BlendMount BCB-2121 Handleiding
BlendMount Niet gecategoriseerd BCB-2121
Bekijk gratis de handleiding van BlendMount BCB-2121 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 71 mensen en kreeg gemiddeld 4.8 sterren uit 7 reviews. Heb je een vraag over BlendMount BCB-2121 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
PART# BCB-2121
Blencl.
fflounf-®
&cobra
·
l
llJJJ
IJIR!ll
5
Innovative
Mounting
Solutions
LEFT HAND DRIVE VEHICLE
INSTALLATION INSTRUCTIONS FOR THE
COBRA
DSP-9200BT, SPX-7800BTn700, SPX-6700, AND IRAD 900
RADAR
DETECTOR
Your rear view
mirror
has minimal clearance between the back side
of
the
mirror
and the
mirror
stem. It
is
very
im-
portant
that
this
mount
is
installed correctly
to
ensure
mirror
adjustability
is
retained.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT
NOTE: For illustration purposes, the
mount
and rear view
mirror
shown in these instructions may
look
slightly different then YOUR mount and rear view mirror.
OPPOSING FORCES
1 -The RELEASE Button on the radar detector (RD) Is NOT used with this mount.
To
release the tension
of
the spring clip, simply squeeze the TRIGGER and the back side
of
the mount together. This will lower the bottom portion
of
the spring clip allowing you to
slide the RD on and off. When used properly, the spring clip avoids putting excessive
pressure on the mirror stem when installing and removing the RD. The top portion
of
the mount should barely move when the two opposing forces are applied.
TOP
SECTION
___
.._
,._,..,.
TOP AND MID
SECTIONS MUST TOUCH
AT THE
PIVOT
POINT
BEFORE CLAMP SCREW
IS FULLY TIGHTENED
3 -Loosen the clamp screw so the top section separates from the mid section. This will
provide the necessary clearance to slide the mount over the mirror stem as shown above.
Adjust the mirror parallel to the windshield for ease
of
installation. As you are tightening the
clamp screw, make sure the top and mid sections touch at the pivot point. If they do not
touch at th p vot point, this mount Is incompatible with your mirror type. Tighten the
clamp
screw until the mount is slightly snug around the mirror stem.
BOTTOM OF SPRING CLIP
IS PARALLEL WITH RD
2 • The bottom
of
the spring clip
must
be parallel with the
top
of
the RD to slide in and out. SLIDE THE RD ONTO
THE SPRING CLIP AS FAR AS IT WILL GO. Release the
trigger to secure the RD onto the mount. Before installing the
mount onto your rear view mirror, remove and install the RD a
few times so you can observe how the spring clip functions.
4 -Position the mount as far forward as you
can. Before fully tightening the clamp screw,
make sure the bottom
of
the mount is parallel
with the bottom
of
the mirror.
Innovative
Design
And
Precision Manufacturing
BlendMount-US
PATENT#
D625,580 S, D656,811 S, D653,980 S
D690,245 S, D690,246 S, D690,247
Sand
other patents pending
PAGE 1 OF 2
Product specificaties
| Merk: | BlendMount |
| Categorie: | Niet gecategoriseerd |
| Model: | BCB-2121 |
Heb je hulp nodig?
Als je hulp nodig hebt met BlendMount BCB-2121 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd BlendMount
6 Januari 2024
6 Januari 2024
6 Januari 2024
6 Januari 2024
5 Januari 2024
5 Januari 2024
5 Januari 2024
5 Januari 2024
5 Januari 2024
5 Januari 2024
Handleiding Niet gecategoriseerd
Nieuwste handleidingen voor Niet gecategoriseerd
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026
6 Augustus 2026