Atdec VF-AT-W Handleiding

Atdec Niet gecategoriseerd VF-AT-W

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec VF-AT-W (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

Installation Instructions

VF-AT-W

Component Checklist

Focus | Articulated Arm | Wall

M4x10/12/16mm (x4)

Phillips Head

Mounting Screws

Primary Arm

Cable Cover

Secondary Arm

Cable Cover

End CapArm Assembly

Wall Plate

5mm

Allen Key

Nylon Anchor

Plug (x2)

M4 x 12mm

Countersunk

Screw (x2)

M6 x 50mm

Countersunk

Screw (x2)

2.5mm

Allen Key

Display Mounting

Screws

HARDWARE

! IMPORTANT - Install Visidec Focus Articulated Arm Wall as per installation instruction.

! This product supports a maximum load of 8kg (17.6lbs).

! The manufacturer accepts no responsibility for incorrect installation.

IMPORTANT INFORMATION:

Step 1. Check Components

Check what you have received against the component checklist and hardware above.

Step 2. Position Wall Plate

As a guide, it is recommended that the bottom of the Wall Plate be positioned approximately 140mm (5 1/2”)

above the desktop.

For further Ergonomic Guidelines, please refer to the end of the document.

Note: The Focus

Articulated Arm Wall

provides vertical

adjustment of 128mm.

Tools Required:

• Power Drill

• 5.5mm (1/4”) Drill Bit

• 8mm (5/16”) Drill Bit

• Phillips Head Screwdriver

128mm (5”)

140mm (5 1/2”)

Step 3. Installing the Wall Plate

Step 4. Mount Arm Assembly

3.1 Choose the appropriate installation procedure depending on your wall type.

4.1 Unlock the Locking Dial before

inserting the Arm Assembly into the

Wall Plate.

4.2 Slide the Arm Assembly to the

preferred height and lock to secure

the arm.

Lock

Unlock

4.3 Secure the End Cap

with the supplied M4x12mm

Countersunk Screws and

2.5mm Allen Key.

2.5mm Allen Key

End Cap

Wall Plate

Nylon

Anchors Timber

Stud

8mm (5/16”)

Hole 5.5mm

(1/4”) Hole

M6 x 50mm

Countersunk

Screw

M6 x 50mm

Countersunk

Screw

Wall Plate

Arm Assembly

Locking Dial

Wall Plate

M4x12mm

Countersunk Screw

Masonry Timber Stud

Step 5. Mount Display

Step 6. Adjust Height

M4 Phillips Head

Mounting Screws

Option 1: 75x75mm Hole Pattern 100x100mm Hole PatternOption 2:

Note: Extend Arms to

achieve 100x100mm

hole pattern.

5.1 Unlock Lock Dial ensuring both Screen

and Arm Assembly are supported.

5.2 Lift/Lower Screen to the desired height.

Move both Screen and Arm assembly together.

Step 7. Cable Management

7.1 After plugging in your cables, install the Cable Covers.

A. Insert Cable Covers up

into Lock Slots.

B. Push Cable Covers away

from Elbow Joint to secure

in place.

Elbow Joint

‘click’

Lock Slot

5.3 Lock the Lock Dial firmly.

Note: Ensure enough cable

slack is given to allow for

movement.

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	VF-AT-W
Kleur van het product:	Zilver
Montagewijze:	Bureau
Maximale gewichtscapaciteit:	7.9 kg
Draaihoek:	360 °
Pan bereik:	0 - 180 °
Bereik kantelhoek:	-70 - 70 °