Binatone X-Speaker Handleiding

Bekijk gratis de handleiding van Binatone X-Speaker (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 318 mensen en kreeg gemiddeld 5.0 sterren uit 5 reviews. Heb je een vraag over Binatone X-Speaker of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Unpacking your phone

Corded Telephone

1. Where to find it

2. Installation

1. Locating the Base unit

The Base unit should be placed on a level surface, in a position where:

the telephone line cable will reach your telephone line socket or

extension socket.

it is not close to a sink, bath or shower, or anywhere else where

it is not close to other electrical equipment - fridges, washing

machines, microwave ovens, TVs, fluorescent lights, etc.

2.

4. Plug one end of the telephone line cord into the socket in the back

5.Lift the Handset and check forDial tone in the earpiece.

Always use the

telephone line

cord supplied

with your

Other telephone

line cords may

not work.

2. Installation

it might get wet.

Making a

1Press the SPEAKERPHONE button,

2Dial the telephone number you wish to call.

3To end the call,press the SPEAKERPHONE

call

Toanswer a

call

4. Telephone Operation

Inthebox you will find:

x Base Unit

x Handset

x Coiled Handset cord

x Telephone linecord

for Base unit

x User manual

Keep the packing

materials in a safe

place in case you later

need to transport

Keepyour sales (till)

receipt, whichis your

guarantee.

the unit.

3. Desk/W

2. Installation

3. Wall mount installation

BE CAREFUL to check that there are no wires or pipes hidden in the wall.

Hang the base unit on the screws using the wall mount slots.

You may need to remove the telephone from the wall and tighten the screws so

cradle with the parking hook on the cradlearranged to fit in the parking recess

that the cradle is securely fixed and does not wobble. Place the Handset on the

Press the

button to

SPEAKERPHONE

answer call.

PB10

PB10 phone.

1. Number / photo memory button

2. VOL-(volume-)/STORE button

3. Speakerphone( ) button

- This flashes when the phone is ringing

To Modular

Wall Jack

6. Ringer ON/OFF( )button

Wall mount

To place the PB10 phone on a wall,

on the wall that are mm

centers as .

mark two

apart to lay the fixing

points

shown below

speakerphone

volume

During a call;

Adjust the volume ofthe speakerphone to the

SPEAKERPHONE

volumebutton located atthe

left and right side of the speakerphone button.

Press the SPEAKERPHONE button on the

Base unit.

Ö

The IN USE light indicator will

Toend acall

turn OFF.

To adjust the

4. IN USE/RINGER( )-in Use /ringer light

the phone is on a call.

of the base unit, and plug the other end into a modular wall jack.

under the earpiece on the Handset.

high or lowvolume levelusing the

Fix two screws (7mm head screws required, not supplied)

approximately 7mm

at the marked locations,

between the wall and the screw head.

leaving

VOL-

VOL+

Listen for a dial tone.

button.

93mm

93

If you have aBroadband line

If you connect your telephone to

insert a micro-filter between the

otherwise you may get

interference between the telephone and the broadband,

which could cause problems.

a line with a broadband

connection, you will need to

In a home with broadband, every telephone must have a micro-filter connected,

not just the one at the telephone point that your modem is connected to.

If you need more broadband micro-filters, contact your broadband supplier.

telephone and the telephone line,

TELEPHONE

1

- This is on when

for an incoming call.

5. VOL+(volume+)/PAUSE button

6

23 4

5

Or Visit Our Website:

WWW.binatonetelecom .com

Product specificaties