Apc NetBotz Camera Pod 165 Handleiding

Apc Bewakingscamera NetBotz Camera Pod 165

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc NetBotz Camera Pod 165 (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
NetBotz Camera Pod 165
Installation and Quick Start
NBPD0165
Product Description
The APC by Schneider Electric® NetBotz Camera Pod 165 is a motion-
sensitive camera capable of sending image data through a connection to
a NetBotz Rack Monitor 750. The Camera Pod 165 can be triggered by
the appliance in response to a number of environmental alarms or
events, such as a temperature spike or the action of opening a door. The
Camera Pod 165 can also provide constant surveillance of an area or
entrance.
Receiving
Inspect the package and contents for shipping damage. Make sure all
parts were sent. Immediately report any shipping damage to the shipping
agent. Report missing contents, product damage, or other problems with
the product to APC by Schneider Electric or your Schneider Electric
reseller.
NOTICE
The equipment contains, and the software enables, visual recording
capabilities, the improper use of which may subject you to civil and criminal
penalties. Applicable laws regarding the use of such capabilities vary between
jurisdictions and may require, among other things, express written consent
from recorded subjects. You are solely responsible for insuring strict
compliance with such laws and for strict adherence to any/all rights of privacy
and personalty. Use of this software for illegal surveillance or monitoring shall
be deemed unauthorized use in violation of the end user software agreement
and result in the immediate termination of your license rights thereunder.
Customer support and warranty information is available at
www.apc.com.
© 2019 APC by Schneider Electric. All rights reserved.
990-5974A-001 9/2019
Physical Description
Item Description
RJ-45 port For network and Power Over Ethernet (PoE) connections
Network LEDs Link LED: turns green to indicate a good network connection.
Activity LED: flashes orange to indicate network activity
Power jack Reserved for future use
Alarm In/Out Reserved for future use
Mounting hole Used to mount the Camera Pod 165
Micro SD card slot Reserved for future use
Reset button Press for at least 20 seconds to reset to factory defaults
aem0555a







Inventory
Item Description Quantity
Camera Pod 165 1
Rubber bracket cover 1
T-bar mounting plate 1
Set screw* 1
Hex wrench* 1
Ball-joint adjuster arm 2
Extender arm 2
Mounting plate 1
*Not used
aem0556a
   
 
Installation
Choose the mounting option (rack, wall, or ceiling) that meets your needs.
Then connect the Camera Pod 165 to your NetBotz appliance or to the
network.
Rack mount
Use #8 sheet-metal screws (not provided) to secure the camera pod. Use
a #32 drill to make four 2.94 mm (0.116 in) pilot holes in the rack.
Ceiling mount
aem0283c
aem0285c
Wall mount
Use #8 screws (not provided) to secure the camera pod.
Connect the Camera Pod 165 to a NetBotz 5.x appliance
Use a Power over Ethernet (PoE) ready, CAT-5 Ethernet cable to
connect the Camera Pod 165 to the Private LAN port of your appliance.
Connect the Camera Pod 165 to your network
If you do not connect the Camera Pod 165 to an appliance, you can use
a PoE-ready CAT-5 Ethernet cable, PoE equipment, and a network
switch to connect the Camera Pod 165 to your network.
Configuration
See the on User Guide www.apc.com for instructions to configure the
camera pod in the Web User Interface (UI) of your NetBotz appliance.
The Camera Pod 165 is automatically set to have a dynamic IP address
assigned via DHCP. If the Camera Pod 165 is not connected directly to
an appliance, you can use Device Search to view the current IP address
of the Camera Pod 165 or to assign it a static IP address.
Use Device Search to discover the IP address
1. Connect your computer to the same subnet as the
Camera Pod 165.
2. Go to the CameraPod 165 product page on www.apc.com.
Download and open the executable file.DeviceSearch
3. In the Device Search window, select All NetCard from the Local
Broadcast Device Search drop-down list and click . Wait for the
search to finish. You can identify you Camera Pod 165 by its MAC
address, which you can find on the back of the unit.
Use Device Search to set a static IP address
1. Follow the instructions to discover the IP address of the
Camera Pod 165.
2. In the window, right-click the Camera Pod 165, Device Search
and select to open the window.Network Setup Network Setup
3. Select Static IP, and enter the static , default gateway IP address
(Gateway), Subnet Mask (Netmask), and Domain Name System
server ( ) for your Camera Pod 165. DNS
aem0284c
Change the password
NOTE: The Camera Pod 165 Web UI is only used to change the password and
upgrade the firmware.
When connecting an un-configured camera pod directly to an appliance, you
do not have to change the password—the appliance configures the camera
security automatically. Password changes are only required for remote
connections to an appliance.
1. Enter the camera pod IP address in the URL address bar of your Web
browser, then log on using the default user name and password ( apc
and ). apc
2. When prompted, enter a new password in the Admin password and
Confirm password Save fields, then click . The password is case
sensitive and must be at least 8 characters longs.
To change the password after first use, Log on to the camera pod Web UI, then
select System > Security > User. Enter the new password in the Admin
password Confirm password Save and fields, then click .
To recover a lost password, press the reset button for 20 seconds, wait 5-10
minutes for the camera pod to restart, then repeat this procedure.
Upgrade the firmware
NOTE: The Camera Pod 165 Web UI is only used to change the password and
upgrade the firmware.
1. Download the latest firmware version from the applicable product page
of www.apc.com.
2. Enter the camera pod IP address in the URL address bar of your Web
Browser. Log in, then select . System > Software Upgrade
3. Select , then browse to the appropriate firmware file.Browse...
4. Click , then wait for the upgrade to complete. If you lose Upgrade
connection to the Web UI, refresh the page.
5. Select System > Software Version to view the current firmware version
and verify that the upgrade was successful.
Adjust the focus
Remove the lens cover. Twist the lens to the left and right until the image
becomes clear.
Specifications
Electrical
Power Source Power over Ethernet
Power Consumption: Operation
(802.3af) system
3.7 W
Mechanical
Dimensions (H x W x L) 96.51 x 56 x 61.4 mm (3.78 x 2.2 x 2.42 in.)
Weight 120 g (0.26 lb)
Environmental
Operating temperature 0–45°C (32–113° F)
Humidity 10–90%, no condensation
Compliance
Safety CE (LVD)
EMC FCC / CE (EMC Directive)
Two-Year Factory Warranty
This warranty applies only to the products you purchase for your use in accordance with this manual.
Terms of warranty
APC by Schneider Electric warrants its products to be free from defects in materials and workmanship for
a period of two years from the date of purchase. APC by Schneider Electric will repair or replace
defective products covered by this warranty. This warranty does not apply to equipment that has been
damaged by accident, negligence or misapplication or has been altered or modified in any way. Repair or
replacement of a defective product or part thereof does not extend the original warranty period. Any parts
furnished under this warranty may be new or factory-remanufactured.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly registered the product. The
product may be registered at the APC by Schneider Electric Web site, www.apc.com.
Exclusions
APC by Schneider Electric shall not be liable under the warranty if its testing and examination disclose
that the alleged defect in the product does not exist or was caused by end user’s or any third person’s
misuse, negligence, improper installation or testing. Further, APC by Schneider Electric shall not be liable
under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage
or connection, inappropriate on-site operation conditions, corrosive atmosphere, repair, installation,
exposure to the elements, Acts of God, fire, theft, or installation contrary to APC by Schneider Electric
recommendations or specifications or in any event if the APC by Schneider Electric serial number has
been altered, defaced, or removed, or any other cause beyond the range of the intended use.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR
OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR
IN CONNECTION HEREWITH. APC BY SCHNEIDER ELECTRIC DISCLAIMS ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR
PURPOSE. APC BY SCHNEIDER ELECTRIC EXPRESS WARRANTIES WILL NOT BE ENLARGED,
DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, APC
BY SCHNEIDER ELECTRIC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN
CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET
FORTH ABOVE CONSTITUTE APC BY SCHNEIDER ELECTRIC’S SOLE LIABILITY AND
PURCHASER’S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. APC BY
SCHNEIDER ELECTRIC WARRANTIES EXTEND ONLY TO PURCHASER AND ARE NOT
EXTENDED TO ANY THIRD PARTIES.
IN NO EVENT SHALL APC by Schneider Electric, ITS OFFICERS, DIRECTORS, AFFILIATES OR
EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR
PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE
PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF
FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC by Schneider Electric HAS BEEN
ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, APC by
Schneider Electric IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE,
LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA,
COSTS OF SUBSTITUENTS, CLAIMS BY THIRD PARTIES, OR OTHERWISE.
NO SALESMAN, EMPLOYEE OR AGENT OF APC by Schneider Electric IS AUTHORIZED TO ADD
TO OR VARY THE TERMS OF THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF AT
ALL, ONLY IN WRITING SIGNED BY AN APC by Schneider Electric OFFICER AND LEGAL
DEPARTMENT.
Warranty claims
Customers with warranty claims issues may access the APC by Schneider Electric customer support
network through the Support page of the APC by Schneider Electric Web site, www.apc.com/support.
Select your country from the country selection pull-down menu at the top of the Web page. Select the
Support tab to obtain contact information for customer support in your region.
Radio Frequency Interference
USA.FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference. The user will bear sole responsibility for correcting
such interference.
Canada.ICES
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
European Union
This product is in conformity with the Electromagnetic Compatibility (EMC) requirements set forth by the
EU directive 2014/30/EU of the European parliament and of the council of 26 February 2014 on the
harmonization of the laws of the Member States relating to electromagnetic compatibility.
This product has been tested and found to comply with the limits for Class A Information Technology
Equipment according to CISPR 32/EN 55032:2015 for Emissions and EN 55024:2010+A1:2015 for
Immunities.
Attention: This is a Class A product. In a domestic/residential environment this product may cause radio
interference in which the user may be required to take adequate measures.

Product specificaties

Merk: Apc
Categorie: Bewakingscamera
Model: NetBotz Camera Pod 165

Heb je hulp nodig?

Als je hulp nodig hebt met Apc NetBotz Camera Pod 165 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Bewakingscamera Apc

Apc

Apc NetBotz Camera Pod 160 Handleiding

6 Mei 2023
Apc

Apc NetBotz NBWL0355 Handleiding

23 April 2023
Apc

Apc NetBotz Room Monitor 355 Handleiding

9 April 2023
Apc

Apc NBWL0356A Handleiding

8 April 2023
Apc

Apc NetBotz Room Monitor 455 Handleiding

23 Maart 2023
Apc

Apc NetBotz Camera Pod 165 Handleiding

19 Februari 2023
Apc

Apc NetBotz NBPD0160A Handleiding

2 November 2022

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Aqara

Aqara Camera Hub G2H Handleiding

28 April 2024
Iiquu

Iiquu Dummy Dome Camera Handleiding

28 April 2024
Sony

Sony SNC-VB640 Handleiding

26 April 2024
Sony

Sony SNC-EB642R Handleiding

26 April 2024
Sony

Sony SNC-VB642D Handleiding

26 April 2024
Sony

Sony SRG-HD1 Handleiding

26 April 2024
Sony

Sony SNC-ZM550 Handleiding

26 April 2024
Sony

Sony SNC-EM642R Handleiding

26 April 2024
Sony

Sony SNC-EM641 Handleiding

26 April 2024
Sony

Sony SNC-ZB550 Handleiding

26 April 2024