Audio-Technica AT898 Handleiding

Audio-Technica Microfoon AT898

Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica AT898 (2 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Features

• Maximum intelligibility and clean, accurate reproduction for vocalists,

lecturers, stage and television talent, and houses of worship

• Low-proﬁle design (a mere 5 mm in diameter) is ideal for applications

requiring minimum visibility

• Oers the convenience of battery or phantom power operation

• Rugged design and construction for reliable performance

• Switchable 80 Hz high-pass ﬁlter minimizes pickup of undesired low-

frequency sounds

• Selected models oered in black and beige (-TH)

• Also available in wireless models (without power module) terminated for

use with Audio-Technica wireless systems and many other manufacturers’

wireless systems

Wired Description

The AT899 is a subminiature clip-on/lavalier condenser microphone with an

omnidirectional polar pattern. It is designed to provide accurate reproduction for

vocalists, lecturers, stage and television talent, and houses of worship.

The microphone is intended to be worn on the clothing or hidden in props for excellent

yet unobtrusive sound pickup. The wide-range capability of the microphone ensures

clean, accurate reproduction with high intelligibility for speakers, presenters and other

performers. Its small size makes it ideal for use in applications where minimum visibility

is required.

The microphone requires 11V to 52V phantom power or a 1.5V AA battery for

operation. A battery need not be in place for phantom power operation.

The microphone includes a permanently attached 3 m (9.8') long, 2.0 mm (0.87")

diameter, 2-conductor shielded cable. Its free end connects to the provided AT8537

power module via a TA3F-type connector. The output of the power module is a 3-pin

XLRM-type connector.

A recessed switch in the power module permits choice of ﬂat response or low-

frequency roll-o (via integral 80 Hz high-pass ﬁlter) to help control undesired

ambient noise.

The microphone comes equipped with a power module, a cable clip, a clothing clip

base, a viper clip base, magnet clip base and plate with lanyard, three single mic

holders, two double mic holders, two windscreens, two element covers and a battery.

A protective carrying case is also included. All AT899 models are available with a low-

reﬂectance black ﬁnish; selected models are available in beige.

Operation and Maintenance

The AT899 requires 11V to 52V phantom power or a 1.5V AA battery for operation. A

battery need not be in place for phantom power operation.

To install the battery, unscrew the base of the power supply unit and insert one AA

battery into the battery compartment, being certain to observe battery polarity as

marked. Then simply screw the base shut. Alkaline batteries are recommended for

longest life. Remove the battery during long-term storage.

Output is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3;

Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive acoustic pressure

produces positive voltage at Pin 2.

An integral 80 Hz high-pass ﬁlter provides easy switching from a ﬂat frequency

response to a low-end roll-o. The roll-o position reduces the microphone’s sensitivity

to popping in close vocal use. It also reduces the pickup of low-frequency ambient

noise (such as trac, air-handling systems, etc.), room reverberation and mechanically

coupled vibrations. To engage the high-pass ﬁlter, use the end tip of a paperclip or other

small pointed instrument to slide the switch toward the “bent” line.

For use as a lavalier, attach the microphone about six inches below the chin. Anticipate

movements that may cause the microphone to rub against or be covered by clothing,

and position the microphone to avoid it.

The included single and double mic holders are interchangeable with the included

bases. To change the holders, simply remove original holder and snap in the desired

one. When using the microphone in extremely close situations, slip the included

open-pore foam windscreen over the mic to reduce wind noise or popping. Use the

included element cover to protect the microphone element from contaminants.

CAUTION! To avoid possible injury, use caution when axing the microphone viper

clip to clothing. The pins are sharp and may puncture skin. For best results, ensure

that pin ends rest on outside of clothing.

Avoid leaving the microphone in the open sun or in areas where temperatures exceed

110° F (43° C) for extended periods. Extremely high humidity should also be avoided.

Wireless Models Description

The microphone is also available in a variety of terminations for use with Audio-

Technica and many other manufacturers’ wireless systems. No power module or

battery is included (or required) with the wireless models. The wireless models’

dimensions, polar pattern and included accessories are otherwise identical to those

of the AT899.

The AT899cW is also available unterminated as the AT899c.

Cable Terminations

AT899cH, AT899cH-TH Terminated with a screw-down 4-pin connector

for use with Audio-Technica® cH-style

body-pack transmitters

AT899cW, AT899cW-TH Terminated with a locking 4-pin connector

for use with Audio-Technica® cW-style

body-pack transmitters

AT899cL4, AT899cL4-TH Terminated for Sennheiser® wireless systems

using Lemo connector

AT899cT4 Terminated for Shure® wireless systems using

TA4F-type connector

AT899cT5, AT899cT5-TH Terminated for Lectrosonics® wireless systems

using TA5F-type connector

AT899c, AT899c-TH Unterminated

Model numbers ending in “TH” are beige.

Audio-Technica® is a registered trademark of Audio-Technica. Other product and company names

mentioned herein may be trademarks and/or service marks of their respective owners.

Broadcast & Production Microphones

AT899 Subminiature Omnidirectional Condenser

Lavalier Microphone

Speciﬁcations*

Fixed-charge back plate, permanently

polarized condenser

Omnidirectional

20-20,000 Hz

80 Hz, 12 dB/octave (power module)

Phantom: –43 dB (7.0 mV) re 1V at 1 Pa

Battery: –46 dB (5.0 mV) re 1V at 1 Pa

Phantom: 200 ohms

Battery: 250 ohms

Phantom: 138 dB SPL, 1 kHz at 1% T.H.D.

Battery: 116 dB SPL, 1 kHz at 1% T.H.D.

Phantom: 108 dB, 1 kHz at Max SPL

Battery: 86 dB, 1 kHz at Max SPL

64 dB, 1 kHz at 1 Pa

11-52V DC, 2 mA typical

2.5-11V DC (0.1 mA current consumption

typical at 5V DC)

1.5V AA/UM3

0.4 mA / 1200 hours typical (alkaline)

Flat, roll-o (power module)

Microphone: 0.5 g (0.02 oz)

Power module: 102 g (3.6 oz)

Microphone: 16.0 mm (0.63") long,

5.0 mm (0.20") diameter

Power module: 145.0 mm (5.71") long,

21.0 mm (0.83") diameter

Power module: Integral 3-pin XLRM-type

3.0 m (9.8') long (wired)

1.4 m (55") long (wireless)

M29

AT8537 power module; AT8439 cable

clip; clothing clip base; viper clip base;

magnet clip base and plate with lanyard;

three single mic holders; two double mic

holders; two element covers; two wind-

screens; battery; protective carrying case

Element

Polar pattern

Frequency response

Low frequency roll-o

Open circuit sensitivity

Impedance

Maximum input sound level

Dynamic range (typical)

Signal-to-noise ratio1

Phantom power requirements

Element power requirements

Battery type

Battery current / life

Switch

Weight

Dimensions

Output connector

Cable

Audio-Technica case style

Accessories furnished

In the interest of standards development, A.T.U.S.

oers full details on its test methods to other industry

professionals on request.

1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL

*Measured using AT8537 power module

1 Typical, A-weighted, using Audio Precision System One.

Speciﬁcations are subject to change without notice.

Architect’s and Engineer’s Speciﬁcations

The microphone shall be a ﬁxed-charge condenser. It shall have an omnidirectional

polar pattern and a frequency response of 20 Hz to 20,000 Hz. The microphone shall

operate from an external 11V to 52V DC phantom power source or, alternatively, from

a 1.5V AA/UM3 battery. It shall be capable of handling sound input levels up to 138

dB (phantom) or 116 dB (battery) with a dynamic range of 108 dB (phantom) or 86

dB (battery). Nominal open-circuit output voltage shall be 7.0 mV (phantom) or 5.0

mV (battery) at 1 V, 1 Pascal. Output shall be low impedance balanced (200 ohms –

phantom, 250 ohms – battery).

The microphone shall have a 3.0 m (9.8') permanently attached miniature cable

terminating in a TA3F-type output connector. The output connector shall connect to

a TB3M-type jack on the included power module. The power module shall contain a

recessed switch to permit choice of ﬂat response or 80 Hz low-frequency roll-o. The

output of the power module shall be a 3-pin XLRM-type connector.

The microphone shall be 16.0 mm (0.63") long and have a diameter of 5.0 mm (0.20").

Weight shall be 0.5 grams (0.02 oz). The microphone shall include a power module,

a cable clip, a clothing clip base, a viper clip base, a magnet clip base and plate

with lanyard, three single mic holders, two double mic holders, two windscreens,

two element covers, a battery and a protective carrying case. Finish shall be low-

reﬂectance black.

The microphone shall also be available with a 1.4 m (55") permanently attached

miniature cable terminated for use with Audio-Technica body-pack transmitters and

a variety of other manufacturers’ wireless systems. The wireless models’ dimensions,

polar pattern and included accessories (excluding power module and battery) shall be

identical to those of the wired model. Finish shall be low-reﬂectance black (selected

models available in beige). The microphone shall also be available unterminated.

The Audio-Technica AT899 is speciﬁed.

The Audio-Technica AT899cW [AT899cW-TH]; AT899cH [AT899cH-TH]; AT899cL4

[AT899cL4-TH]; AT899cT4; AT899cT5 [AT899cT5-TH] (wireless version) is speciﬁed.

The Audio-Technica [AT899c]; [AT899c-TH] (unterminated) is speciﬁed.

Function Wire Color

Pin 1 Ground/Shield Copper Color

Pin 2 Bias + In Red

Pin 3 Mic Audio iteWh

Pin 4 umper to Pin 1Source Load J

Pin 5 Line In pen O

AT899cT5, cT5-TH

Function Wir re Colo

Pin 1 Ground/Shield Copper Color

Pin 2 Instrument Jumper to Pin 1

Pin 3 Mic Audio White

Pin 4 Bias + In Red

AT899cW, cW-TH

Function Wir re Colo

Pin 1 Ground/Shield Copper Color

Pin 2 Instrument Jumper to Pin 1

Pin 3 Mic Audio White

Pin 4 Bias + In Red

AT899cH, cH H-T

Function Wire Color

Pin 1 Ground/Shield Copper Color

Pin 2 Bias + In Red

Pin 3 Mic Audio iteWh

Pin 4 umper to Pin 3Source Load J

AT899cT4

Function Wire Color

Pin 1 N/C pen O

Pin 2 N/C pen O

Pin 3 Bias + In, White

Mic Audio

Shell/Case Ground/Shield Copper Color

AT899cL4, cL4-TH

Wireless Termination Diagrams

polar pattern

12" or more on axisLEGEND

Frequency in Hertz

Response in dB

10 dB

100

50 200 10k

500 2k 20k

Roll-off

LEGEND

200 Hz

1 kHz

5 kHz

8 kHzSCALE IS 5 DECIBELS PER DIVISION

240˚

180˚

210˚

270˚

300˚

330˚ 0˚

150˚

120˚

90˚

30˚

60˚

frequency response: 20 –20,000 Hz

AT899

Audio-Technica Corporation

www.audio-technica.com

Product specificaties

Merk:	Audio-Technica
Categorie:	Microfoon
Model:	AT898
Kleur van het product:	Zwart
Snoerlengte:	3 m
Connectiviteitstechnologie:	Bedraad
Levensduur accu/batterij:	1200 uur
Accu gestuurd:	Ja
Stroomverbruik:	0.4 mA
Signaal/ruis-verhouding:	63 dB
Microphone direction type:	Cardioïde
Microfoonhouder:	Ja
Frequentie microfoon:	200 - 15000 Hz
Microphone input impedance:	200 Ohm
Type batterij:	AA
Beschermetui:	Ja
Microphone Total Harmonic Distortion (THD):	1 procent