Bogen Nyquist NQ-S1810CT-T1 Handleiding
Bogen
Niet gecategoriseerd
Nyquist NQ-S1810CT-T1
Bekijk gratis de handleiding van Bogen Nyquist NQ-S1810CT-T1 (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 6 mensen en kreeg gemiddeld 4.6 sterren uit 3.5 reviews. Heb je een vraag over Bogen Nyquist NQ-S1810CT-T1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
Specications are subject to change.
© Copyright 2022–2023, Bogen Communications LLC
740-00156D 230316
NQ-S1810CT-T1 VoIP Ceiling Speaker
Installation and Use Guide
2
NQ-S1810CT-T1
With the Nyquist S1810CT-T1 VoIP Ceiling Speaker, there is no need for external ampliers, traditional intercom
wiring, or transformer taps to manually set or adjust. Connect the speaker via Cat5-or-better cabling to a Pow-
er-Over-Ethernet (PoE) Switch or PoE Injector, and it is ready to use.
The speaker features an integrated 10W power amplier, a CAN Bus interface, a MEMS digital microphone for su-
perior talkback audio, a 25V- or 70V-output-capable transformer for supporting up to four additional loudspeakers
*
,
and a Form C SPDT-type 2A dry-contact relay for controlling/overriding third-party devices like AV sources.
*
Note: The secondary 25V/70V loudspeakers do not support talkback.
The speaker also allows DHCP deployment for easy installation. You can let your Nyquist server automatically dis-
cover and congure your speaker, or you can manually congure it through the speaker’s web-based user interface
(web UI). The web UI also allows easy updating of rmware and setting of parameters for Digital Signal Processing
(DSP). For more information about the web UI, refer to the Nyquist Gen-2 VoIP Speakers Conguration Manual.
Speaker Layout
The layout of the speakers should be planned before installation begins. Layout starts in one corner of the room.
The rst speaker should be positioned from each wall spaced a distance approximately equal to the ceiling height
of the room.
The next speaker in row 1 should be spaced a distance approximately equal to twice the height of the ceiling. Each
additional speaker in the row should use this same spacing.
Row 2 starts at twice the ceiling height distance from row 1 and twice the ceiling height from the wall. The other
speakers in this row are also spaced at twice the ceiling height.
Row 3 is again spaced at twice the ceiling height from the previous row. The rst speaker starting this row is posi-
tioned at one ceiling height distance from the wall (similar to row 1).
Continue this pattern of alternating rows until the room is covered. The spacing of the speakers can be adjusted so
that the speakers are evenly spaced in a row and are aesthetically pleasing.
3
NQ-S1810CT-T1
RE84 Recessed Enclosure
The RE84 is an optional back box for ceiling speakers. UL Listed for use where ceiling ple-
num is part of an air handling system, the RE84 also includes attachment tabs, allowing
the enclosure to be supported from structures other than the actual ceiling grid.
TB8 Tile Bridge
The TB8 supports the weight of the speaker and recessed enclosure. This is also the
item to which the speaker mounting screws attach. The TB8 is required for each speak-
er assembly installed.
MR8 Mounting Ring
The MR8 Mounting Ring is a cold-rolled steel unit, which will mount any of the Bogen ceiling
grilles for installations where the RE84 is not used.
Speaker Installation
1. Remove the tile from ceiling and center the TB8 tile bridge on the back. Use the tile bridge
to trace out and then cut an 8½” square hole.
Note: It may be more ecient to stack multiple ceiling tiles and then cut the speaker opening in a number of them
at one time.
2. If using the optional RE84 Recessed Enclosure, bend up the four horseshoe tabs (Figure 1) on the TB8.
3.
Figure 1
Position the TB8 over the hole in the tile and push down the locator tabs
4. Using the four supplied screws, attach the speaker to the TB8
using the four clips in the corners of the opening on the TB8 as
nuts.
NOTE: Only tighten the screws until the grille is snug against the
tile. Over-tightening will cause the screws to dimple the grille.
5. When applicable, use the pluggable CAN bus connector to
attach one or more NQ-E7020-G2 Digital Call Switches to the
Nyquist VoIP Module 820-00071-00, as shown in Figure 3.
Figure 2
Product specificaties
| Merk: | Bogen |
| Categorie: | Niet gecategoriseerd |
| Model: | Nyquist NQ-S1810CT-T1 |
Heb je hulp nodig?
Als je hulp nodig hebt met Bogen Nyquist NQ-S1810CT-T1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Bogen
15 Juni 2025
15 Juni 2025
15 Juni 2025
23 Mei 2025
22 Mei 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
Handleiding Niet gecategoriseerd
- Toolcraft
- Adonit
- Technisat
- Clas Ohlson
- LandRoller
- Moleskine
- Truelife
- Hario
- HyperJuice
- Neunaber
- BMW
- Urbanista
- Elica
- SoundSwitch
- EKO
Nieuwste handleidingen voor Niet gecategoriseerd
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
18 Juni 2025