Atdec ADB-VWP Handleiding

Atdec Niet gecategoriseerd ADB-VWP

Lees hieronder de 📖 handleiding in het Nederlandse voor Atdec ADB-VWP (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6

ADB-VWP Page 1 of 6

Pop-out Video Wall Mount

! Important: The wall structure must

be capable of supporting at least ve

times the weight of the at-panel.

If not, the wall structure must be

reinforced.

COMPONENT CHECKLIST

Installation Guide

ADB-VWP

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

REQUIRED TOOLS

• Power Drill

• 6.5mm (1/4 ”) Drill Bit

• 10mm (3/8

”) Drill Bit

• Phillips Head Screwdriver

• Stud Finder

• 1/2” Socket

• Socket Wrench

• Pencil

0 - 50 kg

(0 - 110lbs)

WEIGHT RANGE

M5x16mm

Screw (x4)

M8 Washer

(x6)

M8x30mm

Screw (x4)

M6x16mm

Screw (x4)

Anchor

(x6)

M5/M6

Washer

(x4)

M6x30mm

Screw (x4)

M8x13mm

Spacer

(x8)

M8x5mm

Spacer

(x8)

M8x16mm

Screw (x4)

M8x15mm

Screw (x4)

(installed)

5mm

Allen Key

(x1)

M5x30mm

Screw (x4)

Coach Bolt

(x6)

M8x50mm

Screw (x4)

Mounting Base

(x1)

Left and Right

Mounting Bracket

(x1)

600mmx400mm

Adaptor

(x2)

ADB-VWP Page 2 of 6

INSTALLATION SAFETY INSTRUCTIONS

CAUTION: THIS MOUNT IS INTENDED FOR USE ONLY

WITH THE MAXIMUM WEIGHTS INDICATED. USE WITH

DISPLAYS HEAVIER THAN THE MAXIMUM INDICATED MAY

RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.

Do not attempt to install this product until all

instructions and warnings have been read and

properly understood.

Please keep these instructions for future reference.

Please check carefully to make sure there are no

missing or defective parts - defective parts must

never be used.

Atdec Pty Ltd, its distributors and dealers are not

liable or responsible for damage or injury caused

by improper installation, improper use or failure to

observe these safety instructions.

In such cases, all guarantees will expire.

GENERAL

Atdec Pty Ltd recommends that a professional AV

installer or other suitably qualified person install

this product. Great care must always be taken

during installation as most AV equipment is of a

fragile nature, possibly heavy and easily damaged if

dropped.

If you do not fully understand the instructions or

are not sure how to install this product safely, then

please consult a professional for advice and/or to

install this product for you. Failure to mount this

product correctly may cause serious injury or death

both during installation and at any time thereafter.

Do not mount any AV equipment that exceeds

the specific weight limit of the product you are

installing.

This weight limit will be clearly stated on each

product and its packaging and will vary from

product to product.

PRODUCT LOCATION

Please pay careful attention to where this product

is located. Check load capacity of wall prior to

installation as some walls are not suitable for

installation. Designed for indoor use, this mount is

suitable for public or home installation. If located

in a public or frequently populated area ensure

that the product is out of the immediate reach of

people. If any AV equipment is to be suspended

over the likely path or location of people then great

care should be taken to secure all parts of

the

installation from falling. If you install this product

on drywall it must be securely fixed to a wooden

stud, concrete block or other permanent structure

behind the drywall board.

Installing on drywall boards alone will not support

the weight of most AV equipment.

When drilling holes in walls it is essential to avoid

contact with electrical cables and water or gas

pipes contained within. Use of a good quality

live wire detector and hidden object locator is

therefore recommended.

Only drill into structures when you are sure it is

safe to do so.

FIXING HARDWARE

It is highly recommended that all wall fixing screws

be used where supplied and that the purpose of all

other fixing hardware is fully understood. In some

cases more AV equipment fixing hardware will

be supplied to accommodate different models of

equipment and set up configurations.

The installer must be satisfied that any supplied

fixing hardware is suitable for each specific

installation. If any fixing screws or included

hardware are deemed not sufficient for a safe

installation then please consult a professional or

your local hardware store.

HAZARD LIMITATION

When routing cables take advantage of any built

in cable management features that the product

might provide and ensure that all cables are tidy

and secure. Check to see that any moving aspect

of product can do so unhindered by any cabling.

Some products have moving parts and the

potential to cause injury through the crushing or

trapping of fingers or other body parts.

Particular attention to the nature of moving parts is

required especially when assembling, installing and

adjusting during set up.

Immediately after installations double-check that

the work done is safe and secure. Double-check

all necessary fixings are present and are of ample

tightness.

It is recommended that periodic inspections of

the product and its fixing points are made as

frequently as possible to ensure that safety is

maintained. If in doubt consult a professional AV

installer or other suitably qualified person.

ADB-VWP Page 3 of 6

Directional Mounting Arrow

The directional mounting arrow

stamped into the ADB-VWP mount

indicates which is the top edge.

1. Mounting to wooden studs

A. Two people are recommended for this step;

one person to level the mount and another

person to mark the wall stud location.

i Place the mount against the wall in the

desired viewing location.

ii Adjust the mount to align the mount slots in

the mount with the centre of the wall studs.

iii Level the mount.

iv Use a pencil to mark the upper right

mounting location along the centre of the

wall stud.

B. Two people are recommended for this step;

one person to level the mount and another

person to drill the pilot holes.

Drill a “pilot hole” in the centre of each of

the marks with a power drill and a 1/

4”

(6.5mm) drill bit.

C. Two people are recommended for this step;

one person to level the mount and another

person to fasten the screws.

i Insert one (1) coach bolt and one (1) M8

washer into each pilot hole.

ii Tighten all coach bolts using a socket wrench

and 1/2” socket.

Only use 1/

4” (6.5mm) drill bit

when drilling the pilot holes

Do not overtighten the coach bolts

when attaching the mount to the wall.

Improper installation may result in

personal injury or propery damage.

Orientation

Mounting Safety

Two people are recommended

to install the mount.

Product specificaties

Merk:	Atdec
Categorie:	Niet gecategoriseerd
Model:	ADB-VWP
Kleur van het product:	Zwart
Breedte:	510 mm
Hoogte:	544 mm
Gewicht verpakking:	15500 g
Breedte verpakking:	587 mm
Diepte verpakking:	650 mm
Hoogte verpakking:	100 mm
Soort:	Vaste vloerstandaard
Materiaal behuizing:	Staal
Montagewijze:	Muur
Maximale gewichtscapaciteit:	50 kg
Paneelmontage-interface:	100 x 100,100 x 200,200 x 100,200 x 200,200 x 300,200 x 400,200 x 600,300 x 200,300 x 300,400 x 200,400 x 400,400 x 300,400 x 600,600 x 200,600 x 600 mm
Montage interface compatibiliteit (min):	100 x 100 mm
Montage interface compatibiliteit (max):	600 x 400 mm
Aantal displays ondersteund:	1
Verbeterd kabelbeheer:	Ja
(Buitenste) hoofdverpakking hoogte:	110 mm
(Buitenste) hoofdverpakking breedte:	600 mm
(Buitenste) hoofdverpakking brutogewicht:	15500 g
(Buitenste) hoofdverpakking lengte:	660 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Maximale schermgrootte:	- "
Afstand tot de muur (min):	88 mm
Afstand tot de muur (max.):	267 mm