Arecont Vision SurroundVideo AV12366DN Handleiding
Arecont Vision
Bewakingscamera
SurroundVideo AV12366DN
Bekijk gratis de handleiding van Arecont Vision SurroundVideo AV12366DN (21 pagina’s), behorend tot de categorie Bewakingscamera. Deze gids werd als nuttig beoordeeld door 30 mensen en kreeg gemiddeld 4.7 sterren uit 15.5 reviews. Heb je een vraag over Arecont Vision SurroundVideo AV12366DN of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/21
Arecont Vision SurroundVideo® WDR Camera Installation Manual
1 | P a g e
Arecont Vision SurroundVideo® WDR Camera Installation Manual
1 | P a g e
AV12186DN/AV12366DN SurroundVideo® Installation Manual
Inside the box:
A. Arecont Vision AV12186DN camera
B. Mounting template
C. Security L-key
D. 1.5mm Hex L-key
E. Power cable
F. I/O Cable
G. Pack of four (4) screws and four (4)
anchors.
NOTE: Anchors and screws are good to be used for
concrete, wall block and red bricks. Screws by
themselves can be used in wood.
Not included but needed:
#2 Phillips head screw driver
Image 1
How to Mount the Camera
1. Remove camera and hardware from the
b . ox
2. Using the Mounting template, prepare the
mounting provisions for camera
installation. NOTE: the 19.5mm diameter
hole on the Mounting template is where
the Ethernet cable will be exiting the
AV12186DN camera, align accordingly.
If using the side conduit hole, please see
step 7 below.
3. Using Security L-key, loosen the four (4)
screws securing the dome cover . (Image 2)
Remove vandal resistant dome cover. NOTE:
Do not remove screws from the dome cover.
Image 2
A
B
C
D
E
F
G
Arecont Vision SurroundVideo® WDR Camera Installation Manual
2 | P a g e
4. Run Ethernet cable through the hole on the
bottom of the camera and plug it (Image 3)
into the RJ45 port.
5. If the camera is powered by a separate
outside AC or DC power source run the ,
supplied power cable through the hole and
connect it to 2-pos. AC/DC power connector
inside the camera (Image 3). NOTE: Make
sure that your installation of wires complies
with Electrical Code of the local government,
where the camera is installed and no bare
wires are exposed.
6. Align the holes in the camera with the
prepared holes on the mounting surface.
Attach the camera to the mounting surface
with the wood screws or any optional
hardware suitable for the mounting surface.
Image 3
7. If you are using the side conduit opening,
remove the conduit plug by first removing the
socket set screw using 1.5mm Hex L-key
(Image 4).
Image 4
Image 5
Adjust Camera Tilt, Pan and Focus:
8. To adjust the gimbal tilt, use #2 Phillips
screwdriver to loosen t screws both sides of wo on
the Gimbal, no more than two full turns (Image 5)
CAUTION: Do not remove the screws!
HOLE
POWER
RJ- 45
Product specificaties
| Merk: | Arecont Vision |
| Categorie: | Bewakingscamera |
| Model: | SurroundVideo AV12366DN |
Heb je hulp nodig?
Als je hulp nodig hebt met Arecont Vision SurroundVideo AV12366DN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Bewakingscamera Arecont Vision
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
Handleiding Bewakingscamera
- Compro
- Provision ISR
- Nextech
- EVE
- Eufy
- Notifier
- YoloLiv
- ETiger
- Pioneer
- Dorr
- Wisenet
- Sonoff
- Setti+
- Elro
- Inkovideo
Nieuwste handleidingen voor Bewakingscamera
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025