Atdec AF-AT-NBC Handleiding

Atdec Niet gecategoriseerd AF-AT-NBC

Lees hieronder de đź“– handleiding in het Nederlandse voor Atdec AF-AT-NBC (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
AF-AT-NBC Page 1 of 4
COMPONENT CHECKLIST
A
Notebook tray
assembly
(x1)
E
Primary arm
cable cover
(x1)
F
Secondary arm
cable cover
(x1)
N
Self adhesive
hook & loop
(x4 sets)
B
Monitor
arm
(x1)
C
Pole
assembly
(x1)
D
Rotation
limitor
(x1)
P
Screw
M8 x 30mm
(x1)
K
Pole
top cap
(x1)
L
Bolt through
base
(x1)
M
5mm
Allen key
(x1)
R
Mounting
screws
M4 x 10mm
(x4)
S
Mounting
screws
M4 x 12mm
(x4)
T
Mounting
screws
M4 x 16mm
(x4)
Q
Security
Screw
M4 x 16mm
(x1)
H
Steel
washer
(x1)
I
Cable
stop
(x2)
O
Screw
M8 x 60mm
(x1)
G
Desk clamp
assembly
(x1)
J
Cable
clip
(x1)
U
VESA
head
(x1)
Installation Guide
AF-AT-NBC
Notebook Monitor Arm
Combo Mount
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
WEIGHT RANGE
• Power Drill
• Drill Bit
• Phillips Head Screwdriver
0 - 8kg
(0 - 17.6lbs)
AF-AT-NBC Page 2 of 4
1. Desk overview
The desk clamp bracket
can be repositioned to
suit different mounting
surface thicknesses.
1.1 1.2 Default Inverted
2. How to reconfigure desk clamp
2.1 Remove screws
(M8 x 16mm Countersunk screw)
2.2 Remove clamp plate Invert bracket Replace clamp plate Reattach bracket2.3 2.4 2.5
Pressure
Plate
M10 Desk
Clamp Screw
5mm Allen
Key
M8 x 30mm
Countersunk
screw Tighten
firmly
3.2 Place in desired location Screw pressure plates 3.3
in and .tighten firmly
Drill 9mm hole in desired post
position on work surface.
3.1 Attach clamp to post
3. Post mount configuration Bolt through4.
9mm
(3/8”)
25mm
offset
MIN THICKNESS - 0mm (0”)
MAX THICKNESS - 39mm (1.5”)
MIN THICKNESS - 35mm (1.4”)
MAX THICKNESS - 76mm (3”)
5. Installing bolt through
5.1 Attach plate to post
Align rear hole with
hole on desk
5mm
Allen key
M8x60mm
Screw
Bolt
through
plate
6. Install VESA monitor head
Optional Spacers
(may be required
for recessed and
uneven surfaces)
VESA monitor
head
Screen
M4x10/12/16mm
Phillips head
mounting screws
6.1 Install VESA monitor head as shown.
100mm
100mm
AF-AT-NBC Page 3 of 4
1st Handgrip
7. Mount Notebook Tray Arm
7.1 Unlock 1st handgrip
and remove from
pole assembly
Notebook Tray
& Arm Assembly
7.2
Unlock 2
nd
handgrip
and raise so that
handgrip tab protrudes
7.3 OPTIONAL ROTATION
LIMITER Insert rotation
limiter for 180ďż˝ rotation
around mounting pole
7.4 Slip the notebook
tray & arm assembly
over the handgrip tab
and then onto the pole
7.5 Slide the arm
assembly and handgrip
down the pole before
locking the handgrip at
the desired height
Arm Assembly
8. Install arm assembly
Handgrip
Tab
5mm
Allen key
Pole
top cap
8.1 Reinstall handgrip so that
handgrip tab protrudes
8.4 Slide the arm assembly and
handgrip down the pole before locking
the handgrip at the desired height
8.5 Insert pole
top cap into
pole. This is also
where the allen
key is stored.
8.3 Slip the arm
assembly over the
handgrip tab and
then onto the pole
8.2 OPTIONAL ROTATION LIMITER Insert rotation
limiter for 180ďż˝ rotation around mounting pole
9. Mounting Monitor
10. Install Notebook
VESA monitor head
Arm assembly
9.2 OPTIONAL SECURITY SCREW
Ensure the monitor is supported,
then loosen the monitor head
screw with the 5mm allen key and
tilt screen up before installing the
m4 x 16mm security screw into the
security screw hole
Note: Support Screen
when adjusting tilt.
9.1 Insert VESA monitor head into the
receptacle in the arm assembly
5mm Allen key
Phillips head
screwdriver
Loosen
Tighten
Security screw
hole
M4 x 16mm
Security screw
Monitor head
screw
10.1 Adjust the support
tabs to suit the width of
the notebook computer
ensuring that cable ports
are not obstructed
10.2 To increase stability, use the self
adhesive Hook-and-Loop Fasteners supplied
• Peel off the backing paper to the fasteners
• Attach fasteners to both the notebook tray
and computer
• Ensure that each set of fasteners are
correctly aligned i.e. Hook to loop

Product specificaties

Merk: Atdec
Categorie: Niet gecategoriseerd
Model: AF-AT-NBC

Heb je hulp nodig?

Als je hulp nodig hebt met Atdec AF-AT-NBC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Atdec

Atdec

Atdec AWMS-NDB Handleiding

11 Maart 2024
Atdec

Atdec AF-AN-P Handleiding

9 Juli 2023
Atdec

Atdec AF-WD-P Handleiding

9 Juli 2023
Atdec

Atdec TH-VWP-160 Handleiding

9 Juli 2023
Atdec

Atdec AWMS-3-137140-C Handleiding

9 Juli 2023
Atdec

Atdec SD-POS-HA Handleiding

8 Juli 2023
Atdec

Atdec VTB-FD Handleiding

8 Juli 2023
Atdec

Atdec Ultra-Slim Handleiding

8 Juli 2023
Atdec

Atdec TH-3060-LPF Handleiding

8 Juli 2023
Atdec

Atdec TH-32-60-UTM Handleiding

8 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024