AXESS AX-ADDCAM-CH6 Handleiding

Bekijk gratis de handleiding van AXESS AX-ADDCAM-CH6 (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 26 mensen en kreeg gemiddeld 4.4 sterren uit 5 reviews. Heb je een vraag over AXESS AX-ADDCAM-CH6 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

AX-ADDCAM-CH6AX-ADDCAM-CH6AX-ADDCAM-CH6

INSTALLATION INSTRUCTIONSINSTALLATIONINSTRUCTIONSINSTALLATIONINSTRUCTIONS

REV. 7/11/18REV. 7/11/18REV. 7/11/18© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION

Integrate • AxxessInterfaces.comIntegrate • AxxessInterfaces.comIntegrate • AxxessInterfaces.com

 • Control 1 - Gray/Blue wire

 • Control 2 - Gray/Red wire

 • Control 3 - Orange wire

 • Control 4 - Orange/White wire

 • Control 1 - Gray/Blue wire

 • Control 2 - Gray/Red wire

 • Control 3 - Orange wire

 • Control 4 - Orange/White wire

 • Control 1 - Gray/Blue wire

 • Control 2 - Gray/Red wire

 • Control 3 - Orange wire

 • Control 4 - Orange/White wire

Fiat Family2015-up*

INTERFACE FEATURES

• “Plug & Play” harness for the AX-ADDCAM interface (sold separately)

• 

Reverse signal trigger generated via CAN bus communication of the vehicle

• 

Turn signal trigger generated via CAN bus communication of the vehicle

• (4) Programmable camera control wires (configured through the 

Axxess Updater program)

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink

• Tape • Wire cutter • Zip ties

CONNECTIONS

• For vehicles

with

a factory camera: The camera signal will need to be 

interrupted and connected to the corresponding input/output RCA jacks 

on the AX-ADDCAM interface.

• 

Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera 

output”, to the RCA jack on the AX-ADDCAM interface labeled “Camera 1”.

• 

Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera input”, 

to the RCA jack on the AX-ADDCAM interface labeled “Camera output”.

• For vehicles

without

a factory camera: 

• Connect the RCA jack on the AX-ADDCAM-CH6 labeled “Camera input”, to 

the RCA jack on the AX-ADDCAM interface labeled “Camera output”.

• Disregard the RCA jack labeled “Camera output”, it will not be used in 

this application. 

• 

Disregard the following (2) wires, they will not be used in this application:

 

Blue/Green

 labeled “VSS input”, 

Green/Red

 labeled “VSS output”

ANALOG CONTROL TRIGGER WIRES

• The optional analog control wires can be activated with either a negative 

or positive trigger depending on how they are configured in the Axxess 

Updater program. These wires will only be used if manual control of the 

cameras will be desired. Otherwise tape off and disregard these wires.

Fiat Family2015-up*

INTERFACE FEATURES

• “Plug & Play” harness for the AX-ADDCAM interface (sold separately)

• 

Reverse signal trigger generated via CAN bus communication of the vehicle

• 

Turn signal trigger generated via CAN bus communication of the vehicle

• (4) Programmable camera control wires (configured through the 

Axxess Updater program)

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink

• Tape • Wire cutter • Zip ties

CONNECTIONS

• For vehicles

with

a factory camera: The camera signal will need to be 

interrupted and connected to the corresponding input/output RCA jacks 

on the AX-ADDCAM interface.

• 

Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera 

output”, to the RCA jack on the AX-ADDCAM interface labeled “Camera 1”.

• 

Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera input”, 

to the RCA jack on the AX-ADDCAM interface labeled “Camera output”.

• For vehicles

without

a factory camera: 

• Connect the RCA jack on the AX-ADDCAM-CH6 labeled “Camera input”, to 

the RCA jack on the AX-ADDCAM interface labeled “Camera output”.

• Disregard the RCA jack labeled “Camera output”, it will not be used in 

this application. 

• 

Disregard the following (2) wires, they will not be used in this application:

 

Blue/Green

 labeled “VSS input”, 

Green/Red

 labeled “VSS output”

ANALOG CONTROL TRIGGER WIRES

• The optional analog control wires can be activated with either a negative 

or positive trigger depending on how they are configured in the Axxess 

Updater program. These wires will only be used if manual control of the 

cameras will be desired. Otherwise tape off and disregard these wires.

Fiat Family2015-up*

INTERFACE FEATURES

• “Plug & Play” harness for the AX-ADDCAM interface (sold separately)

• 

Reverse signal trigger generated via CAN bus communication of the vehicle

• 

Turn signal trigger generated via CAN bus communication of the vehicle

• (4) Programmable camera control wires (configured through the 

Axxess Updater program)

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink

• Tape • Wire cutter • Zip ties

CONNECTIONS

• For vehicles

with

a factory camera: The camera signal will need to be 

interrupted and connected to the corresponding input/output RCA jacks 

on the AX-ADDCAM interface.

• 

Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera 

output”, to the RCA jack on the AX-ADDCAM interface labeled “Camera 1”.

• 

Connect the RCA jack from the AX-ADDCAM-CH6 labeled “Camera input”, 

to the RCA jack on the AX-ADDCAM interface labeled “Camera output”.

• For vehicles

without

a factory camera: 

• Connect the RCA jack on the AX-ADDCAM-CH6 labeled “Camera input”, to 

the RCA jack on the AX-ADDCAM interface labeled “Camera output”.

• Disregard the RCA jack labeled “Camera output”, it will not be used in 

this application. 

• 

Disregard the following (2) wires, they will not be used in this application:

 

Blue/Green

 labeled “VSS input”, 

Green/Red

 labeled “VSS output”

ANALOG CONTROL TRIGGER WIRES

• The optional analog control wires can be activated with either a negative 

or positive trigger depending on how they are configured in the Axxess 

Updater program. These wires will only be used if manual control of the 

cameras will be desired. Otherwise tape off and disregard these wires.

*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.*Visit AxxessInterfaces.com for up-to-date vehicle specific applications.

INSTALLATION

• Configure the AX-ADDCAM interface following the installation instructions 

included with the AX-ADDCAM interface. Failure to configure the interface 

will result in the interface not functioning properly.

• Remove the main harness from the factory radio, then install the 

AX-ADDCAM-CH6 in between.

INSTALLATION

• Configure the AX-ADDCAM interface following the installation instructions 

included with the AX-ADDCAM interface. Failure to configure the interface 

will result in the interface not functioning properly.

• Remove the main harness from the factory radio, then install the 

AX-ADDCAM-CH6 in between.

INSTALLATION

• Configure the AX-ADDCAM interface following the installation instructions 

included with the AX-ADDCAM interface. Failure to configure the interface 

will result in the interface not functioning properly.

• Remove the main harness from the factory radio, then install the 

AX-ADDCAM-CH6 in between.

Product specificaties