Bobrick B-3725 Handleiding
Bobrick
Handendroger
B-3725
Bekijk gratis de handleiding van Bobrick B-3725 (4 pagina’s), behorend tot de categorie Handendroger. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 4.7 sterren uit 3 reviews. Heb je een vraag over Bobrick B-3725 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
Form No. 3725-69 (Issued 9/21/16) © 2016 Bobrick Washroom Equipment, Inc.
INSTALLATION INSTRUCTIONS
Recessed Hand Dryer
B-3725 115V / 230V
1
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Form No. 3725-69 (Issued 9/21/16) © 2016 Bobrick Washroom Equipment, Inc.
2
Distance from fl oor to bottom mounting screw holes of mounting base.
Children's Washrooms, ages 3-4 ..............................................................................................................................................................36'' (915mm)
Children's Washrooms, ages 5-8 ..............................................................................................................................................................40'' (1015mm)
Children's Washrooms, ages 9-12 ............................................................................................................................................................44'' (1120mm)
Universal Design 40'' - 48'' (1015 x 1219mm) ..................................................................................................................................................................
Bobrick automatic hand dryers should be installed at least 15" (380mm) above any projection or horizontal surface which may interfere with the
operation of the automatic sensor.
Model ADA Recessed Hand Dryer B-3725 115V, 8.5 Amp, 1000 Watts, 50/60 Hz, Single Phase, cULus listed.
Model ADA Recessed Hand Dryer B-3725 230V, AC, 4.0-4.4 Amp, 1000 Watts, 50/60 Hz, Single Phase; cULus listed and CE marked.
Installation instructions and template provide information that will assist in the installation of the Bobrick B-3725 115V / 230V. Retain Installation
Instruction Sheet for important maintenance instructions and warranty information.
Warm air hand dryer is intended for use in an indoor environment by non-expert users. This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision. Electronic automatic dryer sensor will pick up movement within 4" (100mm)
of the air outlet opening.
Installation and wiring must conform to current local regulations and building codes. Unit must be installed by
a qualifi ed electrician. Turn off electrical power supply before making electrical connections. If the unit fails or
malfunctions, it should be disconnected from the power supply and a qualifi ed electrician should be called.
Provide framed rough wall opening 10-7/8" wide x 23" high (277mm x 585mm). Minimum recessed depth required to fi nish face of wall
is 4" (100mm). Allow clearance for construction features that may protrude into rough wall opening from opposite wall. Coordinate with
mechanical engineer to avoid pipes, vents and conduits. If unit projects above top of wainscot, provide channel or other fi ller to eliminate
gap between cabinet fl ange and fi nish face of wall.
1. Loosen dryer cover by removing
the mounting screws located at
the bottom of the unit using a
Torx T20 bit. (See Fig. 1)
2. Pull bottom side of dryer cover
forward and lift up carefully to
disengage dryer cover. (See Fig. 1)
4. Slide absorbent ceramic surface
forward and out of cabinet and set
aside. (See Fig. 3)
5. Provide electrical service
from nearest distribution
panel to dryer mounting base
in conformance with local
electrical codes. Use wire as
required by local electrical code,
No. 12 (3.31mm² dia.) wire or
larger. (See Fig. 4)
3. Unplug the sensor wires from
dryer to separate dryer cover from
cabinet and set aside. (See Fig. 2)
Electrical Characteristics
Recommended Mounting Heights
Installation of Cabinet
Safety Warning
Important Notes
Fig. 5
Fig. 6
Form No. 3725-69 (Issued 9/21/16) © 2016 Bobrick Washroom Equipment, Inc.
3
6. Mount unit into wall opening with
shims between framing and
cabinet at screw hole locations.
7. Secure using #8x1-1/4'' (4.2 x 32mm)
sheet metal screws (not
furnished). (See Fig. 6)
8. Insert absorbent ceramic into
place. Make sure ceramic is fully
inserted so that it does not
interfere with the dryer cover.
9. Connect activation sensor wires
to dryer.
10. Replace dryer cover by engaging
the top side fi rst, then secure with
screws.
1. Turn electrical power supply on.
2. Wait until activation sensor light fl ashes green.
3. Position hands under air outlet, within (4") of air outlet opening.
4. Dryer should turn on. Warm air should blow from air outlet.
5. Remove hands from under air outlet and dryer should stop (within 2 seconds).
WARNING: MOTOR LAMINATIONS ARE LIVE. TURN ELECTRICAL POWER SUPPLY OFF BEFORE DOING ANY MAINTENANCE OR SERVICE
TO DRYER. DRYER MUST NOT BE OPERATED UNLESS COVER IS IN PLACE.
FOR PROPER ELECTRICAL CONNECTIONS, CHECK LOCAL BUILDING CODE. UNIT MUST BE INSTALLED BY A QUALIFIED LICENSED
ELECTRICIAN
1. Exterior of cover should be cleaned with a damp cloth to remove dust and surface dirt. Do not use abrasive agents or solvents as they may
permanently damage surface of cover.
2. At least once every 6 months remove cover. Using a small brush or vacuum, clean out buildup of dust and lint from air-intake grille and baffl e.
NOTE: if dryer is installed where there is a lot of dust and dirt in the air, the interior of the dryer should be cleaned out more frequently
Replacement Parts:
Absorbent Material 3725-23
Door 3725-53
Motor Brushes 700-121.
a. Electrical supply entry holes are
located in the rear and
sides of cabinet. Supply cable with
supplementary insulation into one
of these locations in the unit cabinet.
Cabinet should be fi tted with a
conduit connection. Plastic grommet
supplied to use as necessary.
b. This appliance is intended for
connection to fi xed wiring.
c. A fused means for disconnection in
all poles must be provided in the
fi xed wiring in accordance with the
wiring rules.
d. Check that the electrical rating
shown on the dryer (rating label) is
compatible with the electrical supply.
e. WARNING: THIS PRODUCT MUST
BE GROUNDED (EARTHED).
f. For 115–Volt Dryers, connect
ground wire to ground terminal
marked
, the black or hot wire
to terminal marked L1, and neutral
or white wire to terminal marked N.
A DEDICATED LINE IS REQUIRED
FOR EACH 115-VOLT
INSTALLATION. (See Fig. 5)
g. For 208–240 Volt Dryers, connect
ground wire to ground terminal
marked
and the 208–240 volt
wires to terminal marked L1 and L2.
(See Fig. 5)
Check Dryer Operation
Maintenance
Installation of Cabinet (cont.)
Product specificaties
| Merk: | Bobrick |
| Categorie: | Handendroger |
| Model: | B-3725 |
Heb je hulp nodig?
Als je hulp nodig hebt met Bobrick B-3725 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Handendroger Bobrick
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
11 Augustus 2023
11 Augustus 2023
11 Augustus 2023
11 Augustus 2023
Handleiding Handendroger
- Mitsubishi
- Biodrier
- Noirot
- American Dryer
- Dyson
- Stiebel Eltron
- Lavex
- Uniprodo
- Dimplex
- Hamilton Beach
- Honeywell
- Hendi
- Starmix
- Bradley
- Royal Sovereign
Nieuwste handleidingen voor Handendroger
11 Juni 2025
10 Juni 2025
15 Oktober 2024
14 November 2023
5 Juli 2023
28 Juni 2023
28 Juni 2023
25 Juni 2023
25 Juni 2023
21 Juni 2023