Caliber PARK 500 Handleiding
Caliber
Niet gecategoriseerd
PARK 500
Bekijk gratis de handleiding van Caliber PARK 500 (11 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 308 mensen en kreeg gemiddeld 4.7 sterren uit 154.5 reviews. Heb je een vraag over Caliber PARK 500 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/11
E N G L I S H
1
PARK 500 PARKING SENSOR SYSTEM
PARK 500 consists of ultrasonic sensors, camera and digital control
box. (Besides these, a outer connected display with RCA plug is
needed).The video signal is inputted into control box via VIN (video
Input) and processed by control box, then outputted to outer
connected display with RCA plug via VOUT (Video Output). This
system detects the distance between the car and back obstruction
by ultrasonic sensors fixed at rear bumper of the car, and the display
shows the back image via the camera fixed at the rear of the car.
With the change of alarm sound, figure or simulation bars as well as
the image, the driver could judge the distance to avoid accident.
INSTALLATION TOOLS
ADVISED POSITION TO INSTAL THE SENSORS
SELECT DRILLING POSITION FOR SENSOR A AND D
A B E C D
Ø 21 mm
for sensor
Ø 25 mm
for camera
A. 4 drilled holes (A, B, C, D) and camera hole
(E) should be under the same line
B. 0.5-0.8m vertically high to the ground, 0.55m
is recommended
C.Vertical, tidy surface without metal
components is preferred.
A. Choose suitable drilling position for A and D
sensor with relevant mark
E N G L I S H
2
SELECT DRILLING POSITION FOR SENSOR AND CAMERA B,C AND E
DRILLING
SENSOR AND CAMERA INSTALLATION
B.To perform the best detecting angle, select the
position for A and D sensor with 8-13cm away
from the side, 11cm is recommended, and 20°
with the side.
A.Measure the distance between sensor A and D,
get the result “L”.
B.Mark sensor B, C and E for every 1/4 “L”
interval. (Camera E should be in the middle of
the bumper)
A.Firstly, use a small driller tip to locate.
B.Drill with the original driller. Ø21MM
DRILLER FOR SENSOR HOLES AND
Ø25MM DRILLER FOR CAMERA HOLE.
A.Insert the sensors and camera into the holes
one by one and tighten them, the sensor with
metal slice must be up and down fixed instead
of right and left.The camera must be fixed with
the triangle mark upward.
B.Hide the wires in good order according to
various cars.
E N G L I S H
4
SENSOR DETECTING
SENSOR AND CAMERA INSTALLATION DIAGRAM
The direction of sensors
DETECTING RANGE
1.5m
90° 90° 90°
Camera
Sensor
0.6 - 0.8m 0.3 - 0.4m
The best postiton for 2 sensors The best postiton for 4 sensors
Notice: Fix the camera in the
middle of bumper on the same
level with sensors.
0.5 - 0.8m
Vertical installation position to the ground.
Sloping installation position to the ground.
Top view Side view
Product specificaties
| Merk: | Caliber |
| Categorie: | Niet gecategoriseerd |
| Model: | PARK 500 |
Heb je hulp nodig?
Als je hulp nodig hebt met Caliber PARK 500 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Caliber
11 Juni 2023
9 Juni 2023
3 Juni 2023
2 Juni 2023
18 Mei 2023
9 Mei 2023
1 April 2023
31 Maart 2023
23 Maart 2023
22 Maart 2023
Handleiding Niet gecategoriseerd
- Rome
- OJ ELECTRONICS
- Alto
- Draytek
- Homelite
- Blackmagic Design
- Octavio
- Vileda
- Hapro
- Beghelli
- Pontec
- Gehmann
- ESKA
- Woood
- Savage Bros.
Nieuwste handleidingen voor Niet gecategoriseerd
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025