BioBrite SunRise Handleiding
BioBrite
Lichttherapie
SunRise
Lees hieronder de đź“– handleiding in het Nederlandse voor BioBrite SunRise (7 pagina's) in de categorie Lichttherapie. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/7
SunRise AlarmTM Clock
(Programmable Model)
INSTRUCTION MANUAL
The SunRise Alarm Clock is a great way to wake up feeling more
refreshed and ready to go. Humans are naturally adapted to wake to the
rising sun and sleep when the sun goes down. Waking up to the SunRise
Clock’s simulated dawn can give your body a gentle and natural boost in the
morning. Please take a few moments to read the directions to ensure you
get off to a good start with your SunRise Alarm Clock.
Setting up the Sunrise Alarm Clock:
For best results, set the clock near your bed on a nightstand or bedside
table close to pillow level. Plug the clock into a wall outlet. Do not use a
power strip, surge protector, or long extension cord. NOTE: Until the time
has been set, or after a prolonged power cut, the clock display will flash on
and off to let you know the time needs to be set.
Before doing anything, you should familiarize yourself with the control
buttons and the clock display. The words below the time
display will show you what setting you are changing and what the current
setting is. To adjust any setting, first make sure the ALARM button
(marked “A”) is pressed IN (off) so the Alarm Set sun symbol is not lit.
Press the PROGRAM button a number of times then, within the next few
seconds, change the setting by pressing the + or – button. (NOTE: after
about 12 seconds, unless the + or – or PROGRAM button is pressed, the
clock will revert to its normal state). Once you have completed a setting
you can press the PROGRAM button again to adjust another setting. Once
you are finished with the program settings, leave the clock alone for 12
seconds, and it will return to displaying the current time.
NOTE if the display is too dim to see, press the ALARM button IN and the
display will become bright. This feature is explained in detail later in the
instructions.
Setting the Time:
Make sure the ALARM (“A”) button is pressed IN (off). Press the
PROGRAM button twice so the display reads “TIME”. Then within the next
few seconds use + and – buttons to adjust the time. The time moves
rapidly if the + or – button is held in.
Changing to a 24-Hour Display:
The clock defaults to a 12- -hour display. To change to a 24 hour display,
make sure the ALARM button is IN so the sun symbol is not lit, then press
the PROGRAM button 3 times. Then within the next few seconds press the
+ or – button. The display will alternate between "24 HOUR” and "12 HOUR".
Once the display has switched to "24 HOUR", release the buttons. To
switch back to a 12-hour display, follow the same procedure. The “PM”
symbol is only present in the 12-hour mode.
WAKE-UP SEQUENCE
Changing the Wake-Up Time:
Make sure the ALARM button is IN so the sun symbol is not lit then press
the PROGRAM button once, so the Display reads "ALARM TIME". Then
within the next few seconds adjust the alarm time with + and – buttons until
desired time is set (Note: default alarm time is 7:00 a.m.). Holding in the +
or – button will cause the time to change rapidly.
Setting the speed of the Wake-Up Sequence:
The SunRise Alarm Clock is preset for a 30 minute wake-up sequence, i.e.
the light will reach full brightness gradually over 30 minutes. If you wish to
change the wake-up sequence length, you can choose between 15, 30, 60,
and 90 minutes. To alter the wake-up sequence length make sure the
ALARM button is IN so the sun symbol is not lit then press the PROGRAM
button 6 times so the Display reads "FADEUP" followed by a number.
Within the next few seconds press the + or – button, and the Display will
alternate between "FADEUP DEMO" (a special quick mode described under
“Additional Features”), "FADEUP 30" (30 minute sunrise - this is the Default),
"FADEUP 60" (60 minutes), "FADEUP 90" (90 minutes), and "FADEUP 15" (15
minutes).
Setting the Alarm On
Push ALARM button so it is OUT (on). The Display will show the Alarm Set
Sun symbol (*) and the wake up time will be displayed for a few seconds.
The light will slowly fade down (if on), or you can turn it out manually by
pressing the – button. The display will normally go dim once the light level
goes low; this is explained in detail in the section Adjusting the brightness
of the Clock Display.
The SunRise Wake-Up Sequence:
The light will begin to illuminate before your set wake-up time. Once the
light has fully illuminated, and the wake-up time has been reached, the
audible alarm will sound. The audible alarm begins with a quiet beep, and
gradually intensifies to full volume over 30 seconds.
Using the “Snooze” feature:
To temporarily “snooze” the alarm, press the minus button while the alarm is
beeping. The beeper will stop sounding and go off again in 9 minutes. If you
would also like the Sunrise to begin again, then continue pressing the minus
button until the light has gone all the way down. Then, over the next 9
minutes, the light will gradually brighten (this occurs at a quicker rate than
originally as it is brightening over a shorter period of time) and finally the
beeper will sound again.
Turning off the Alarm once awoken:
To turn off the alarm, push the ALARM button IN (off). The beeping will stop
and the light will remain illuminated. If the alarm is not turned off manually,
the beeper and light will automatically shut off after a while.
Disabling the Beeper:
The beeper is set “ON” at the factory - shown as the symbol ))). To disable
the audible beeper that sounds at the end of the wake-up sequence, make
sure the ALARM button is pushed IN (off). Press the PROGRAM button 4
times until the display reads "BEEP ON" or "BEEP OFF". Then within the next
few seconds press the + or – button to alternate between the two. When
the unit switches to BEEP ON, the beeper will sound twice and the )))
symbol will show in the Display. When the unit switches to BEEP OFF, the
unit will beep once and the ))) symbol will no longer be displayed.
READING LAMP
Using the Adjustable Reading Light:
Press and hold the + button to turn the lamp up until it reaches the right
level. To reduce the light level, press and hold the – button.
SUNDOWN SEQUENCE
Product specificaties
| Merk: | BioBrite |
| Categorie: | Lichttherapie |
| Model: | SunRise |
Heb je hulp nodig?
Als je hulp nodig hebt met BioBrite SunRise stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lichttherapie BioBrite
6 December 2023
Handleiding Lichttherapie
- Lichttherapie Philips
- Lichttherapie Medion
- Lichttherapie Auriol
- Lichttherapie Beurer
- Lichttherapie Homedics
- Lichttherapie Konig
- Lichttherapie Lanaform
- Lichttherapie Marquant
- Lichttherapie Medisana
- Lichttherapie MT Logic
- Lichttherapie Pure
- Lichttherapie Silvercrest
- Lichttherapie Technoline
- Lichttherapie TFA
- Lichttherapie Oregon Scientific
- Lichttherapie Bush
- Lichttherapie Conair
- Lichttherapie Davita
- Lichttherapie Dayvia
- Lichttherapie Lumie
- Lichttherapie Prologue
- Lichttherapie Iwaku
- Lichttherapie BIOS Medical
- Lichttherapie Liroma
- Lichttherapie DistinQ
- Lichttherapie Panacea
- Lichttherapie Sunrise
Nieuwste handleidingen voor Lichttherapie
20 Februari 2024
20 Februari 2024
4 Januari 2024
6 December 2023
21 November 2023
21 November 2023
20 November 2023
24 Juli 2023
24 Juli 2023
7 Juli 2023