Ballymore Cantilever CL-7-35 Handleiding

Ballymore Ladder Cantilever CL-7-35

Lees hieronder de đź“– handleiding in het Nederlandse voor Ballymore Cantilever CL-7-35 (2 pagina's) in de categorie Ladder. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
CONSIDER BEFORE EACH USE
1. Choose the correct ladder or work platform for the speci c task.
If unsure, consult the factory.
2. Metal ladder stands and work platforms conduct electricity. Keep away from
energized electrical circuits. Contact could cause electrocution.
3. Use in accordance with instructions and warnings provided.
4. Common sense and good judgment must be used at all times.
Do not use
• If in poor health
• If subject to fainting.
• If using drugs (including prescribed medication which could affect equilibrium)
or alcohol.
5. Wear appropriate footwear. High heel shoes and shoes with slippery soles
are dangerous.
INSPECT BEFORE EACH USE
1. Inspect thoroughly for missing, damaged or worn components.
2. Inspect for loose fasteners.
3. See that all caster assemblies including lock steps operate freely
(see “MAINTENANCE”).
Remove damaged or malfunctioning (units which do not roll and lock properly or
do not sit square and level) ladders and work platforms from service. Do not make
temporary repairs.
PROPER USE OF MOBILE LADDER STANDS AND MOBILE
WORK PLATFORMS
GENERAL SAFETY
1. Users are cautioned to take proper safety measures when a ladder or work platform
is used in areas where electrical lines exist. Prevent any contact or possible contact
with an energized uninsulated circuit or conductor in order to avoid electric shock,
short circuit and serious injury.
2. Do not use on uneven or sloping surfaces.
3. Do not overload - observed posted capacity.
4. Do not move/roll an occupied ladder or platform. On lockstep ladder, make
sure ladder is in the climbing position (front legs secured rmly to the oor
before climbing).
5. Shifting weight on a ladder equipped with spring-loaded casters alters spring
compression, causing light “ oat” feeling. User should be aware of this characteristic
in order to expect and compensate for it.
6. Handrails (if equipped) should be used when climbing or descending the ladder.
7. On 59Âş slope ladder, always face the ladder when climbing or descending. Step
slope is too steep to face outward. 50Âş slope ladders allow forward facing descent.
8. Keep body centered on ladder or work platform. Avoid shifting weight suddenly
and do not push, pull, lean over, etc. in any way that may cause ladder legs or casters
to lift off oor.
9. Do not over-reach. Keep unit close to the work. If necessary, descend and relocate
the unit to prevent overreaching.
10. Do not place any object on the top step or platform in order to gain additional
height.
11. Do not climb on rails.
12. Do not store materials or equipment on steps.
13. Do not enter or exit any step of the unit to/from another elevated surface unless
the unit has been positively secured against movement.
14. Do not place an occupied ladder or work platform in front of a door unless the
door is secured in an open position, locked, or attended.
15. Mobile ladder stands are designed for use by one (1) person only.
MAINTENANCE
Periodic* inspection and maintenance should include the following:
1. Inspect ladder periodically for wear, damage and corrosion e.g., rust, worn or
broken treads, broken welds, bent parts and frame members, etc.
2. Ch g - un shoul str t and square and ho d s l on the eck ali nment it d be aigh s ul it leve oor.
3. Ladders equipped with spring-loaded casters:
• Remove and inspect all casters and springs.
• Look for excessive or uneven wear on caster stems.
• Be sure wheel is round and rotates freely in fork.
• Check caster sleeve on ladder base making sure
sleeve is straight.
• Check inside of caster sleeve and remove any foreign material.
• Hole in top of caster sleeve should be round. If not,
caster assembly may not operate properly.
• Clean caster stems and springs. Apply a thin coat of oil.
• Replace caster assembly checking to assure smooth operation.
NOTE: Replace any broken, worn or missing casters or springs. In order to provide
the proper replacement parts, advise factory of model number; or if unknown, the
number of steps, width of steps and if ladder has handrails or not. Ladder may not
function properly and may even be dangerous if wrong casters and/or springs are
installed.
IMPORTANT - READ BEFORE USING -
Instructions Should Remain With Ladder
ASSEMBLY, USE, AND MAINTENANCE INSTRUCTIONS FOR
MOBILE LADDER STANDS AND MOBILE WORK PLATFORMS
INSPECT UPON RECEIPT
Carefully inspect ladder upon receipt for shipping damage. Assemble ladder promptly
to assure it has been delivered in good condition. It is your responsibility to notify the
carrier immediately if your shipment has been damaged. Never use a ladder that has
been damaged or does not function properly. Each ladder received a quality control
inspection prior to shipment. Should your ladder function improperly for any reason,
it probably has been subjected to damage in transit. Protect your interests by notifying
the carrier immediately, so that action will be taken to repair or replace your ladder as
soon as possible.
OWNER/EMPLOYER RESPONSIBILITY*
The owner of a ladder, or employer having supervisory control of the unit, has
total responsibility for its proper inspection, set-up, use and maintenance. It is the
employer’s responsibility to instruct his/her employees in the proper use of the
ladder. Employees are required to read and understand the manufacturer’s operating
instructions before being allowed to use this ladder. Be aware of the posted warnings
on the ladder. Should any of the warning labels become illegible or need replacing, the
factory will send new ones upon request.
*Reference American National Standard (A 14.7) for Mobile Ladder Stands and
Mobile Work Platforms..
TO ASSEMBLE
READ ATTACHED INSTRUCTIONS
WARNING
USING INCORRECT NUTS & BOLTS CAN CAUSE SAFETY HAZARD.
Ladders are shipped with lock-type fasteners* which by design can only safely be
used once. If it becomes necessary to disassemble your ladder, be sure to discard used
hardware and purchase new locking fasteners (1/2”), available at hardware stores or
from the factory.
*Double check when assembling ladder to assure that no non-locking nuts have been
inadvertently included.
4. Ladders equipped with lock steps:
and swivels 360 degrees without binding.
5. Some models use other caster and lock arrangements such as wing brake,
combination wheel and swivel locks or floor locks. Be sure these devices work as
intended and are not worn or damaged.
6. Most ladders employ rubber tips on two or four legs. Check for excessive or
uneven wear, replace as necessary.
NOTE: Ladders are unsafe if tips are worn or missing.
If ladder has been in service without tips, legs may be worn to the point where new
tips may not contact floor firmly enough to lock ladder.
7. Some models employ lock-type fasteners. Check to make sure they are present
and tight.
necessary to disassemble your ladder be sure to discard used nuts and bolts and
replace with new locking fasteners.
8. Check to see that warning labels (located on the front of the steps) are affixed and
legible. Contact factory if new labels are required.
9. Ladders and platforms that do not work properly, are damaged, or weakened for
any cause, must be removed from service until repaired.
10. Ladders and platforms which can not be repaired must be destroyed.
11. No modifications should be made to product unless approved by factory.
*At least every 3 months, more frequently if the ladder is used on a daily basis. User
must determine the period between maintenance inspections based on severity of use.
WARNING: THE MATERIALS IN THIS PRODUCT CONTAIN
CHROMIUM COMPOUND ELEMENTS WHICH ARE KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE CANCER AND OR BIRTH
DEFECTS OR OTHER REPRODUCTIVE HARM.
FOR MORE INFORMATION, VISIT www.P65Warnings.ca.gov
B-0304/10M
Ballymore Co., Inc. Manufacturing Facilities
Garlin Enterprises
800-762-8327
ballymore.com
.rD noslraC drannuG 105
Coatesville, PA 19320


Product specificaties

Merk: Ballymore
Categorie: Ladder
Model: Cantilever CL-7-35

Heb je hulp nodig?

Als je hulp nodig hebt met Ballymore Cantilever CL-7-35 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden