrling
- Horloge Suunto
- Horloge Swatch
- Horloge Tauchmeister
- Horloge TCM
- Horloge Technaxx
- Horloge Ticwatch
- Horloge Timer
- Horloge TimeStyle
- Horloge Timex
- Horloge Tissot
- Horloge Tommy Hilfiger
- Horloge TomTom
- Horloge Torgoen
- Horloge TW Steel
- Horloge Uri Minkoff
- Horloge Velleman
- Horloge Westfalia
- Horloge World Timer Chronograph
- Horloge Xonix
- Horloge Jaguar
- Horloge Junghans
- Horloge Just
- Horloge Olivia Burton
- Horloge Omega
- Horloge Oregon Scientific
- Horloge Orient
- Horloge Clas Ohlson
- Horloge Crivit
- Horloge Zenith
- Horloge Citizen
- Horloge Prologue
- Horloge Swiza
- Horloge Victorinox
- Horloge Bering
- Horloge Breitling
- Horloge Breo
- Horloge Brera
- Horloge Calypso
- Horloge Certina
- Horloge Christiaan Van Der Klaauw
- Horloge Christopher Ward
- Horloge Cover
- Horloge Daniel Steiger
- Horloge DMC
- Horloge Dugena
- Horloge Executive
- Horloge Gant
- Horloge Girard-Perregaux
- Horloge Holzkern
- Horloge Hublot
- Horloge HYT
- Horloge IWC
- Horloge Jacques Lemans
- Horloge Lars Larsen
- Horloge Lucien Picard
- Horloge Luminox
- Horloge Maurice Lacroix
- Horloge Nautica
- Horloge Obaku
- Horloge Philip Watch
- Horloge Pilgrim
- Horloge Puma
- Horloge Shinola
- Horloge Skagen
- Horloge So & Co
- Horloge Tikkers
- Horloge Timberland
- Horloge TMI
- Horloge Triwa
- Horloge Tudor
- Horloge Versace
- Horloge WoodWatch
- Horloge Leff
- Horloge ETT
- Horloge Emporio Armani
- Horloge La Crosse Technology
- Horloge Spin Master
- Horloge Raketa
- Horloge Balmain
- Horloge Audemars Piguet
- Horloge Wonky Monkey
- Horloge Iron Annie
- Horloge Julie Julsen
- Horloge KRAEK
- Horloge X-WATCH
- Horloge PAUL HEWITT
- Horloge MICHELE
- Horloge Radley London
- Horloge PANERAI
- Horloge Zeppelin
- Horloge Hype
Nieuwste handleidingen voor Horloge
21 April 2024
21 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024