Axler CS-CPS-20A Handleiding
Bekijk gratis de handleiding van Axler CS-CPS-20A (6 pagina’s), behorend tot de categorie Statief. Deze gids werd als nuttig beoordeeld door 35 mensen en kreeg gemiddeld 4.5 sterren uit 18 reviews. Heb je een vraag over Axler CS-CPS-20A of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
CS-CPS-20a
QUICK-S TART
GUID E
• Please read and follow these instructions, and keep this
manual in a safe place.
• Keep this product away from children.
• Make sure everything is secure before proceeding.
• Make sure that this product is intact and that there are no
missing parts.
• To avoid damage to this product, be careful not to overtighten
or improperly thread any of the threaded fittings.
• Do not exceed the maximum load capacity.
• Be careful not to catch your fingers in any of the moving parts.
• All images are for illustrative purposes only.
P R E C A U T I O N S
S l i d e r :
1. Camera base
2. Mounting plate locks
3. Top mounting plate
4. Belt
5. Brake
6. Adjustable feet (×4)
7. Tripod mounting sockets *
(1/4″ ″-20 and 3/8 -16)
*under mounting base
8. Mounting base
9. Bubble level
A l s o I n c l u d e d :
• 3/8″-16 bushing
(for camera mount)
• 7/64″ hex key
(for tension screw
adjustment)
• T9 hex key
• Set screws (×2)
• Carry case
• User manual
O V E R V I E W
321
2
4 5
9 66 87
G E T T I N G S T A R T E D
Place the CS-CPS-20a Expanding Caterpillar Slider
on a steady surface. When used on its feet, e.g., on
the ground or a table, the CS-CPS-20a offers 18″
of sliding. You can adjust the length of the feet to
prevent the slider from wobbling and fine-tune the
position of the slider.
To extend the foot, rotate it clockwise. To retract
the foot, rotate it counterclockwise. (Fig. 1)
Tip: Use the onboard bubble level to determine
whether your shot is aligned with the horizon.
M O U N T I N G T H E S L I D E R
You can use a heavy-duty tripod or light stand to
support the slider and gain both height and tracking
length. When mounted, the CS-CPS-20a delivers
30″ of sliding length. The slider’s mounting base is
equipped with 1/4″-20 and 3/8″-16 sockets.
To mount the slider, follow these steps:
1. Center the mounting base on the slider, and lock it
down by tightening the brake. (Fig. 2)
2. Align your tripod’s threaded post with the
corresponding mounting socket in the slider’s
mounting base. Place the slider onto the threaded
post and carefully rotate the tripod until fully
attached. (Fig. 3)
3. Mount your camera to the slider according to the
directions below.
Note: To avoid wobbling and camera shake, use
sand bags or other weights to stabilize your tripod.
Product specificaties
| Merk: | Axler |
| Categorie: | Statief |
| Model: | CS-CPS-20A |
Heb je hulp nodig?
Als je hulp nodig hebt met Axler CS-CPS-20A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Statief Axler
25 Februari 2025
19 December 2024
19 December 2024
19 December 2024
19 December 2024
19 December 2024
19 December 2024
19 December 2024
Handleiding Statief
- Kaiser Fototechnik
- Zhiyun
- Fidlock
- JOBY
- Explore Scientific
- Robus
- Alpine
- Dorr
- MOZA
- Magnus
- Testo
- FLM
- Peak Design
- Elgato
- Asus
Nieuwste handleidingen voor Statief
15 Juni 2025
15 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
6 Juni 2025
24 Mei 2025