Calorex DH 75 Handleiding

Bekijk gratis de handleiding van Calorex DH 75 (4 pagina’s), behorend tot de categorie Ontvochtiger. Deze gids werd als nuttig beoordeeld door 57 mensen en kreeg gemiddeld 4.6 sterren uit 2 reviews. Heb je een vraag over Calorex DH 75 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Installation instructions

DH75/DH110 RANGE

Installation model DH75/110

1. Remove machine from packaging and set on a level surface.

Check at machine is level bo vertically and horizontally.

2. Remove covers as shown in FIG.1 relative to machine type

installed.

3. The Electrical supply to unit must be sized according to e

data on e serial number label, paying close attention to

I.E.E regulations latest edition regarding e special conditions

governing electrical supply to machines in potentially damp

areas (DH75/110 are IP45).

4. The electrical supply should be connected to e terminals

on e Printed Circuit Board in e electrical box found in

e top corner of e machine, see Fig1 & Fig4. Wires to be

connected as follows: brown/red to live, blue/black - to neutral,

and green/yellow to ear.The fan mode switch can be set

to cycle fan when Hygrostat senses demand but should be

set to continuous to promote good air circulation and reduce

condensation.

Note that on models fitted with LPHW and or remote hygrostat

the fans will start automatically whenever there is an air heating

or dehumidification demand. During defrost the fans will stop. (Fan

cycle not recommended for TTW machines with humidistat only).

Set Fan Speed switch to “High” for maximum duty, “Low” for minimum sound.

5. Locate drain, 15mm compression fitting, on side of unit and run

it away to waste as preferred. A single hole is provided in e

side of e unit. The drain is factory fitted to is hole. (In TTW

machines ere is an alternate position - see drawings).

Models wi LPHW fitted

6. Connect water circuit piping to e 22mm stubs provided on

e side of e machine as per diagram.

7. It is recommended at isolation valves are fitted to enable

isolation of e machine in e event of service.

The Circulating Pump must be sized to take into account

e design flow rate of e machine plus e water system

resistance. (Flow Rate 9.6 l/min Pressure Drop 2.8 m/hd).

Please leave ese instructions for e user.

Fig 1

Standard &

TTW machine

Standard

machine

Mains in

terminals on

printed circuit

board

Grille

Fixing screws (3)

Outer cover

Rremove panel

(4 screws)

Mains in

Condensate

drain

LPHW in

LPHW out

Port B

LPHW out

Port AB

LPHW in

Port A to LPHW fin

block

Fig 2

LPHW SCHEMATIC

Boiler

Radiator

(If fitted)

Flow

balance

valve

Flow meter

3 way motorised vslve

LPHW connections

located in cabinet

(Diverting)

Pump

Fig 3

DH75/110

Radaitor

(If fitted)

HEALTH & SAFETY WARNING

As e Heat Pump contains electrical and rotational equipment, it is recommended at ONLY competent persons carry out any work on is type of

machine (see guarantee). Isolate electrically before entering machine or removing panels.

This appliance is not intended for use by persons (including children) wi reduced physical,sensory or mental capabilities, or lack of experience and

knowledge, unless ey have been given supervision or instruction concerning use of e appliance by a person responsible for eir safety.

Children should be supervised to ensure at ey do not play wi e appliance

ISOLATE ELECTRICALLY BEFORE ENTERING MACHINE OR REMOVING PANELS.

The Calorex TTW units are designed for installation in a heated room, adjacent to e poolroom.

SD405450 issue 15

Product specificaties