Boss MR1620 Handleiding

Boss Autoradio MR1620

Lees hieronder de đź“– handleiding in het Nederlandse voor Boss MR1620 (21 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/21
CONTENTS
MR1620W • MR1620S User’s Manual - page 1
U S E R ’ S M A N U A L
MR1620W • MR1620S User’s Manual - page 2
Head unit installation
MR1620W • MR1620S Marine MP3/CD Receiver Packing List
To ensure tha
meets the IPX
Standard, plea
carefully.
1. Remove the
the top of the
beginning the
Fig 1 R
2. Place the tw
provided over
prevent water
Figure 2 Apply
Before installing your new CD Receiver, please unpack the contents and check
that your package contains the following items:
2Head unit installation
4Detaching the front panel
5Removing the head unit
6Remote control installation
Flush mount
6Remote control installation
Surface mount
10 General and tuner controls
14 Remote control
15 CD Playback
15 MP3 playback
16 RDS radio functions
17 PTY station categories
18 Wiring diagram
19 Troubleshooting
20 Specifications
Congratulations on your
purchase of a Marine
MP3/CD Receiver.
It has been designed, engineered
and manufactured to bring you
the highest level of performance
and quality, and will afford you
years of listening pleasure.
Thank you for making
Marine your choice for
marine audio entertainment!
Main unit
Detachable front panel with protective case
Mounting hardware for main unit:
Rear bracket plate
Rear mounting screw
Plain washer
Spring washer
Screw
Hex nut
Removal keys (2)
Wiring harness
Wired remote control
Remote control cable
Mounting hardware for remote control:
Mounting arms (2)
Mounting tube (1)
Machine screws (2)
User’s manual
Warranty card
MR1620W
MR1620S
Fully Mariniz oed MP3-C mpatible
In-Dash CD Receiver
page
RDS Model with
Switchable U nSA/Europea
Frequencies
MR1620W • MR1620S User’s Manual - page 2
Head unit installation
MR1620W • MR1620S User’s Manual - page 3
Before installing your new
CD Receiver, please become familiar
with all the information contained in
this manual.
Choose a mounting location where the
unit will not distract or otherwise
interfere with the pilot’s ability to control
the boat.
Use only the installation parts and
hardware provided with the unit to
ensure proper installation. Using other
parts can cause malfunction and
possible damage to your CD
receiver.
Do not install this unit at an angle in
excess of 30Âş from horizontal, as it
may affect performance.
Although this unit has been designed
for outdoor use, you can extend its life
if you install it in a location which is
not subject to extreme temperatures,
from such sources as heaters or
exhaust lines. Also, if you see dirt, dust
or debris on a disc or in the CD slot,
remove it with a clean cloth to avoid
pushing it into the player mechanism.
To remove dirt from the faceplate, use
a clean cloth lightly moistened with
filtered water. If the unit is splashed
with water, wipe it off with such a clean
damp cloth before the water has dried
to avoid an accumulation of salts on
the face of the unit.
If properly installed, this unit will meet
the IPX5 Waterproof standard. Please
note that this does NOT mean the unit
is submersible, but will resist being
sprayed and splashed as might occur
in a normal boat cabin.
To ensure that the installation
meets the IPX5 Wat oerpr of
Standard, please follow these steps
carefully.
1. Remove the transport screws from
the top of the enclosure before
beginning the installation.
Fig 1 Remove transport screws
2. Place the two pieces of plastic film
provided over the two screw holes to
prevent water penetration.
Figure 2 Apply plastic film to seal screw holes
Figure 3 Bending the support tabs
3. Insert and tighten the “headless”
support screw into the back of the
head unit where shown.
4. Insert the mounting case for the
head unit into the dashboard. Inspect
the dashboard material to determine
its approximate thickness. Select the
appropriate support tabs and bend
them outward to secure the bracket
in place .(Figure 3)
5. Bend the backstrap to conform to
the mounting case and the dashboard
surface to which you plan to secure
the backstrap (Figure 4). Slide one of
the utility holes on the backstrap onto
the support screw and fasten it with
the spring washer and nut provided.
6. Using the 5 x 25mm screw and the
plain washer, secure the backstrap to
the dashboard surface as shown in
the diagram. Tighten, secure, and
check the overall mounting to be sure
it is safe and will not release in an
emergency stop or other sudden
movement of the vehicle.

Product specificaties

Merk: Boss
Categorie: Autoradio
Model: MR1620

Heb je hulp nodig?

Als je hulp nodig hebt met Boss MR1620 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Autoradio Boss

Boss

Boss BVD9988B Handleiding

24 Maart 2024
Boss

Boss BVCP9800W Handleiding

24 Maart 2024
Boss

Boss BCPA8W Handleiding

24 Maart 2024
Boss

Boss Elite BEHDIN98 Handleiding

8 December 2023
Boss

Boss ATV654 Handleiding

23 November 2023
Boss

Boss ATVB6.5R Handleiding

9 November 2023
Boss

Boss BV7320 Handleiding

27 Juni 2023
Boss

Boss MR648S Handleiding

21 Juni 2023
Boss

Boss BVB9351RC Handleiding

20 Juni 2023
Boss

Boss 775DI Handleiding

19 Juni 2023

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio

Alpine

Alpine SWC-W84CRA2 Handleiding

9 April 2024
Alpine

Alpine SWC-D84DU Handleiding

9 April 2024
DLS

DLS CAD15 Handleiding

5 April 2024
DLS

DLS A3 Ultimate Handleiding

5 April 2024
DLS

DLS CAD11 Handleiding

5 April 2024
DLS

DLS RA40 Handleiding

5 April 2024
Macrom

Macrom SP2.050 Handleiding

31 Maart 2024
Macrom

Macrom M-DVD7601 Handleiding

31 Maart 2024
Macrom

Macrom M3A.250 Handleiding

31 Maart 2024
Macrom

Macrom Syn Power 4.050 Handleiding

31 Maart 2024