Caliber Rally CA 4900 Handleiding

Caliber Autoradio Rally CA 4900

Lees hieronder de 📖 handleiding in het Nederlandse voor Caliber Rally CA 4900 (12 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
CA 4620 Rally
Ma x i m um Power Out put a t 1 4 ,4V
4Ω20Hz - 30kHz THD 1% 4x 120W
2Ω20Hz - 30kHz THD 1% 4x 155W
4Ω1kHz Mono Bridged 2x 310W
Co n t in u o us Power Out put a t 1 4 ,4V
4Ω20Hz - 30kHz THD 1% 4x 40W
2Ω20Hz - 30kHz THD 1% 4x 60W
4Ω1kHz Mono Bridged 2x 120W
Fus e Ra t ing 30A
D i m en s io ns 285x260x65mm
CA 4900 Rally
Ma x i m um Power O u t put a t 1 4 , 4 V
4Ω20Hz - 30kHz THD 1% 4x 225W
2Ω20Hz - 30kHz THD 1% 4x 225W
4Ω1kHz Mono Bridged 2x 450W
Co n t in u o us Power Out put a t 1 4 ,4V
4Ω20Hz - 30kHz THD 1% 4x 75W
2Ω20Hz - 30kHz THD 1% 4x 95W
4Ω1kHz Mono Bridged 2x 190W
Fus e Ra t ing 40A
D i m en s io ns 360x260x65mm
Alle Caliber Rally 4-kanaals versterkers hebben de
volgende technische gegevens. Technische gegevens die
per model verschillen zijn apart opgenomen.
Frequentierespons (+0, -1dB)20Hz-30kHz
Totale harmonische vervorming <0,05%
Signaal-ruisverhouding (A-Weighted) >103dB
Ingangsgevoeligheid RCA-ingang 3V - 200mV
Ingangsgevoeligheid High-Level ingang 10V - 2V
Laagdoorlaatfilter 80Hz
Variabele bassversterking 0dB- +6dB
Uitgangsimpedantie 2 - 8Ω
N E D E R L A N D S
All Caliber Rally 4-channel Amplifiers have the following
specifications.
Variable specifications are listed per model.
Frequency response (+0, -1dB)20Hz -30kHz
Total Harmonic Distortion <0,05%
Signal to noise ratio (A-Weighted) >103dB
Input Sensitivity RCA input 3V - 200mV
Input Sensitivity High Level input 10V - 2V
Low Pass Filter 80Hz
Variable Bass Boost 0dB - +6dB
Output Impedance 2 - 8Ω
NORMAL SYSTEM SET-UP
OPTIONAL SYSTEM SET-UP
Folgende technische Daten sind allen 4-Kanal-Verstärkern
vom Caliber Rally gemeinsam. Abweichende Werte sind
unter den einzelnen Modellen aufgeführt.
Frequenzgang (+0, -1dB)20Hz-30kHz
Gesamtklirrfaktor <0,05%
Rauschabstand (A-bewertet) >103dB
Eingangsempfindlichkeit Cinch-Eingang 3V - 200mV
Eingangsempfindlichkeit Hochpegel-Eingang 10V - 2V
Tiefpassfilter 80Hz
Variable Basshervorhebung 0dB- +6dB
Ausgangsimpedanz 2 - 8Ω
Alle Caliber Rally 4-kanals forsterkere har følgende spe-
sifikasjoner.
Variable spesifikasjoner listes opp for hver modell enkeltvis.
Frekvensrespons (+0, -1dB)20Hz-30kHz
Total harmonisk forvrengning <0,05%
Forhold mellom signal og støy (A-vektet) >103dB
Inngangsfølsomhet RCA-inngang 3V - 200mV
Inngangsfølsomhet høynivåinngang 10V - 2V
Lavpassfilter 80Hz
Variabel basshevning/senking 0dB- +6dB
Utgangsimpedans 2 - 8Ω
Todos los amplificadores Caliber Rally 4-canales tienen las
siguientes características.
Para cada modelo se indican las características variables.
Respuesta de frecuencia (+0, -1dB)20Hz-30kHz
Distorsión armónica total <0,05%
Media señal-ruido (ponderada en A) >103dB
Entrada Input Sensitivity RCA 3V - 200mV
Entrada Input Sensitivity High level 10V - 2V
Filtro de paso bajo 80Hz
Compensador de Bajos Variable 0dB- +6dB
Impedancia de salida 2 - 8Ω
Tous les amplificateurs Caliber Rally à 4 canaux possèdent
les caractéristiques ci-dessous. Les caractéristiques
variables sont définies pour chaque modèle.
Réponse en fréquence (+0, -1dB)20Hz-30kHz
Distorsion harmonique totale <0,05%
Rapport signal/bruit (pondéré A) >103dB
Sensibilité d'entrée Entrée Cinch 3V - 200mV
Sensibilité d'entrée haut niveau 10V - 2V
Filtre passe-bas 80Hz
Accentuation variable des graves 0dB- +6dB
Impédance de sortie 2 - 8Ω
Tutti gli amplificatori Rally a 4 canali della Caliber hanno le
seguenti specifiche tecniche.
Le specifiche tecniche variabili sono elencate per modello.
Risposta in frequenza (+0, -1dB)20Hz-30kHz
Distorsione armonica totale <0,05%
Rapporto segnale/rumore (pesato 'A') >103dB
Sensibilità di ingresso RCA 3V - 200mV
Sensibilità di ingresso High-level 10V - 2V
Filtro Low-Pass 80Hz
Enfatizzazione bassi variabile 0dB- +6dB
Impedenza di uscita 2 - 8Ω
Todos os amplificadores Caliber Rally 4-canais têm as
seguintes características.
Para cada modelo indicam-se as características variáveis.
Resposta de frequência (+0, -1dB)20Hz-30kHz
Distorção harmónica total <0,05%
Média sinal-ruído (ponderada em A) >103dB
Entrada Input Sensitivity RCA 3V - 200mV
Entrada Input Sensitivity High Level 10V - 2V
Filtro de passagem baixa 80Hz
Compensador de Baixos Variável 0dB- +6dB
Impedância de saída 2 - 8Ω
E N G L I S H
E S P A Ñ O L P O R T U G U Ê S
S V E N S K
D E U T S C H I T A L I A N O
F R A N C A I S
4
E N G L I S H
3
E N G L I S H
2
H I G H L E V E L I N P U T
• Connect the loudspeaker outputs of your radio to the wires which are already on the special plug
you found in the box.
Ta ke good care of the polarity (+ or -), and which signal is right or left.
L- = White, L + = White/Black R- = Gray, R + = Gray/Black GND = Black, connect
to Ground.
R C A I N P U T
• Connect the RCA-outputs of your radio to the RCA input terminals of the amplifier.Take good care
that you connect the Right output of your radio to a Right input of your amplifier, and that you
connect the Left output of your radio to a Left input of your amplifier.
S P E A K E R O U T P U T
• All the Caliber Rally amplifiers have Stereo/Bridgeable Tri-Mode speaker output terminals. The
amplifier has its own stereo/bridge switch built-in, so there is no need to select a stereo or bridged
mode.You can connect the speakers to each channel in stereo mode, and simultaneously connect
a sub-woofer to the speaker terminal in a bridged mode.
• Pay attention in connecting your speakers and/or sub-woofers. Be sure to observe correct speaker
output connections for front, rear and their polarity.
In the stereo mode, connect the right speaker output to the right speaker and the left to the left.
Connect the positive (+) output to the positive (+) speaker terminal and the negative (-) output
to the negative (-) speakerterminal.
• In the bridged mode connect the left (+) positive to the positive speaker terminal and the right (-)
negative to the negative speaker terminal.
• Do not use the negative speaker output commonly for left and right speakers (common ground).
Improper polarity causes a loss of bass response.
• Never connect the negative speaker output to the chassis of your vehicle. This can cause severe
damage to your Car Audio System.
A M P L I F I E R A D J U S T M E N T S
You will get the best result if you adjust the front and rear channels separately.
• Unplugg the input for the rear channel and start with the front channel.
• Put the input level adjustment knob to the minimum.
• Put the volume of your radio to 3/4 of the maximum.
• Now adjust the input level of the front channel. Slowly turn up the input level and listen carefully
untill you hear the amplifier begin to distor t. A Caliber Amplifier “clips” very softly, so this can
sometimes be a difficult adjustment.
• Once the front channel is fine-tuned to your satisfaction, you can plugg in the input for the rear
channel and unplugg the front channel input. Repeat the adjustments as we described them here above.
• Plugg in the front channel input again, and let your amplifier play on both the front and rear channels.
Listen once again very carefully if your front and rear channels are harmoniously playing together,
and make some final adjustments if necessary.
C A L I B E R W A R R A N T Y
Due to the complexity of our products, we strongly recommend that this amplifier is installed
by your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for
12 month from the date of purchase.
If you install this amplifier yourself, we wish you lots of fun and succes in doing so. If you follow
our guidelines, you’ll get the best result.Our warranty, however, will be limited to and not exceed
30 days from the date of purchase.
F E A T U R E S
• Bridgeable outputs.
• ’Tri-mode’ output capability, simultaneous stereo & bridged mono set up is possible.
• Pulse Width Modulated (PWM) MOSFET Power Supply.
• Variable input sensitivity: RCA input 0.2V to 4V.
• Variable input sensitivity: High Level input 2V to 10V.
• Thermal-, Overlaod- and Shortcircuit protection.
• Excellent muting circuitry assures no turn on/off ‘pops’.
• Built-in Full Range/High Pass Switch on channel 1and 2.
• Built-in Full Range/Low Pass Switch on channel 3 and 4.
• Chromium plated power connectors for optimal power distribution.
• European design and engineering.
• Chromium plated speaker connectors for optimal signal output.
M O U N T I N G
The amplifier has to have at least 5cm (2”) ventilation space at all sides, to allow the heat to rise
away from the amplifier. Be sure that the power and signal cables can enter and leave the amplifier
in a straight line, to avoid the risk of malfunction. Always place the power- and signalcables at
opposite sides of the vehicle to reduce any noises.
The amplifier should be protected from exposure to moisture and direct sunlight.
Mark the mounting surface using the amplifier as a template, then drill 2.5mm (1/8”) diameter holes
at the marked locations and mount the amplifier using the supplied self-tapping screws.
I N S T A L L A T I O N
Remember to always disconnect battery ground before working on a vehicle’s electrical system!
Always place a fuse or circuit breaker no more than 30cm (12”) from the batter y, no greather than
the fuse(s) of your amplifier for optimal protection.
G E T T I N G Y O U R P O W E R S T A R T E D
• First, the +12V terminal is connected directly to the batter y of your car. Use a cable of at least
10mm2 (8 AWG), and make sure that the connectors are of the same value.
Don’t forget the extra “Vehicle protection” fuse.
The 12V + terminal should NOT be connected to the car fuse box.
• Second, the ground terminal (GND) must be fastened securely to the chassis of the vehicle with the
same gauge cable as the positive cable (the same amount of power has to run through it). Ensure
that all paint, undercoating or any other insulation is removed from the area where you want to
make your ground connection to.
• Third, the last cable to connect is your remote turn-on (REM). Many radio-cassette and CD-players
have an output terminal for connection of the REM of an amplifier. If you don’t have such an out-
put, a separate switch must be installed to control your amplifiers on/off function.
S I G N A L I N P U T
The Caliber Rally Amplifiers offer you two possibilities for your signal input.
• A High Level input, using the loudspeaker output from your radio and the special High Level input-
plug you found in the box.
• Signal input by using a RCA cable from your radio’s RCA outputs to the amplifiers signal input
RCA’s.
NEVER USE HIGH LEVEL INPUT AND RCA INPUT AT THE
SAME TIME

Product specificaties

Merk: Caliber
Categorie: Autoradio
Model: Rally CA 4900

Heb je hulp nodig?

Als je hulp nodig hebt met Caliber Rally CA 4900 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Autoradio Caliber

Caliber

Caliber RCD 239DAB-BT Handleiding

4 Augustus 2023
Caliber

Caliber RMD 806BT Handleiding

19 Juni 2023
Caliber

Caliber RCD120DAB-BT Handleiding

18 Juni 2023
Caliber

Caliber RMD056DAB-BT Handleiding

13 Juni 2023
Caliber

Caliber CA 75 2 Handleiding

7 Juni 2023
Caliber

Caliber CA 2260 Handleiding

10 Mei 2023
Caliber

Caliber RMD402DAB-BT Handleiding

5 Mei 2023
Caliber

Caliber RMD055 Handleiding

3 Mei 2023
Caliber

Caliber MCD263BT Handleiding

30 April 2023
Caliber

Caliber RMD213DAB-BT Handleiding

29 April 2023

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio

Alpine

Alpine SWC-W84CRA2 Handleiding

9 April 2024
Alpine

Alpine SWC-D84DU Handleiding

9 April 2024
DLS

DLS CAD15 Handleiding

5 April 2024
DLS

DLS A3 Ultimate Handleiding

5 April 2024
DLS

DLS CAD11 Handleiding

5 April 2024
DLS

DLS RA40 Handleiding

5 April 2024
Macrom

Macrom SP2.050 Handleiding

31 Maart 2024
Macrom

Macrom M-DVD7601 Handleiding

31 Maart 2024
Macrom

Macrom M3A.250 Handleiding

31 Maart 2024
Macrom

Macrom Syn Power 4.050 Handleiding

31 Maart 2024