Astralpool RPX Robotic Pool Cleaner Handleiding

Astralpool Diversen RPX Robotic Pool Cleaner

Lees hieronder de 📖 handleiding in het Nederlandse voor Astralpool RPX Robotic Pool Cleaner (19 pagina's) in de categorie Diversen. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/19

Installation and Operating Instructions

RPX Robotic Pool Cleaner

Product 11714

Product Inst 323

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL THE INSTRUCTIONS

CAUTION: Do not plug the power supply into a grounded outlet or do not switch the

pool cleaner “ON” if it is not fully immersed in water. Operating the cleaner out of water

will cause severe damage immediately and will result in loss of warranty.

Allow the cleaner to remain in the pool for 15 to 20 minutes following the end of its

cleaning cycle. This will allow the motors to cool adequately. Do not leave the cleaner

in the pool all the time. Always remember to turn the power supply “OFF” and unplug it

from the power outlet before removing the cleaner from the pool.

WARNING: The cleaner must not be used when people are in the water. For use

with swimming pool only

Safety Note

- The unit must be supplied through a residual current device (RCD) having a rated

residual operating current not exceeding 30 mA

- The connection to the branch circuit should be consistent with the local and national

wiring rules (electrical code).

- Mishandling of the unit can result in leakage of lubricants.

- If the supply cord is damaged, it must be replaced by the manufacturer’s service

agent or a qualified and trained person in order to avoid hazards.

Dear Customer,

Thank you for choosing our product to clean your pool. We hope that you will enjoy

using your new robot to maintain your swimming pool for years to come.

Before you begin to use your robot, please take a few minutes to carefully read these

operating instructions.

Again, thank you for choosing our product.

Components

Your new automatic pool cleaner contains:

- The robotic pool cleaner with its floating cable.

- The Power Supply (transformer).

- Caddy

Please read this manual completely before operating your pool cleaner.

While the appearance of your cleaner and some of its components may differ from those

shown here, the function of the cleaner, operating procedures and maintenance

practices are the same.

WARNING: A Ground Fault Current Interrupter (GFCI-USA) or a Residual Current

Device (RCD-EUROPE) must be installed to protect your electric outlet and prevent

any possible electric shock.

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety. Children should be supervised to ensure that they do not

play with the appliance.

Side Plate

Handle

Handle Lock

Mechanism

Drive Track

Scrubbing Brush

Unit Body

Outlet Top

SAVE THESE INSTRUCTIONS

12 cm

(4 inch)

3.6m/11.8ft

1. Place the power supply (transformer) at least 3.6 meters / 11.8 feet from the pool and at

least 12 cm / 4 Inch above the surface (fig.1). The transformer will supply low voltage to

the cleaner.

2. Uncoil the cable.(fig.1a)

3. For proper operation, lock the moveable handle diagonally across the top of the

cleaner's body. Push down on the handle lock mechanism and slide the handle all the

way to the end (recommended one slot before the end), then release the lock.

Depending on your model, the handle lock button might be vertical or horizontal

(fig.2a, 2b). The handle will remain fixed in this position. Repeat this process on the

other side of the cleaner.

Remember, the handle must be fixed diagonally (fig.2c)

unit

2c2aHandle lock vertical Handle lock horizontal

Operating the pool cleaner

4. Place the unit in the water. Turn the unit

side to side in the water to allow air to

escape from the body and then let the

cleaner sink to the bottom of the pool

(fig.3). Then, spread the cable over the

surface of the pool as evenly as possible

(fig.1).

5. Plug the cable into the power supply. Make sure the key on the plug corresponds

exactly with the key slot on the socket of the power supply (fig. 3a).

Plug the power supply into a grounded outlet. Ensure that the electric outlet has been

properly grounded (fig.3b). Press the “ON” button on the power supply. The light will

glow indicating that the system is “ ON “ and the pool cleaner will start the cleaning

cycle. The unit keeps record of the number of cleaning cycles. Only an authorized

service center can display the accumulated cleaning cycles. (See details on the next

page)

Product specificaties

Merk:	Astralpool
Categorie:	Diversen
Model:	RPX Robotic Pool Cleaner

Heb je hulp nodig?

Als je hulp nodig hebt met Astralpool RPX Robotic Pool Cleaner stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Diversen Astralpool

Astralpool RTX Robotic Pool Cleaner Handleiding

2 September 2023

Astralpool Dolphin Easykleen Handleiding

2 September 2023

Astralpool RPX Robotic Pool Cleaner Handleiding

2 September 2023

Handleiding Diversen

Nieuwste handleidingen voor Diversen

Fysic FHP-160 Handleiding

23 Oktober 2023

Fysic FC-18 Handleiding

23 Oktober 2023

Fysic FC35 Handleiding

23 Oktober 2023

Ideen Welt Led stekkerdoos verlichting 323043-G Handleiding

17 Oktober 2023

Ideen Welt Thermo koeltas Handleiding

17 Oktober 2023

Ideen Welt Massage MV-25 Handleiding

17 Oktober 2023

Ideen Welt LED sensor LX-LD-P300 Handleiding

17 Oktober 2023

Ideen Welt ZF6865 8 LED Camping lamp Handleiding

17 Oktober 2023

Ideen Welt Muis snoerloos Handleiding

17 Oktober 2023

Ideen Welt Koffer weegscaal Handleiding

17 Oktober 2023