Blaupunkt BPS-E650C Handleiding

Blaupunkt Speaker BPS-E650C

Lees hieronder de 📖 handleiding in het Nederlandse voor Blaupunkt BPS-E650C (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Model: BPS-E650C BPS-X65P
Speaker Design 6.5" component 6.5" component
Woofer [in, mm] 6.5in 165mm 6.5in 165mm
Woofer Material PP Carbon Fiber
Woofer Surround Material Rubber Rubber
Tweeter [in, mm] 2.4in 61mm 2.4in 61mm
Dome Material Silk Silk
Peak Power 60W 70W
Recommended Amplier Power [Watts RMS] 30W 35W
Effective Frequency Range [Hz] 55~20000Hz 50~20000Hz
Woofer Mounting Hole Diameter [in, mm] 5.59in 142mm 5.59in 142mm
Top Mount Depth [in, mm] 1.10in 28mm 1.26in 32mm
Bottom Mount Depth [in, mm] 2.28in 58mm 2.28in 58mm
Flush Mounting Tweeter Hole Diameter 2.09in 53mm 2.09in 53mm
Flush Mounting Tweeter Depth [in,mm] 0.91in 23mm 0.91in 23mm
High Pass [dB] @ Hz 12dB, 4000Hz 12dB, 4000Hz
Low Pass [dB] @ Hz 12dB, 4000Hz 12dB, 4000Hz
High Frequency Output Attenuation [dB] 0, 3&6 0, 3&6
Bolt Through Grills - Yes or No Yes Yes
Zn [Ù] 4.1ohm 4ohm
Re [Ù] 3.2ohm 3.7ohm
Splo [dB] @ 1W, 1M 85.1dB 88.2dB
Component Speakers System
E-Series
BPS-E650C
X-Series
BPS-X65P
BP Americas Corp.
9590 NW 40th St Road
Doral, FL 33178
MOUNTING / MONTAJE:
NOTE: BLAUPUNKT strongly recommends that you operate your system at low volume levels prior
to the complete installation of your BLAUPUNKT speakers.
CAUTION: Make sure that all of the speaker wiring is fully protected from cuts, tears or possible
wear. Any short circuit caused from cuts, tears or wears, could severely damage the source unit
or amplier. Make sure all speaker wires easily reach the speaker terminals with no stress on the
wires or connectors.
IMPORTANT: Never cut any metal that is an integral part of the vehicle’s safety or structural
support system. If you are unsure of the importance of any components of your vehicle, it is
recommended that you have your speaker professionally installed.
CHOOSING A LOCATION: It is always best to plan the complete installation prior to attempting to
install any product. The routing of wires, power connections, and mounting location, should be
planned rst. As with any car stereo installation, all work performance should be checked
throughly and carefully prior to the operation of the system.
BLAUPUNKT Speakers are designed to t in almost any factory location. If at all possible, it is
recommended that you use factory locations. This applies mostly to later model cars.
For those earlier model cars, that do not have factory location or are limited to just front speakers,
it is recommended that you choose a location with a sufficient amount of air space.
If there’s not enough air space, the woofer of the speaker may not reproduce low frequencies very
well. It is recommended to mount the speakers in the door panels, kick panels, rear deck, etc.
Ideally, the speakers should be mounted where it will be in an enclosed airspace.
This allows for an extended bass response.
NOTA: BLAUPUNKT recomienda enfáticamente que opere su sistema a niveles de volumen bajos
antes de la instalación completa de tus altavoces BLAUPUNKT.
PRECAUCIÓN: Asegúrese de que todo el cableado de los altavoces esté totalmente protegido
contra cortes, rasgaduras o exposición. Cualquier cortocircuito causado por cortes, rasgaduras o
desgaste podría dañar gravemente la unidad fuente o amplicador. Asegúrese de que todos los
cables de los altavoces lleguen fácilmente a los terminales de los altavoces sin tensión en los
cables o conectores.
IMPORTANTE: Nunca corte ningún metal que sea parte integral de la estructura o del sistema de
seguridad de su vehículo. Si no está seguro de la importancia de algún componente de su
vehículo, s recomendable que haga instalar su altavoz por un profesional.
ELEGIR UNA UBICACIÓN: Siempre es mejor planicar la instalación completa antes de intentar
instalar cualquier producto. La ruta de los cables, las conexiones eléctricas y la ubicación del
montaje deben ser planeado primero. Al igual que con cualquier instalación de estéreo de
automóvil, se debe vericar todo el rendimiento del trabajo completa y cuidadosamente antes de
operar el sistema.
Los altavoces BLAUPUNKT están diseñados para adaptarse a casi cualquier ubicación de fábrica.
Si es posible, es recomensable que utilice ubicaciones de fábrica. Esto se aplica principalmente a
los autos mas recientes. Para aquellos modelos de automóviles anteriores, que no tienen ubicación
de fábrica o están limitados solo al altavoz delantero, se recomienda que elija una ubicación con
suciente espacio de aire.
Si no hay suciente espacio de aire, es posible que el woofer del altavoz no reproduzca muy bien
las frecuencias bajas. Se recomienda montar los parlantes en los paneles de las puertas, los
paneles inferiores, la plataforma trasera, etc. Idealmente, los altavoces deben montarse donde
estarán en un espacio de aire connado. Esto permite una respuesta de graves extendida.
WIRING / CABLEADO:
One component set per channel
At least two amplier channels are needed for stereo operation
Total Impedance: 4 ohms
Un sistema de componentes por canal
Al menos dos canales de amplicación son necesarios para
el funcionamiento en estereo
lmpedancia Total: 4 ohms
0dB 3dB 6dB
Attenuation switch for the tweeter volume
(0dB, 3dB and 6dB)
Conmutador de volumen para el tweeter
(0dB, 3dB y 6dB)


Product specificaties

Merk: Blaupunkt
Categorie: Speaker
Model: BPS-E650C

Heb je hulp nodig?

Als je hulp nodig hebt met Blaupunkt BPS-E650C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Blaupunkt

Handleiding Speaker

Nieuwste handleidingen voor Speaker