Aqara Ceiling Light T1M Handleiding
Aqara
Verlichting
Ceiling Light T1M
Bekijk gratis de handleiding van Aqara Ceiling Light T1M (8 pagina’s), behorend tot de categorie Verlichting. Deze gids werd als nuttig beoordeeld door 85 mensen en kreeg gemiddeld 4.5 sterren uit 43 reviews. Heb je een vraag over Aqara Ceiling Light T1M of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
CAUTION:
If it does not light up after turning on the power, please confirm whether the
installation and wiring of the lamp are correct. The light source in this luminaire
should be replaced by the manufacturer or its service agent or a similarly qualified
person.
Unstable ceiling Warning: Risk of electrical shock!
Installation Manual
Warning: Before installing the lamp, the power must be cut off to prevent electric shock.
Installation method A
1. Turn off the power at the circuit breaker and the light switch. Install the mounting
brackert on the junction box using the junction box screws. Ensure that the two
mounting bracket screws are pointing away from the ceiling.
2. Place the base on the mounting bracket. Temporarily screw the base of the
luminaire to the mounting bracket using the butterfly screws.
3. Mark on the ceiling the 3 locations where the holes will be drilled and remove the
base.
4. Drill pilot holes in the ceiling with a drill bit. And push wall anchors into the holes.
5. Slowly place the wires in the connection box. Align the holes in the base of the
luminaire with the mounting bracket screws, raise the base and turn it
counterclockwisee, locking it into place. Tighten the buttrerfly screws to fix the light
fixture to the ceiling and fasten the 3 retaining screws into the wall anchors.
6. Strip the wires by 6-8mm, and connect the live wire,ground wire, and neutral
wire to the wiring holes marked with L, , and N in the ceiling lamp in sequence.⏚
Stripping wire
Warning:
Risk of electrical chock!
This product must be grounded!
7. Hold both sides of the lampshade with both hands, align the base and gently buckle
it in, totate the lampshade clockwise to make it firmly installed with the base, and the
installation of the ceiling lamp is completed.
Installation method B
1. Cut off the power supply; unpack, take out the accessory package, hold the lampshade with
both hands as shown in the figure below, and open the lampshade counterclockwise to take out the
base.
2. Mark the installation holes on the ceiling according to the installation position of
the ceiling lamp with the base., and then drill the holes with an electric drill (the
drilling depth is ≥ 40mm).
3. After drilling the holes, drive the wall anchors into the holes, and lead the wires
out of the holes on the base.
Product specificaties
| Merk: | Aqara |
| Categorie: | Verlichting |
| Model: | Ceiling Light T1M |
Heb je hulp nodig?
Als je hulp nodig hebt met Aqara Ceiling Light T1M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Verlichting Aqara
8 Augustus 2024
31 Juli 2024
19 Juli 2024
15 Juli 2024
Handleiding Verlichting
- Expolite
- SereneLife
- DMT
- Gembird
- HQ
- Peerless-AV
- Neewer
- Doughty
- Geemarc
- Sigma
- Viessmann
- Enttec
- Gingko
- Alora
- Gardena
Nieuwste handleidingen voor Verlichting
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025