Atdec TH-1040-VFM Handleiding

Bekijk gratis de handleiding van Atdec TH-1040-VFM (4 pagina’s), behorend tot de categorie Flat panel steun. Deze gids werd als nuttig beoordeeld door 53 mensen en kreeg gemiddeld 4.1 sterren uit 6 reviews. Heb je een vraag over Atdec TH-1040-VFM of wil je andere gebruikers van dit product iets vragen? Stel een vraag

70

Flat Screen Wall Mount | Full Motion

Installation Instructions

Component Checklist

Hardware

IMPORTANT INFORMATION

! IMPORTANT - Install Telehook Wall Mount as per Installation Instructions.

! Telehook Wall Mount supports Displays weighing up to 20kg (44lbs), with VESA hole configurations:

100x100mm (4”x4”), 200x100mm (8”x4”), 200x200mm (8”x8”)

! The Manufacturer accepts no responsibility for incorrect installation.

Step 1. Check Components

Check you have received all parts against the Component Checklist and Hardware above.

TH-1040-VFM

Step 2. Locate Drilling Postion

WALL

Double-sided

tape (x2)

Drilling Guide

BACK

Un-fold the Drilling Guide and

open the Dust Collector.

Peel away the backing from the

double-sided adhesive tape.

Position the Drilling Guide vertically

onto the wall using a Spirit Level.

Choose the location of your Telehook Wall Mount, ensuring that the wall is structurally sound (for a timber stud

wall, locate the stud using a stud detection device). Use the Drilling Guide to mark out the hole centres.

Dust Collector

Drilling Guide

FRONT

Articulated ArmVESA plate

Concrete

Anchor (x2)

4mm

Allen Key

M4 Washer (x4)M5 Washer (x4)

M4x16mm / M4x25mm (x4 each)

M5x16mm / M5x25mm (x4 each)

M6x16mm / M6x30mm (x4 each)

Coach

Bolt M8 (x2)

Mounting Screws

M4/5

Spacer Bush (x4)

M6/8

Spacer Bush (x4)

Drilling

Guide

TOOLS REQUIRED:

ÊUÊ*ÜiÀÊÀ

ÊUÊ*«ÃÊi>`Ê-VÀiÜ`ÀÛiÀ

ÊUÊ-«ÀÌÊiÛi

ÊUÊÇÊ9/32”) Drill Bit

ÊUÊ££ÊÇ/16”) Masonry Drill Bit

ÊUÊ£ÎÊ1/2”) Socket Wrench or Shifter

Step 6. Cable Management

Remove the Cable Covers as required

using a Phillips Head Screw Driver.

Step 6. Final Adjustment

As TFT Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 03.04.09 ©

Installation Complete

Connect cables to your Display, and route along the arms.

Re-attach the Cable Covers to hold the Cables in place.

TIP: Leave enough slack in the cables

to allow full movement at the joints.

Your Telehook Wall Mount Articulated Arm installation is complete and ready for use.

Cable Covers

Cable Covers

Use the Tool supplied to loosen the

Tension Plate (do not remove).

Rotate the Display as desired, locking the Display into position by

tightening the Tension Plate.

Top

2mm

Allen Key

Cable

Cover

Tightening

Tool

Loosen

Tighten

Tension

Plate

+/- 20°

angular tilt

360° infinite

horizontal rotation

Security Screw

Product specificaties