Canarm APL20-DP-EC Handleiding
Pagina's 8 Niet gecategoriseerd
Bekijk de handleiding van Canarm APL20-DP-EC gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
APL-DP-EC SERIES
CANARM DIRECT DRIVE ARRAY
PLENUM FAN – INFINITUM AIRCORE
OPERATION INSTRUCTIONS AND PARTS MANUAL
READ AND SAVE THESE INSTRUCTIONS
GENERAL SAFETY
1.The APL EC series unit(s) comes with an onboard VFD.
2.All electrical work must be done in accordance with all applicable electrical codes by a
qualified electrician.
3.Prior to wiring the unit, ensure power supply is locked out in the OFF position, and voltage `
matches the motor’s requirement.
4.Do not install or operate this fan in an environment where combustible materials, gases,
fumes. It is intended for well ventilated indoor industrial use only.
5.The motor should be easily accessed for cleaning and maintenance, do not obstruct its air
cooling inlets and outlets.
6.Caution:the unit contains rotating parts and electrical components.Use appropriate
caution when installing and servicing it.
7.Before starting the unit, ensure all parts are secure & the wheel rotates freely.
8.Check and tighten where necessary all nuts, bolts & set screws prior to unit start up (as
some may have loosened during shipment).
9.NOTE: Check and tighten all hardware after 2 days of initial operation.
10.Make sure there is no foreign debris in the fan compartment or lodged in the wheel itself.
11.It is the customers’ responsibility to ensure the installation location is prepared and
adequate under local building codes to bear the weight of the mounted fan.
12.Inspect electrical components prior to completing electrical connections. Make sure
everything is tight and free of damage that may have occurred in shipping.
13.Always wear appropriate safety equipment when installing or servicing the unit.
14.Please follow all applicable national, state/provincial and local codes, all of them will
supersede this manual.
15.Failure to follow the safety instructions in this manual may cause serious injury or
death due to electrical shock or high speed rotating parts.
The purpose of this manual is to aid in the proper installation and operation of the Canarm array Plenum Fan (APL). These instructions are intended
to supplement good general practices and are not intended to overwrite local codes and ordinances.
IT IS THE RESPONSIBILITY OF THE PURCHASER TO ASSURE THAT THE INSTALLATION AND MAINTENANCE OF THIS EQUIPMENT IS
HANDLED BY QUALIFIED PERSONNEL.
Inspect all shipments carefully for damage. THE RECEIVER MUST NOTE ANY DAMAGE ON THE CARRIER’S BILL OF LADING AND FILE A
CLAIM IMMEDIATELY WITH THE FREIGHT COMPANY.
DIMENSION & COMPONENT
M-APL-DP-EC 03_12_24Page 1 of 4
A
C
D
C
A
B
!"#!"!$%&'
()*
!"#!"!$%&'
(+*
!"#!"!$%&'
(,*
!"#!"!$%&'
-*+
./0(-12/134!"#!$%&!'#($)&!*#($)&+++!!#!$%&
./0(512/134!*&!(#($)&!)#($)&!)&++!'#!($!,&
./0(612/134!-&!%#($)&!-#($)&!-&!-#!$)&+!%#!($!,&
./0(,12/134'!&!"#"$)&'.#"$)&'.#!$%&'.#($)&'.#!$%&!,#!($!,&
./0-*12/134'(#!$%&!,#($%&'!#($%&'!#($)&'!#!$'&'!#($)&!-#!$!,&
./0--12/134',&!)#!$%&'(#!$%&''#*$)&'(&''#*$)&'!#!($!,&
./0-+12/134'-#!$%&!-#*$)&'%#*$)&'%#!$'&'%#"$)&'%#!$'&')#-$!,&
&7230.8
4'94:.";3<'8.<32'7"'&7$7='<!>3?
&7%"$!";
APL-DIRECT DRIVE EC SERIES
CANARM ARRAY PLENUM FAN – INFINITUM AIRCORE
M-APL-DP-EC 03_12_24Page 2 of 4
INSTALLATION
1.Carefully remove the APL and any associated parts from its crate, use only approved lifting methods, units will be heavy.
2.Inspect the unit, make sure the fan wheel rotates freely. Inspect all hardware and fasteners, some may have loosened in shipping.
Make sure the unit is free of all foreign debris.
3.Units will be prepared with mounting locations through the venturi plate, and structural motor mount arms, use these to fasten the
unit in its installation position. . Figure 1
4.If you need to modify the unit for any reason to install it, do so under the supervision of a licensed mechanical contractor, or contact
Canarm before making any alterations.
5.Once the fan is secured, complete any ducting required in your system.
6.Make sure the motor, and its electrical compartment are free and clear and can be accessed in case of service.
7.When secure, remove the cover of the motor’s electrical compartment. All Wiring must be completed by qualified personnel only and
done in accordance with local codes.
8.Infinitum Aircore EC motor’s come equipped for variable speeds with an on board VFD.
9.Please review the Infinitum Installation, Operation and Maintenance manual linked on page 3 of this document.
10.Caution: Ensure all wiring or conduit is secured and cleanly restrained away from any rotating parts. Figure 2.
11.Caution: Always ensure branch power is locked out in the off position prior to performing any electrical work. Ensure power
supply matches the requirement of the motor, this will be labeled on the product.
12.When complete, Inspect the unit with qualified personnel prior to energizing the unit.
13.Once electrical connections are complete and inspected, replace the motor’s electrical compartment cover using the supplied hardware.
APL-DIRECT DRIVE EC SERIES
CANARM ARRAY PLENUM FAN – INFINITUM AIRCORE
M-APL-DP-EC 03_12_24Page 3 of 4
STANDARD WIRING DIAGRAMS
1.All wiring should be completed by a qualified electrician in accordance with National & Local Electrical Codes.
2.Ensure power supply is disconnected & the unit is locked out prior to performing any electrical work.
3.The unit’s motor has a large electrical compartment on the back of the motor.
4.Figure 5Refer to the Infinitum technical document linked below in this manual for specific wiring details. .
5.Excess wire as a result of service to the unit must be restrained cleanly, safely and kept away from rotating parts.
6.If excess wire needs to be cut, ensure you label all wire extensions prior to cutting.
7.Disconnect switches in close proximity to the unit are recommended in case the need arises to swiftly disconnect power.
8.Consult the Infinitum manual for specific motor requirements.
PRE-START INSPECTION
1.Set the main power breaker switch to “OFF” & lockout the power supply.
2.Check all fasteners on the unit and those that mount the unit to the installation structure. Some may have vibrated loose during shipping
or handling during set up.
3.Rotate the wheel to ensure that it rotates freely and nothing comes in contact with the housing. Note, this will generate current being a
Permanent Magnet motor.
4.Verify branch power, that your motor is wired and suitable for its supply. Failure may damage, or cause the motor to fail prematurely.
5.Check to ensure that all guards and accessories are securely mounted. If you guard the fan, ensure motor access remains and you do
not block the ventilation ports.
6.Once the unit’s hardware, and power supply are verified. You may proceed and test the unit. Remove power lockouts and proceed with
unit activation to ensure rotation direction is correctly set.
START UP
Turn the fan on and inspect for the following:
1.Any unusual sound or vibration.
2.Direction of wheel rotation
3.Improper motor amperage
If a problem is encountered, shut off the fan and refer to the section on troubleshooting, or the Infinitum manual linked above to discover the
cause of the problem. The fan should be inspected after 30 minutes, 8 hours & 24 hours of operation to ensure all fasteners are tight and the
unit is operating correctly.
FIGURE 5 - INFINITUM INSTALLATION, OPERATION & MAINTENANCE MANUAL
SCAN QR CODE OR VISIT LINK BELOW TO VIEW/DOWNLOAD INFINITUM MANUAL
https://support.goinfinitum.com/hc/en-us/articles/28039799952915-Aircore-EC-Installation-Operation-Maintenance-Manual
Product specificaties
| Merk: | Canarm |
| Categorie: | Niet gecategoriseerd |
| Model: | APL20-DP-EC |
Heb je hulp nodig?
Als je hulp nodig hebt met Canarm APL20-DP-EC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden