Bestway Hydro-Force 65046 Handleiding

Bestway Boot Hydro-Force 65046

Lees hieronder de 📖 handleiding in het Nederlandse voor Bestway Hydro-Force 65046 (32 pagina's) in de categorie Boot. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/32

65046

OWNER’S MANUAL

bestwaycorp.com/support

Visit Bestway YouTube channel

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

Fo Q, nu , idr FA Ma als V eos r O

Spare arts P , Please Visit

bestwaycorp.com/support

1 5

12 3

0.24 bar

(3.5 psi)

12 3

0.35 bar

(5 psi)

OWNER’S MANUAL

WARNING

IMPORTANT SAFETY INSTRUCTIONS

Follow all the Safety and Operating Instructions. If you

don’t follow these instructions, it may cause the boat to

overturn or explode and result in drowning.

1. Do not exceed the maximum recommended number of persons. Regardless of the number of

persons on board, the total weight of persons and equipment must never exceed the

maximum recommended load. Always use the seats /seating spaces provided.

2. When loading the craft, never exceed the maximum recommended load: Always load the craft

carefully and distribute loads appropriately

to maintain design trim (approximately level). Avoid placing heavy weights high up.

NOTE: The maximum recommended load includes the weight of all persons onboard, all

provisions and personal effects, any equipment not included in the light craft mass, cargo (if

any) and all consumable liquids (water, fuel, etc.).

3. When using the boat, life saving devices such as life jackets and buoys should be

pre-inspected and used at all times.

4. Before every use, carefully inspect all boat components including air-chambers, grab ropes,

oars, and air valves, to ensure everything is in good condition and tightly secured. If you find

any damage, please stop to repair it.

5. Buckets, water scoops and air pumps should always be available in case of air leakage or if

the boat takes on water.

6. When the boat is in motion, all passengers must remain seated at all times to avoid going

overboard. Keep the boat balanced. Uneven distribution of persons or load in the boat may

cause the boat to overturn and result in drowning.

7. Use the boat near the shore and beware of natural factors such as wind, tide waters and tidal

waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS.

8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate

the other air chamber to prevent the boat from sinking.

9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement,

shells, glass, etc. may puncture the boat. To avoid damage, do not drag the boat on rough

surfaces.

10. When choosing an outboard motor, refer to the technical specifications section of this manual

to determine acceptable horsepower ratings.

11. For electrical motors equipped with batteries, note that battery acid can be caustic, which can

cause damage to both skin and boat materials.

12. For motors which use fuels such as gas, oil or petrol, since fuel is a flammable substance, it

should be kept away from open flames. Further, clean the boat material immediately if fuel

spatters onto the boat surface. Be aware of the potential harmful efects of liquids such as

battery acid, oil or petrol. The liquids may damage your boat.

13. Inflate according the numbered air chamber and rated pressure of the boat, or it will cause

over-inflation and potential and boat explosion. Exceeding the data given on the capacity

plate may cause the craft to be damaged, overturn and lead to drowning.

14. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.

15. Know how to operate a boat. Check in your local area for information and/or training as

needed. Inform yourself about local regulations and dangers related to boating and/or other

water activities.

SAVE THESE INSTRUCTIONS

Registration (For US/Canada customers only)

If you need to register your boat, please have the boat Hull Identification Number and model

name ready and then visit bestwaycorp.com/support to obtain your Certificate of Origin, or you

can send e-mail to service@bestwaycorp.us for the Certificate of Origin.

PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW

OWNER WHEN YOU SELL THE CRAFT.

REPAIR INSTRUCTIONS:

• Fully clean the area to be repaired.

• Cut the correct size from the repair patch

material.

Apply only the amount of glue needed to cover

the repair site.

• Press the repair patch firmly to repair site for

30 seconds.

• Wait for 1 hour before inflation.

Storage

1. Remove the Oars from the oarlocks.

Note: Keep all accessories for future use.

2. Carefully clean the boat using a mild soap with clean water.

Note: Do not use acetone, acid, and/or alkaline solutions.

3. Use a cloth to gently dry all surfaces.

Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric

blowers. Doing so will cause damage and shorten the boat’s life span.

4. To deflate, open the Air Valves pushing the control stem in and rotating until the valves stay

open. Deflate all the hull chambers at the same time so the air-pressure drops together. This

will prevent damage form occurring to the boat’s inner structures.

5. Next deflate the Keel.

6. Disassemble the seat and floor.

7. Fold the boat from front to back to remove additional air. You can also use a pump to drain any

remaining air.

The glue is not included in the repair kit due to

shipping constraints. You can find

silicone-based glue at most retail outlets.

Carefully read the warning labels and closely

follow instructions on the back of glue before

attempting the following repair steps.

Maintenance

1 Inflate according to the PSI marked besides the valve;.

2 To avoid the long-time exposure to sunshine or rain, put the outside cover on top for protection .

when it not being used;

3 Clean it with mild soap water and soft cloth in case it is not going to be used for a long time. .

Dry it before putting them away. Store it at a dry and shady place and keep it out of reach of

Children.

4 Use the spanner to tighten the air valve if it is leaking ..

NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge is just

for reference, should not be used as a precision instrument.

- Only use Bestway® approved inflation pumps.

- Never use motor-driven high-pressure air pumps as this may result in over-inflation.

- Under and over-inflation will result in safety hazards.

- Always check the inflation pressure before using the boat.

- Never stand on or rest objects on the boat during inflation.

- Never open the cap of air valve while the boat is in use.

- Be sure the valve is tightly closed before using the boat.

Note: When the oars are not in use, lock the oars into the Oar Clasps to avoid damage.

Outboard Motor Installation

With the boat fully inflated and in the water, attach your outboard motor onto Engine Mount at the

center of the Transom.

Note:

- Ensure the motor is always fixed on the Transom.

- Read the instruction of outboard motor for correct installation and operation.

- Overpowering a boat can result in serious injury, death or boat damage. The maximum motor

power to be used see marking on the product.

Deflation

WE SUGGEST NOT TO RETURN

THE PRODUCT TO THE STORE

QUESTIONS? PROBLEMS?

MISSING PARTS?

Fo Q, Manu , idr FA als V eos r O

Spare arts ease P , Pl Visit

bestwaycorp.com/support

Note:

- The floorboards must be assembled before inflating the hull.

- Extended exposure to sun can shorten the lifespan of your boat. We suggest not leaving boats in

direct sunlight for more than 1 hour after use.

001

004

005

002

003

006

007

Part No. Description QTY SPARE PART NO.

001 Boat

002

Floor board

003

Bench seat

004 Oar 1

pair

005 Air pump

006 Drain valve

1007 Repair kit

P04760

F3H101ASS17

P03777

P5L334ASS19

P05323

F3C092ASS14

P6J718ASS18

WARNING: To avoid damage to the boat and injury to passengers, please don’t exceed

the data given on the builder’s plate.

Technical Specifications

Item Size Recommended

working pressure Maximum load capacity Maximum motor

power

2.25 kW (3 hp)

7'6" x 51" x 13"

2.30m x 1.30m x 33cm

258 kg (568.8 lbs.)

2 adults

3.5 psi

0.24 bar

65046

Floor board

pressure

5 psi

0.35 bar

Product specificaties

Merk:	Bestway
Categorie:	Boot
Model:	Hydro-Force 65046
Kleur van het product:	Grijs
Gewicht:	23409 g
Breedte:	1300 mm
Gewicht verpakking:	- g
Breedte verpakking:	580 mm
Diepte verpakking:	960 mm
Hoogte verpakking:	310 mm
Soort:	Opblaasbare boot
Type verpakking:	Doos
Maximale gewichtscapaciteit:	258 kg
Materiaal:	PVC
Lengte:	2300 mm
Opbergetui:	Ja
Aanbevolen gebruik:	Reizen/recreatie
Aantal personen:	2 persoon/personen
Producten per pallet:	5 stuk(s)
Verpakkingsvolume:	186000 cm³
Intrastatcode:	89031010
Interleaved Two of Five (ITF-14):	06942138981315
Minimum bestelhoeveelheid:	1 stuk(s)
Aantal kamers:	2
Maximaal motorvermogen:	2250 W
Inclusief reparatiemiddel:	Ja
Aftapkraan:	Ja
Inclusief roeispanen:	Ja
Aantal roeispanen:	2
Lengte roeispaan:	1.45 m
Materiaal roeispaan:	Aluminium
Handluchtpomp:	Ja
Motorbevestiging:	Ja
Sleepkabel:	Ja
Sleephaak:	Ja
Materiaal sleephaak:	Metaal
Lengte sleepkabel:	10 m