Audac SP202 Handleiding

Audac Speaker SP202

Lees hieronder de 📖 handleiding in het Nederlandse voor Audac SP202 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

PROFESSIONAL AUDIO EQUIPMENT

Bidirectional Sound Projector SP202

Installation Guide

Sound Projector

SP202

AUDAC

Introduction

The AUDAC SP202 is a Bidirectional and humidity proof sound projector with a high efficiency. It is

suitable for speech and music and ensures a powerful and high quality sound reproduction.

It features two 5” full range speakers and a built-in 100 Volt line transformer with four different power

taps, to be used in large 100V PA applications.

The enclosure is made of solid aluminum with a special weatherproof coating, and the mounting of the

speaker should be done by means of the aluminum mounting bracket. A 1.5m cable is provided for

connecting the loudspeaker.

Installation procedure

1) Before mounting the loudspeaker, make sure that the speaker can be mounted on a safe location and

can be easily aimed to the desired location. Also make sure that the mounting location (Wall / Ceiling)

is solid enough to support the weight of the loudspeaker.

2) The two bolts whereby the loudspeaker is attached to the U-

shaped mounting bracket are meant to focus the speaker into

the desired direction. You can loosen those bolts a bit for

focusing the speaker, and when it’s in the right position,

tighten the bolts again.

Notice that those bolts are locked inside the

loudspeakers body, and can’t be fully removed out of it.

3) The speaker should be mounted using the included U-shaped

mounting bracket. Depending on the mounting surface, the

appropriate fasteners should be used. (wood, concrete, steel, …).

The most simple method for mounting the loudspeaker is by

means of using hexagon bolts, and tightening them by

means of a ratchet wrench.

4) After the loudspeaker is mounted on the desired location, the connection cable can be cut on the

desired length and the connections can be made.

6 mm

29 mm29 mm

Connections

To avoid electric shocks during installation, always switch of the amplifier power when connecting

loudspeakers.

A 4 core connection cable comes out of the cable gland, on top of the loudspeaker. By connecting the

appropriate cable cores, the desires power taps for the loudspeaker can be selected, to be used in 100V

public address applications.

Connections for 100 Volt use:

COM Blue

20 Watt Red

10 Watt Yellow

2.5 Watt Green

Always connect the – pole of the amplifier output to the COM (Blue core). The + pole of the amplifier

can be connected according to the table above for the desired output power.

When the loudspeaker is connected to 70.7V facilities, the power indicated in the table above will be

reduced to half the power, and when connected to 50V facilities, the power will be reduced to a quarter.

When the desired power tap is selected and connected, the loudspeaker is ready to be used.

Product specificaties

Merk:	Audac
Categorie:	Speaker
Model:	SP202
Kleur van het product:	Wit
Gewicht:	2400 g
Breedte:	138 mm
Diepte:	190 mm
Hoogte:	138 mm
Gebruikershandleiding:	Ja
Materiaal behuizing:	Aluminium
Type verpakking:	Doos
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	20 W
Aanbevolen gebruik:	Universeel
Audio-uitgangskanalen:	2.0 kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Aantal drivers:	2
Woofer:	Nee
Diameter driver:	133.35 mm
Frequentiebereik:	150 - 14000 Hz
Gevoeligheid:	91 dB
Luidspreker soort:	2-weg
Montagebeugels meegeleverd:	Ja
Transformatortrappen:	5, 10 W
Ingebouwde bijpassende transformator:	Ja