Asus ROG Chariot X Handleiding

Bekijk gratis de handleiding van Asus ROG Chariot X (9 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen. Heb je een vraag over Asus ROG Chariot X of wil je andere gebruikers van dit product iets vragen? Stel een vraag

SL301 ROG CHARIOT Installation Guide

Package Contents

A

Installing the Lumbar cushion

C

Other features

E

Assembling your chair

B

Put on the gloves before installation.

One by one, insert and push the wheels into the

base.

Insert the hydraulic lift cylinder into the center

hole of the base. Remove the red protective cap

on top if there was any.

Place the telescoping cover on the top of the

hydraulic lift cylinder.

Armrests normally do not

distinguish sides unless labeled

otherwise.

For models with armrest pre-

assembled, please skip this step.

Remove the pre-assembled bolts and washers

(

1

&

3

). Place the 4 large washers (

1

)

between the armrest mounting bar (

2

) and the

seat base. Hold the armrest in place, then insert

and tighten all 4 bolts (

3

). Use the hex key to

tighten them all, and repeat on the other side.

Use the hex key to remove the pre-assembled

bolts and washers from the backrest.

Remove the protective foam covers from the

brackets of the seat base. Then position the

backrest carefully between the brackets. Insert

and attach the 4 bolts (2 on each side) you

removed in step 5 by hand rst. Then use the hex

key to tighten them. Start with the two bolts on

the top of each side, then the bottom two.

Q23175 / Revised Edition V2 / January 2024

Install the side covers and tighten the bolts. (The

covers are marked “L” for the left side and “R” for the

right on the inside.)

Now ip the chair over, facing down. Then remove

the 4 pre-mounted bolts from the underside with

washers.

Repeat the step above to install the control unit,

and then place the nut to mount the hydraulic

lift cylinder facing the back of the seat (where the

backrest is installed).

Insert top of the hydraulic lift cylinder into the

mounting hole on the control unit, and then turn

the chair over in upright position. (Two-person

handling required for your safety)

Hanger at the back of the

chair for hanging your bags,

clothes, cups and more.

Maximum load: 2kg

Please do not hang items

over 2kg.

Lighting up your chair

1. Place your power bank into the

packet at the back of the chair.

2. Connect the USB Type-A

connector to your power bank.

The packet is attached to your

chair with Velcro. You can easily

remove and take it away.

a

Using the RGB controller

1. Aura RGB Lighting: On / Eect / O

Press repeatedly to power the Aura RGB LEDs on or o,

or cycle through the current 7 eects: (1) rainbow (2)

breathing (3) color cycle (4) wave (5) glowing Yo-Yo (6)

strobing (7) static

Press the Aura RGB Lighting button for 3 seconds to

terminate the lighting.

Press it to wake up again or reconnect your powerbank

will keep its previous setting.

NOTE: Your powerbank may automatically adjust its

output when the lighting is terminated. Disconnect

and reconnect it if the Aura RGB Lighting cannot wake

up after toggling it back on.

2. Aura RGB color

Press repeatedly to cycle through the following 8

striking colors: (1) red (2) orange (3) yellow (4) green (5)

blue (6) indigo (7) purple (8) pink

NOTE: This feature is only available on the following

Aura RGB eects: (2) breathing (6) strobing (7) static

3. Aura RGB speed: Slow / Medium / Fast

Press repeatedly to cycle through the following 3 color

eect speeds: (1) Slow (2) Medium (3) Fast

NOTE: This feature is only available on the following

Aura RGB eects: (1) rainbow (2) breathing (3) color

cycle (4) wave (5) glowing Yo-Yo (6) strobing

4. Aura RGB brightness: 50% / 75% / 100%

Three brightness levels. The brightness can be switch

by simple tap to t the environment lighting and

preference.

5. Reset to factory mode

Press the button (2) and button (4) simultaneously to

reset your chair to its factory defaults.

b

1

2

3

4

NOTE: The illustrations are for reference only and may dier from your

actual chair in appearance and features.

1.

Backrest

5.

Wheels

9.

Hydraulic lift cylinder

2.

Seat base

6.

Side covers with bolts

10.

Telescoping cover

3.

Lumbar cushion

7.

Control unit

11.

Hex Key

4.

Wheel base

8.

Gloves

12.

Spare bolt

Place the lumbar cushion against the backrest to

serve as lumbar support.

DO NOT remove the non-detachable controller as this

will void the warranty.

D

Rating: 5V1A

SL301W ROG CHARIOT Installation Guide

Product specificaties