AXESS AX-ADXSVI-CH3 Handleiding

Bekijk gratis de handleiding van AXESS AX-ADXSVI-CH3 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 102 mensen en kreeg gemiddeld 4.7 sterren uit 7 reviews. Heb je een vraag over AXESS AX-ADXSVI-CH3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

AX-ADXSVI-CH3AX-ADXSVI-CH3

REV. 8/28/17REV. 8/28/17© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION

Integrate • AxxessInterfaces.comIntegrate • AxxessInterfaces.com

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

Dodge/RAM accessory and NAV output CAN harness 2013-up

• Provides accessory (12 volt 10 amp)

• Retains R.A.P. (retained accessory power)

• Used in non-amplified systems or when replacing amplified system

• Provides NAV outputs (parking brake, reverse, and V.S.S.)

• Prewired ASWC-1 harness included (ASWC-1 sold separately)

• Retains back-up camera (if through the OE radio)

• Retains the use of the 3.5mm AUX jack

• High level speaker input

• USB updatable

Note:

This harness must be used along with the AX-ADXSVI

DODGE

Dart

(small screen option) 2013-2016

RAM

1500, 2500, 3500

(small screen option) 2013-up

Chassis cab 3500, 4500, 5500

(small screen option) 2013-up

APPLICATIONS

WIRING THE AX-ADXSVI-CH3

• Connect the Yellow wire to the radio’s 12 volt battery or memory wire.

• Connect the wire to the radio’s ground wire.Black

• Connect the wire to the ignition wire of the aftermarket radio.Red

• Connect the wire to the illumination wire of the aftermarket radio. If the Orange

aftermarket radio has no illumination wire, tape off the wire.Orange

•

Connect the wire to the left front positive speaker output of the aftermarket radioWhite

.

• Connect the wire to the left front negative speaker output of the aftermarket radio.White/Black

• Tape off and disregard the following (1) wire, will not be used in this application:

Blue/White labeled "500L amp turn on"

• Connect the wire to the right front positive speaker output of the aftermarket radio.Gray

•

Connect the Gray/Black wire to the right front negative speaker output of the aftermarket radio

.

• Connect the wire to the radio’s left rear positive speaker output.Green

• Connect the wire to the radio’s left rear negative speaker output.Green/Black

• Connect the wire to the radio’s right rear positive speaker output.Purple

• Connect the wire to the radio’s right rear negative speaker output.Purple/Black

The following wires are for the aftermarket radios that have navigation built in.

• Connect the wire to the parking brake wire of the aftermarket navigation radio (if applicable).Light Green

•

Connect the wire to the VSS or speed sense wire of the aftermarket navigation radio (if applicable).Blue/Pink

• Connect the wire to the reverse wire of the aftermarket navigation radio (if applicable).Green/Purple

• Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to test the radio.

•

Tape off and disregard the following (1) wire, will not be used in this application:

Blue/White

labeled "500L amp turn on".

RCA CONNECTIONS

•

Connect the Yellow RCA to the "video in" of the aftermarket radio to retain the OE back up camera (if equipped).

• Connect the and RCA to the audio "AUX in" of the aftermarket radio to retain the OE 3.5mm jack WhiteRed

(if equipped).

ASWC-1 (IF INSTALLING)

After the XSVI is initialized, plug in the ASWC-1 into the 12-pin harness of the AX-ADXSVI-CH3

and refer to the

ASWC-1 instructions.

KPNOWLEDGE IS OWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and spected re

mobile electnics school in our industry.ro

Log onto www.installerinstitute.com or call

800-354-6782 for mo information and take steps re

toward a better tomorrow.

®

Metra recommends MECP

certified technicians

CAUTION!

All accessories, switches, climate controls

panels, and especially air bag indicator lights must

be connected before cycling the ignition. Also, do

not remove the factory radio with the key in the on

position, or while the vehicle is running.

Product specificaties