Blaupunkt KPT-R1 Handleiding

Blaupunkt Radio KPT-R1

Lees hieronder de 📖 handleiding in het Nederlandse voor Blaupunkt KPT-R1 (14 pagina's) in de categorie Radio. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/14
MANUAL KPT-R1
EN Wireless Remote Keypad with Proximity Tags (KPT-R1) 2
DE Funk-Bedienteil mit Tag-Reader (KPT- R1) 4
ES Teclado Remoto Inalámbrico con Tags (KPT-R1) 6
FR Clavier déporté sans fil avec lecteur de badges RFID (KPT-R1) 8
IT Tastiera Remota Wireless con Tag di prossimità (KPT-R1) 10
NL Draadloos Keypad met Tag (KPT-R1) 12
2
EN Wireless Remote Keypad with Proximity Tags (KPT-R1)
Parts Description
1. Active LED (Blue/Orange)
2. Status LED (Blue/Red)
3. Fault LED (Orange)
4. Away Arm Key
5. Home Arm Switch
6. Status Key
7. Disarm Key
8. Panic Alarm
Press both 1 and 3 key to trigger Panic alarm
9. Fire Alarm
Press both 4 and 6 key to trigger Fire alarm
10. Emergency Alarm
Press both 7 and 9 key to trigger Emergency alarm
11. Battery Insulator
12. Mounting Knockouts
13. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover opening.
14. RFID TAG
Package Content
1 x Remote Keypad
2 x wall plugs and screws
2 x RFID Tags
1 x 3V lithium batteries (pre-installed)
1. Learning
For learning the Remote Keypad:
1. Put the Control Panel into learning mode.
2. Press both # and * keys to transmit learn code
3. Refer to Control Manual to complete the learning process.
2. Installation
The Remote Keypad has 2 knockouts on the back
where plastic is thinner for wall mounting.
1. Use the two knockouts on the back to mark
position on the wall at chest height. Open the back
cover.
2. Drill holes into the wall using the knockouts as
template.
3. Fix the keypad base onto the wall with the screw
and plugs provided.
4. Replace the keypad cover onto the base.
3. Operation
Standby Mode
The Remote Keypad features a power saving feature. When no key is pressed
for 5 seconds, the Remote Keypad will turn off automatically to conserve
power. When any key is pressed, the Remote Keypad will wake up and turn on
Active LED to indicate it is now under normal operation.
NOTE: This device works with a genuine Rolling
Code encryption. Please only use it with a control
panel with Rolling Code, otherwise won’t be
possible to pair the device.
Keypad Settings
The Remote Keypad features a Test (programming) mode for you to customize
its setting. Before you start using the Remote Keypad, you should first finish
configuration setting.
The Remote Keypad also feature a Keypad PIN code which is used to access the
Test mode, To enter Test Mode, Enter “0000”(Default Keypad PIN code) + “*” key,
the Active Orange LED will light up.
RFID TAG Management
The Keypad can function with the RFID tags included in the package. By
assigning User PIN Code to a Tag, you can use the Tag to Arm/Home/Disarm the
Control Panel with a simple swipe.
Up to 6 tags can be stored in the Keypad and assigned to User PIN Codes for
panel control:
Under Test Mode, the following functions include:
Key Function
* + 1” Tag Management
* + 7” Transmit learn code (same as pressing
both # and * keys under normal mode)
* + 2” Enable dual key Panic Alarm function
* + 3” Enable dual key Fire Alarm function
* + 4” Enable dual key Medical Alarm function
* + 5” Disable all dual key functions
* + 6” Change Keypad PIN Code:
1. Enter old code + “Status Key
2. Enter new 4-digit code + “#” key
* + 8” Enable Arming without Use PIN code
function
* + 9” Enable Arm with User PIN code function
(Default)
* + 0” Enable Arming with KP PIN code function
“Disarm” twice To leave Test Mode
Add New Tag:
1. Enter Keypad Test Mode.
2. Enter “*”+“1” for Tag Management. Red Status LED will light up.
3. Enter a 4-digit “Control Panel User PIN Code + “#” key.
Status RED LED flashes Success
Status Blue LED flashes with 4 beeps Error: Wrong PIN Code length
Status Red LED flashes with 4 beep Error: Keypad already stored 6 Tags
4. Put the TAG close to the Keypad when Status Red LED is flashing.
Status RED LED On with 2 beeps Success
Status Red LED On with 1 bee Same PIN Code already assigned to
this Tag
Status Red LED On with 4 beeps Error: Tag already assigned to ano-
ther User PIN Code
5. After finish adding new Tag, press “Disarm key to exit Tag Management.
Remove Existing Tag:
1. Enter Keypad Test Mode.
2. Enter “*”+“1” for Tag Management. Red Status LED will light up.
3. Enter the User PIN Code of the Tag you want to remove, then press the
Status key.
4. The Keypad will emit a long beep, the Tag info is removed.
Mounting
Knockouts
x 2
3
Away Arm 1. Enter a Control Panel User PIN
Code + Arm” Key.
2. Press Arm” Key + put Tag on
Keypad.
Home Arm 1. Enter a Control Panel User PIN
Code + “Home” Key.
2. Press Home” Key + put Tag on
Keypad.
Disarm 1. Enter a Control Panel User PIN
Code + “Disarm” Key.
2. Press Disarm Key + put Tag on
Keypad.
If Remote Keypad is set to Arm without Use PIN code (“* + “8” under Test Mode)
Away Arm Press Arm” Key
Home Arm Press “Home” Key
Disarm Enter a Control Panel User PIN Code
+ “Disarm” Key
If Remote Keypad is set to Arm with Keypad PIN code” (“*” + “0” under Test Mode)
Away Arm Enter Keypad PIN Code + Arm Key
Home Arm Enter Keypad PIN Code + Home” Key
Disarm Enter Keypad PIN Code + Disarm”
Key
Checking Control Panel Status
Press the Status key to inquire Control Panel status, the Status LED will light up
according to Control Panel mode.
Red LED On Away Arm mode
Red LED Flash Home Arm mode
Blue LED on Disarm mode
Dual Key Alarm Function
Dual Key Alarm function will activate alarm when both keys are pressed at the
same time. To use the functions, please enable them under Test Mode. (Default
are disabled)
“1” + 3” Panic Alarm
“4” + 6” Fire Alarm
“7” + 9” Emergency Alarm
LEDs
Active LED
The Active LED light up whenever any key is pressed.
Status LED
The Status LED light up during operation or when the “Status” key is pressed to
inquire Control Panel status
Red LED On Away Arm mode
Red LED Flash Home Arm mode
Blue LED On Disarm mode
Blue LED Flash No reply from Control Panel
Incorrect PIN code
Request for Home arm when under
Away arm mode
Request for Force Arm
Fault LED
The Fault LED light up whenever faults are detected in the alarm system.
Orange LED On Alarm in memory
Orange LED Off Fault exists in system
Battery
The Remote Keypad uses one 3V lithium battery as its power source. It also
features low battery detection function to notify the Control Panel when battery
voltage is low.
When the Remote Keypad is on low battery, follow the procedure below to
change the batteries.
1. Open the back cover
2. Remove the old batteries
3. Press any key several times to fully discharge.
4. Insert the new batteries observing correct polarity.
5. Replace the back cover.
Factory Reset
If you forget your Keypad PIN code, or the Remote Keypad has any problem,
you can reset the Remote Keypad to factory default.
1. Open the back cover and remove the battery
2. Press and hold 3” key and insert battery
3. The Remote Keypad will sound 3 short beeps
4. Release “3” key, the reset process is now complete
4. Specication
Environmental Condition
-10°C to 40°C, relative humidity 85% non-condensing.
Radio
868 MHz
Arm/Home/Disarm
If Remote Keypad is set to Arm with Use PIN code” (“*” + “9” under Test Mode)
Off Keypad in Standby Mode
Blue LED On Keypad in Normal Operation
Blue LED Flash Keypad in Normal Operation and
under Low Battery
Orange LED On Keypad in Test Mode
Orange LED Flash Keypad in Test Mode and under Low
Battery


Product specificaties

Merk: Blaupunkt
Categorie: Radio
Model: KPT-R1
Kleur van het product: Black, White
Connectiviteitstechnologie: Draadloos
Aantal: 1
Compatibiliteit: SA2900 & Q

Heb je hulp nodig?

Als je hulp nodig hebt met Blaupunkt KPT-R1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Radio Blaupunkt

Handleiding Radio

Nieuwste handleidingen voor Radio