Boston Acoustics Sub10F Handleiding


Bekijk gratis de handleiding van Boston Acoustics Sub10F (6 pagina’s), behorend tot de categorie Subwoofer. Deze gids werd als nuttig beoordeeld door 57 mensen en kreeg gemiddeld 4.3 sterren uit 29 reviews. Heb je een vraag over Boston Acoustics Sub10F of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Pagina 1/6
In-Floor Subwoofer
Sub10F
Introduction
In many homes and installations, the deep bass of a powered subwoofer is desired, but often there is
not a suitable location to install a box subwoofer. The Boston Sub10F In-Floor Subwoofer handily solves
this dilemma. Located below the oor and powered by the companion Boston SA1 Subwoofer Power
Amplier, all that is visible in the listening room is a oor register.
Warning: Always turn off the amplier when connecting the subwoofer and any other components to
Note: The Sub10F is an installed product. Installation should only be attempted by professional
installers or those possessing skills in construction, the proper use of hand and power tools, knowledge
of local building and re codes, and a familiarity with the environment below the oor in which the sub-
woofer will be installed.
Placement
For maximum bass, place the Sub10F so its vent is near a corner or sidewall and is as close to the main
speakers as possible.
Floor Register (Not supplied)
The Sub10F mounts in the oor directly below a oor register. The register should have a minimum air
opening of 3 x 9". Return registers without moving parts should be used. If the register has moving lou-
vers or other moving parts, they will need to be removed to prevent them from rattling.
Floor Thickness
As oors differ in thickness, it is important to measure the depth of the oor register and the thickness
of the oor to conrm that the oor register will not be in contact with the subwoofers grille.
2
Location Hazards
It is the nature of low-frequency energy (bass) to make objects vibrate. Care should be taken in planning
the installation of the in-oor subwoofer to minimize the risk of room vibration and noise. Do not locate
the in-oor subwoofer close to lamps or furniture that might rattle or vibrate. Some bass energy will be
heard in the room below the subwoofer. If the ceiling below is nished, ceiling xtures may rattle or
vibrate.
It is recommended that in the area where the Sub10F is to be mounted, the suboor is glued to the
joists and extra nails are used to secure the suboor. Be sure the joists to which the Sub10F is mounted
are securely braced against each other so that the distance between them does not change and they
are not able to move or shift (consult local building codes)
Amplier Requirements & Wiring
The Sub10F must be used with the Boston SA1 Subwoofer Power Amplier. Use with any other amplier
will result in poor performance. One SA1 Power Amplier can power up to two Sub10F subwoofers.
Only one Sub10F should be connected to each set of terminals on the SA1. If you are installing only one
Sub10F, pre-wire so that a second one can be added, but do not connect the extra set of speaker wires
to the SA1.
Set the equalization switch (EQ-MODE) on the back of the SA1 amplier to the position. WeFLOOR
recommend the use of 16-gauge or larger speaker wire with both the Sub10F and SA1.
Service Access
If service is needed, the Sub10Fs woofer can be removed through the access panel on the bottom of
the subwoofer. If there is a nished ceiling below the Sub10F, ideally a door allowing access to the
complete subwoofer enclosure, or at minimum, to the Sub10Fs service panel, should be left in the ceil-
ing below.
3


Product specificaties

Merk: Boston Acoustics
Categorie: Subwoofer
Model: Sub10F

Heb je hulp nodig?

Als je hulp nodig hebt met Boston Acoustics Sub10F stel dan hieronder een vraag en andere gebruikers zullen je antwoorden