ATen VW1608 Handleiding

Bekijk gratis de handleiding van ATen VW1608 (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.1 sterren uit 5 reviews. Heb je een vraag over ATen VW1608 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1342

8

9

7

5

6

9

8

20

19

181715161413

12

1110

VW1608 16 × 8 4K Modular Video Wall Processor

www.aten.com

B

Installation

A

Hardware Overview

Package Contents

1 VW1608 16 × 8 Modular Video

Wall Processor

1 power cord

1 power module

1 cable strap

1 user instructions

Support and Documentation Notice

All information, documentation, firmware,

software utilities, and specifications

contained in this package are subject to

change without prior notification by the

manufacturer.

To reduce the environmental impact of

our products, ATEN documentation and

software can be found online at

http://www.aten.com/download/

Technical Support

www.aten.com/support

Scan for more information

Product Page

Power Module Setup

User Manual

The terms HDMI, HDMI High-Definition Multimedia

Interface, HDMI trade dress and the HDMI Logos

are trademarks or registered trademarks of HDMI

Licensing Administrator, Inc.

A

Hardware Overview

1

LCD display

2

alarm LED

3

redundant power LED

4

primary power LED

5

function pushbuttons

6

recessed handle

7

fan module

8

video input board slots*

9

video output board slots

10

redundant power slot

Note:

The top row of input board slots are reserved for potential function

board expansion.

B

Installation

Note:

1. Install the power module onto the unit in advance. Scan the QR code to

access the power module installation guide.

2. Make sure all the equipment you are connecting to the unit is turned off

and disconnected from the power source.

1

Use a grounding wire to ground the unit by connecting one end of the

wire to the grounding terminal, and the other end to a suitable grounded

object.

Note:

Do not omit this step. Proper grounding helps prevent damage to

the unit from power surges or static electricity.

2

Optionally install the video input boards/video output boards to the

VW1608 for expansion. Please refer to the user manual for the detailed

steps.

(a) Install the VW784 video input board(s) to the video input board slot(s).

(b) Install the VW884 video output board(s) to video output board slot(s).

3

Connect your video source device(s) to the HDMI input port(s) of the

VW784 video input board(s).

4

Connect your video display device(s) to the HDMI output port(s) of the

VW884 video output board(s).

5

(Optional) To control the VW1608 via serial communication, connect your

PC or ATEN Control Box to the unit’s RS-232 port.

6

(Optional) To monitor, preview, and control the real-time content, connect

an HDMI-enabled display to the system HDMI local output port.

7

(Optional) To upgrade firmware, set the video wall background image, or

store the log event data, connect your data storage device(s) to the USB

Type-A port(s).

8

(Optional) To remotely operate the VW1608 via the Web GUI, connect the

Ethernet port of the CPU board to the network using an Ethernet cable.

9

Connect the supplied power cord to the unit’s primary power socket after

powering on all other connected equipment. Turn on the unit’s power

switch, and the primary power LED lights green to indicate the unit is

powered on.

Note:

Optionally install the redundant power module to VW1608’s

redundant power slot for hot-standby operation.

C

Operation

The VW1608 video wall processor can be operated by the following 2

methods:

Front-panel Pushbuttons

1. To control and configure the options available to the unit using the following

pushbuttons:

• Use the navigation buttons (the

Up

and

Down

arrows) to scroll through

the options listed on the LCD display.

• Use the

Enter

button to make your selection.

• Use the

ESC

button to cancel an option or go back to the previous menu

screen.

• Use the

Menu

button to enter the main menu screen.

• Use the

Profile

button to view, load, and apply the profile(s) that you set

in the Web GUI.

• Use the

Local Outpu

t button to configure and preview the content

through the HDMI-enabled display connected to the unit’s system HDMI

local output port.

2. To unlock the on-screen display:

• If password protection is enabled, press any button to start, input your

password using the

Up

or

Down

buttons to cycle through the digits,

press the

Enter

button to advance to the next digit, and finally press

Enter

button to submit the password to unlock the LCD display. To clear

the current digit and go back to the previous digit, press the

ESC

button.

• By default, the password protection is disabled. Please press any button to

start, and then press the Enter button to unlock the LCD display.

3. To access system settings, please unlock the LCD display, press the Menu

button to enter the main

menu

screen, select the function you’d like to

proceed using the

Up

or

Down

buttons, and press the

Enter

button to

enter the submenu screen for further configuration.

4. To assign the input to an output, press the

Menu

button to enter the main

menu screen to select

Operation Mode

, choose the zone to be edited, and

go to

Change Input

to designate the output device/window and the input

source.

5. To set the background, enter the main menu screen and go to

Operation

Mode

>

Background

to choose the system built-in image/your uploaded

image, or to load the image(s) from the connected USB drive. Select your

background image and press the

Enter

button to set the background.

6. To upgrade the firmware of the VW1608 video wall processor, press the

Menu

button to enter the mainmenu screen, and select

F/W Upgrade

to

load the firmware file from the connected USB drive.

Web GUI

Log in the Web GUI to configure advanced system settings, such as profile

schedules, user accounts, and remote real-time viewing.

• For DHCP environment

1. Visit the product page and download

IP Installer

from the

Support and

Downloads

tab.

2. Run

IP Installer

and get the IP address to log in to the Web GUI.

3. Use the default login credentials

administrator

and

password

upon first

login.

• If DHCP is disabled, use the default IP address

192.168.0.6

0 and log in with

default login credentials

administrator

and

passwor

d.

D

LED Indicators

LEDLED ActivityDescription

Power

lights green

Indicates that the primary power module is in

operation.

blinksIndicates that the unit is in sleep mode.

Redundant lights green

Indicates that the redundant power module is

in operation.

Alarmlights red

Indicates that a system error occurred. To obtain

details for the issue, log in to the Web GUI.

The alarm LED goes off once the system error is

fixed.

11

primary power module

12

power switch

13

system HDMI local output

14

USB Type-A ports

15

RJ-45 port (chain out)

16

RJ-45 port (chain in)

17

RS-232 serial port

18

grounding terminal

19

CPU board

20

Ethernet port

VW1608

Front View

VW1608

Side View

VW1608

Rear View

2

1

4

3

Monitor

(Multi-view)

Local User

oror

MonitorVideo Wall

HDMI

HDMI

Ethernet

RS-232

Internet

12

34

Laptop

Remote User

PC

or

2

1

4

3

2

1

4

3

PC

or

ATEN Control Box

Keyboard, Mouse,

& USB Drive

Monitor

Power

Cord

Redundant

Power Supply

PC

Blu-ray

Player

DVD /

Media Player

Video

Camera

or

or

or

VW1608 Rear View

USBHDMI

Power

4

1

2b

2a

3

7

8

9

5

6

Note:

1. The redundant power supply is optional and for hot-standby operation.

2. Currently the USB ports support storage and firmware upgrades.

16 × 8 Modular Video Wall Processor

Quick Start Guide

VW1608

© Copyright 2025 ATEN

®

International Co. Ltd.

ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd.

All rights reserved. All other trademarks are the property of their respective owners.

Released: 12/2025

MISC10000076

12/2025 V1.0

Product specificaties