AnD UA-611 Handleiding

AnD Bloeddrukmeter UA-611

Lees hieronder de 📖 handleiding in het Nederlandse voor AnD UA-611 (1 pagina's) in de categorie Bloeddrukmeter. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Unstable blood pressure due
to movement during
measurement.
Take another measurement.
Remain still during
measurement.
The systolic and diastolic
values are within 10 mmHg of
each other.
Apply the cuff correctly, and
take another measurement.
The pressure value did not
increase during the inflation.
The cuff is not applied
correctly.
PUL DISPLAY ERROR
The pulse is not detected
correctly.
Device internal error
Remove the batteries and
press the _START_ button, and
then install the batteries again.
If the error still appears, contact
the dealer.
Symbols printed on the device case.
Symbols Function / Meaning
Standby and Turn the device on.
SYS Systolic blood pressure in mmHg
DIA Diastolic blood pressure in mmHg
PUL/min. Pulse per minute
Battery installation guide
Direct current
Type BF: Device, cuff and tubing are designed to provide
special protection against electrical shocks.
EC directive medical device label
EU-representative
Manufacturer
Date of manufacture
WEEE label
SN Serial number
Refer to instruction manual/booklet
Polarity of DC jack
IP International protection symbol
6. Using the Monitor
6.1.
Installing / Changing The Batteries
1. Remove the battery cover.
2. Remove the used batteries from
the battery compartment in case
of changing them.
3. Insert new batteries into the
battery compartment as shown,
taking care that the polarities (+)
and (-) are correct.
4. Replace the battery cover. Use
only R6P, LR6 or AA batteries.
CAUTION
Insert the batteries as shown in the battery compartment. If installed
incorrectly, the device will not work.
When blinks on the display and the device announces that the
battery needs to be replaced, replace all batteries with new ones. Do
not mix old and new batteries. It may shorten the battery life, or cause
the device to malfunction. Replace the batteries two seconds or more
after the device turns off.
does not appear when the batteries are drained.
The battery life varies with the ambient temperature and may be shorter
at low temperatures.
Generally, four new R6P batteries will last approximately for three
months when used twice for measurement each day.
Use the specified batteries only. The batteries provided with the device
are for testing the device performance and may have a limited life.
Remove the batteries if the device is not to be used for a long time. The
batteries may leak and cause a malfunction.
6.2.
Connecting The Air Hose
Insert the air connector plug
into the air socket firmly.
6.3.
Connecting The AC Adapter
Insert the AC adapter plug into the DC
jack. Then, insert the AC adapter into
an electrical outlet. The AC adapter, the
model TB-233C is sold separately.
When disconnecting the AC
adapter from the electrical outlet,
grasp and pull the AC adapter body
out of the outlet.
When disconnecting the AC adapter plug from the blood pressure
monitor, grasp and pull the AC adapter plug out of the monitor.
6.4.
Selecting The Correct Cuff
Using the correct cuff size is important for an accurate reading. If the
cuff is not the proper size, the reading may yield an incorrect blood
pressure value.
The arm size is printed on each cuff.
The index and proper fit range, on the cuff, tell you if you are
applying the correct cuff. Refer to "6.5 Applying The Arm Cuff".
If the index points outside of the range, contact your local dealer to
purchase a replacement cuff.
The arm cuff is a consumable. If it becomes worn, purchase a new one.
Arm Size Recommended Cuff Size Catalog Number
31 cm to 45 cm Large adult cuff CUF-F-LA
22 cm to 32 cm Adult cuff CUF-F-A
Arm size: The circumference at the biceps.
Note: Models UA-611 and UA-651 are not designed for using a small
cuff.
Symbols printed on the cuff.
Symbols Function / Meaning Recommended Action
Artery Position Mark
Set the mark on
the artery of the upper
arm or in line with the
ring finger on the
inside of the arm.
Index
REF Catalog number
Proper fit range for the adult cuff. It's
printed on the adult cuff.
Over range printed on the adult cuff. Use the large adult cuff
instead of the adult cuff.
Proper fit range for the large adult cuff.
It's printed on the large adult cuff.
Under range printed on the adult cuff.
Under range printed on the large adult
cuff.
Use the adult cuff
instead of the large
adult cuff.
Lot number
Large adult cuff
Adult cuff
6.5.
Applying The Arm Cuff
1. Wrap the cuff around the upper arm, about 1 to 2 cm above the inside
of the elbow, as shown.
Place the cuff directly against the skin, as clothing may cause a faint
pulse and result in a measurement error.
2. Constriction of the upper arm, caused by rolling up a shirtsleeve, may
prevent accurate readings.
3. Confirm that the index points within the proper fit range.
Note: During measurement, it is normal for the cuff to feel very tight. (Do
not be alarmed).
7. Measurements
7.1.
Normal Measurement
1. Place the cuff on the arm at heart
level (preferably the left arm). Sit
quietly during measurement.
2. Press the _START_ button.
All of the display segments are
displayed. Zero is displayed
blinking briefly. Then the display
changes, as indicated in the
figure at the right, as the
measurement begins. The cuff
starts to inflate. It is normal for the
cuff to feel very tight. A pressure
bar indicator is displayed, as in
the figure at the right, during
inflation.
Note: If you wish to stop inflation at any time,
press the _START_ button again.
3. When inflation is complete,
deflation starts automatically and
the (heart mark) blinks,
indicating that the measurement
is in progress. Once the pulse is
detected, the mark blinks with
each pulse beat.
Note: If an appropriate pressure is not
obtained, the device starts to
inflate
again automatically.
4. When the measurement is
complete, the systolic and
diastolic pressure readings and
pulse rate are displayed. The cuff
exhausts the remaining air and
deflates completely.
5. Press the _START_ button again to turn off the power.
Note: Model UA-611 and UA-651 are provided with an automatic power
shut-off function. Allow at least 3 minutes between measurements on
the same person.
7.2.
Measurement with the Desired Systolic Pressure
If re-inflation occurs repeatedly,
use the following methods. If your
systolic pressure is expected to
exceed 230 mmHg, use this
procedure.
1. Place the cuff on the arm at heart
level (preferably the left arm).
2. Press the _START_ button.
3. During the zero blinks, press and
hold the _START_ button until a
number about 30 to 40 mmHg higher
than your expected systolic pressure
appears.
4. When the desired number is
reached, release the _START_ button
to start measurement. Then continue
to measure your blood pressure as
described on the section "7.1
Normal Measurement".
7.3.
Notes for Accurate Measurement
Sit comfortably on a chair. Rest your arm on the table. Do not cross
your legs. Keep your feet on the floor and straighten your back.
Sit down in a comfortable position. Place your arm on a table with your
palm facing upward and the cuff at the same level as your heart.
Place the center of the cuff at the same level as your heart.
Relax for about five to ten minutes before measurement. If you are
excited or depressed by emotional stress, the measurement will reflect
this stress as a higher (or lower) than normal blood pressure reading
and the pulse reading will usually be faster than normal.
Remain still and keep quiet during measurement.
Do not measure immediately after physical exercise or a bath. Rest for
twenty or thirty minutes before taking the measurement.
An individual's blood pressure varies constantly, depending on what
you are doing and what you have eaten. What you drink can have a
very strong and rapid effect on your blood pressure.
This device bases its measurements on the heartbeat. If you have a
very weak or irregular heartbeat, the device may have difficulty
determining your blood pressure.
Should the device detect a condition that is abnormal, it will stop the
measurement and display an error symbol. Refer to the section "5
Symbols" for the description of the symbols.
This device is intended for use by adults only. Consult with your
physician before using this device on a child. A child should not use this
device unattended.
Try to measure your blood pressure at the same time every day.
The automatic blood pressure monitor's performance may be affected by
excessive temperature or humidity, or altitude.
8. Recalling the Memory Data
The device automatically stores up to thirty blood pressure and pulse
measurements in memory. Data stored in memory are assigned a data
number in the order of the newest to the oldest. The oldest data displays as
"". The symbol in the upper left corner of the display indicates that
you are viewing previous data stored in memory.
8.1.
Recalling Data
1. When nothing is displayed, press
and hold the _START_ button to
recall the stored data.
2. Release the button when
displaying the average data.
3. The data number and stored data
are automatically displayed in
order from the last measurement.
4. The display will turn off
automatically after all data is
displayed.
Note: If you press the _START_ button
while recalling data, the device
turns off.
8.2.
Clearing Data
1. When turning off the device,
press and hold the _START_
button until the " " is
displayed.
2. Select " " to clear
data.
3. Data is cleared when the
mark blinks.
4. The device turns off
automatically.
9. What is an Irregular Heartbeat
The UA-611 and UA-651 provide a blood pressure and pulse rate
measurement even when an irregular heartbeat occurs. An
irregular heartbeat is defined as a heartbeat that varies by 25%
from the average of all heartbeats during the blood pressure
measurement. It is important that you are relaxed, remain still
and do not talk during measurements.
Note: We recommend contacting your physician if you see this
symbol frequently.
10. Pressure Bar Indicator
The indicator monitors the progress of pressure during
measurement.
11. About Blood Pressure
What is Blood Pressure?
Blood pressure is the force exerted by blood against the walls of
the arteries. Systolic pressure occurs when the heart contracts.
Diastolic pressure occurs when the heart expands. Blood
pressure is measured in millimeters of mercury (mmHg). One's
natural blood pressure is represented by the fundamental
pressure, which is measured first thing in the morning while one
is still at rest and before eating.
12. WHO Classification Indicator
Each segment of the bar indicator corresponds to the WHO blood
pressure classification.
: The indicator displays a
segment, based on the
current data,
corresponding to the
WHO classification.
13. Troubleshooting
Problem Possible Reason Recommended Action
Nothing
appears on
the display,
even when
the power is
turned on.
Batteries are
drained.
Replace all batteries with new
ones.
Battery terminals
are not in the
correct position.
Reinstall the batteries with
negative and positive terminals
matching those indicated on the
battery compartment.
The cuff
does not
inflate.
Battery voltage is
too low.
blinks. If the
batteries are
drained completely,
the mark does not
appear.
Replace all batteries with new
ones.
The device
does not
measure.
Readings
are too high
or too low.
The cuff is not
applied properly. Apply the cuff correctly.
You moved your
arm or body during
measurement.
Make sure you remain still and
quiet during measurement.
The cuff position is
not correct.
Sit comfortably and still. Place
your arm on a table with your
palm facing upward and the cuff
at the same level as your heart.
If you have a very weak or
irregular heartbeat, the device
may have difficulty in determining
your blood pressure.
Other
The value is
different from that
measured at a
clinic or doctor’s
office.
A
t a clinic or doctor's office, an
apprehension may cause an
elevated reading. Home
measurement reduces the effects
of outside influences on blood
pressure readings, supplements
the doctor's readings.
Remove the batteries. Place them
back properly and take another
measurement.
Note: If the actions described above do not solve the problem, contact
the dealer. Do not attempt to open or repair this product, as any
attempt to do so will make your warranty invalid.
14. Maintenance
Do not open the device. It uses delicate electrical components and
an intricate air unit that could be damaged. If you cannot fix the
problem using the troubleshooting instructions, contact the
authorized dealer in your area or our customer service department.
The A&D customer service will provide technical information, spare
parts and units to authorized dealers.
The device was designed and manufactured for a long service life.
However it is generally recommended to have the device inspected
every 2 years, to ensure proper functioning and accuracy. Please
contact the authorized dealer in your area or A&D for maintenance.
15. Technical Data
Type UA-611 , UA-651
Measurement method Oscillometric measurement
Measurement range Pressure: 0 - 299 mmHg
Systolic pressure: 60 - 279 mmHg
Diastolic pressure: 40 - 200 mmHg
Pulse: 40 - 180 beats / minute
Measurement accuracy Pressure: ±3 mmHg
Pulse: ±5 %
Power supply 4 x 1.5V batteries (R6P, LR6 or AA)
Optional AC adapter (TB-233C) (Not included)
Number of measurements
Approx. 700 times LR6 (
alkaline batteries
)
Approx. 200 times R6P (
manganese batteries
)
With pressure value 180 mmHg, room
temperature 23 °C.
Classification Internally powered ME equipment
Continuous operation mode
Clinical test According to ANSI / AAMI SP-10 1992
EMC IEC 60601-1-2: 2007
Memory Last 30 measurements
Operating conditions +10°C to +40 °C / 15 %RH to 85 %RH / 800 hPa
to 1060 hPa
Transport / Storage conditions -20 °C to +60 °C / 10 %RH to 95 %RH
700hPa to 1060hPa
Dimensions Approx. 96 [W] x 68 [H] x 130 [D] mm
Weight Approx. 230 g, excluding the batteries
Applied part Cuff Type BF
Useful life Device: 5 years (
when used six times a day
)
Cuff: 2 years (
when used six times a day
)
AC adapter:5 years (
when used six times a day
)
Accessory AC adapter/TB233C
The adapter is to connect the device to a
power source at home. Please contact your
local A&D dealer for purchasing. The AC
adapter is required to be inspected or
replaced periodically.
Symbols that are printed on the AC adapter.
Symbols Function / Meaning
For indoor use only
Class II device
Thermal fuse
Fuse
EC directive device label
EAC certification device label
Polarity of AC adapter plug
Accessories sold separately
Cuff Catalog Number Cuff Size Arm Size
CUF-F-LA Large adult cuff 31 cm to 45 cm
CUF-F-A Adult cuff 22 cm to 32 cm
Arm size: The circumference at the biceps.
AC Adapter Catalog Number Plug (Outlet type)
TB-233C Type C
Note: Specifications are subject to change without prior notice.
A&D Company, Limited
1-243 Asahi, Kitamoto-shi, Saitama 364-8585 JAPAN
Telephone: [81] (48) 593-1111 Fax: [81] (48) 593-1119
A&D INSTRUMENTS LIMITED
Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire
OX14 1DY United Kingdom
Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485
A&D ENGINEERING, INC.
1756 Automation Parkway, San Jose, California 95131 U.S.A.
Telephone: [1] (408) 263-5333 Fax: [1] (408)263-0119
A&D Australasia Pty Ltd.
32 Dew Street, Thebarton, South Australia 5031 AUSTRALIA
Telephone: [61] (8) 8301-8100 Fax: [61] (8) 8352-7409
Digital Blood Pressure Monitor
Model UA-611 / UA-651
Instruction Manual Original
1WMPD4002762E
1. Dear Customers
The A&D blood pressure monitor is one of the most advanced
monitors available and is designed for ease of use and accuracy.
This device will facilitate your daily blood pressure regimen.
We recommend that you read through this manual carefully before
using the device for the first time.
2. Preliminary Remarks
This device conforms to the European Directive 93/42 EEC for
Medical Products. This is made evident by the mark of
conformity. (0123: The reference number to the involved notified
body)
The device is designed for use on adults only, not newborns or
infants.
Environment for use. The device is for use in the home healthcare
environment.
This device is designed to measure blood pressure and pulse rate
of people for diagnosis.
3. Precautions
Precision components are used in the construction of this device.
Extremes in temperature, humidity, direct sunlight, shock or dust
should be avoided.
Clean the device and cuff with a dry, soft cloth or a cloth dampened with
water and a neutral detergent. Never use alcohol, benzene, thinner or
other harsh chemicals to clean the device or cuff.
Avoid tightly folding the cuff or storing the hose tightly twisted for
long periods, as such treatment may shorten the life of the
components.
Take care to avoid accidental strangulation of babies or infants
with the hose.
Do not twist the air hose during measurement. This may cause
injury due to continuous cuff pressure.
The device and cuff are not water resistant. Prevent rain, sweat
and water from soiling the device and cuff.
Measurements may be distorted if the device is used close to
televisions, microwave ovens, X-ray or other devices with strong
electrical fields.
Wireless communication devices, such as home networking
devices, mobile phones, cordless phones and their base stations,
walkie-talkies can affect this blood pressure monitor.
Therefore, a minimum distance of 11 feet should be kept from
such devices.
When reusing the device, confirm that the device is clean.
Used equipment, parts and batteries are not treated as ordinary
household waste, and must be disposed of according to the
applicable local regulations.
Do not modify the device. It may cause accidents or damage to
the device.
To measure blood pressure, the arm must be squeezed by the
cuff hard enough to temporarily stop blood flow through the
artery. This may cause pain, numbness or a temporary red mark
to the arm. This condition will appear especially when
measurement is repeated successively. Any pain, numbness, or
red marks will disappear with time.
Measuring blood pressure too frequently may cause harm due to
blood flow interference. Check that the operation of the device
does not result in prolonged impairment of blood circulation,
when using the device repeatedly.
Clinical testing has not been conducted on pregnant women. Do
not use the device on pregnant women.
If you have had a mastectomy, please consult a doctor before
using the device.
Do not let children use the device by themselves and do not
leave the device within the reach of children.
There are small parts that may cause a choking hazard if
swallowed by mistake by infants.
Do not touch the batteries, the patient and the DC jack at the
same time. That may result in electrical shock.
Contraindications
The following are precautions for proper use of the device.
Do not apply the cuff on an arm with another medical electrical
equipment attached. The equipment may not function properly.
People who have a severe circulatory deficit in the arm must
consult a doctor before using the device, to avoid medical
problems.
Do not self-diagnose the measurement results and start
treatment by yourself. Always consult your doctor for evaluation
of the results and treatment.
Do not apply the cuff on an arm with an unhealed wound.
Do not apply the cuff on an arm receiving an intravenous drip or
blood transfusion. It may cause injury or accidents.
Do not use the device where flammable gases such as
anesthetic gases are present. It may cause an explosion.
Do not use the device in highly concentrated oxygen
environments, such as a high-pressure oxygen chamber or an
oxygen tent. It may cause a fire or explosion.
4. Parts Identification
Display
5. Symbols
Symbols that appear on the display
Symbols Function / Meaning Recommended Action
A
ppears while measurement
is in progress. It blinks when
the pulse is detected.
Measurement is in
progress. Remain as still
as possible.
I.H.B. appears when an
irregular heartbeat is detected.
It may light when a very slight
vibration like shivering or
shaking is detected.
Previous measurements
stored in memory.
FULL BATTERY
The battery power indicator
during measurement.
LOW BATTERY
The battery power is low when
it blinks.
Replace all batteries with
new ones when the mark
blinks.
A
ir Socke
t
Air Connector Plug
A
ir Hose
Proper fit range
Measurement in progres
s
Inflation complete
Inflation in progres
s
Cuff
1 to 2 cm
Artery position mark
Secure the fabric fastener
Air hose
Index and Proper fit range
At heart level
Refer to the section
"7.1 Normal Measurement"
Press the _START_ button
The desired pressure
Inflation in progress
Press and hold the
_START_ button
Release the _START_
button to stop inflation
Press and hold the
_START_ button
The mark blinks.
Data is cleared.
Release the
button
Select " " to
clear data.
Turns off automatically
5 seconds
Step 1
Step 3
Step 4
Step 2
Press and hold the
_START_ button
Release the button
mark
Average data
Data number
Stored Data
To next data
Turns off automatically
No data
WHO Classification Indicator
Severe hypertension
Moderate hypertension
Mild hypertension
High normal
Normal
Optimal
Exhausts remaining air
automatically
At heart level
Press the _START_ button
All of the display segments
Zero display
Starts inflation
Pressurizing
Measurement in progress
Systolic pressure
Diastolic pressure
WHO classification
Pulse rate
Turn off with the
_START_ button
Pressurizing Releasing air
Display
Air Hose
Arm Cuff
START
Button
Index
Air Socket
Proper fit range
Artery position mark
A
ir Connector Plug
Battery Compartment
Battery Cove
MEMORY
Systolic Pressure
Diastolic Pressure
Pulse Rate
Heart Mark
Battery Indicator
I.H.B. symbol
(Irregular Heartbeat symbol)
Pressure Bar Indicator and
WHO Classification Indicator
Note: Model UA-611 doesn't have the DC jack for AC adapter.
The DC jack is located on the rear of the model,UA-651 only. The
AC adapter is an optional accessory.(sold separately)
Model UA-651 only
DC jack
AC adapter plug
AC adapter Plug
DC
j
ack
Model UA-651 only
Do not roll up shirtsleeve tightly

Product specificaties

Merk: AnD
Categorie: Bloeddrukmeter
Model: UA-611

Heb je hulp nodig?

Als je hulp nodig hebt met AnD UA-611 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Bloeddrukmeter AnD

AnD

AnD UA-767F Handleiding

11 September 2022
AnD

AnD UB-510 Handleiding

11 September 2022
AnD

AnD UA-651 BLE Handleiding

11 September 2022
AnD

AnD UA-621 Handleiding

11 September 2022
AnD

AnD UB-542 Handleiding

11 September 2022
AnD

AnD UM-201 Handleiding

11 September 2022
AnD

AnD UA-651 Handleiding

11 September 2022
AnD

AnD UA-767S-W Handleiding

11 September 2022
AnD

AnD UA-611 Handleiding

11 September 2022
AnD

AnD UA-853 Handleiding

11 September 2022

Handleiding Bloeddrukmeter

Nieuwste handleidingen voor Bloeddrukmeter

Dr. Senst

Dr. Senst BP118A Handleiding

25 April 2024
Scala

Scala SC 6750A Handleiding

6 April 2024
Scala

Scala SC 7400 NFC Handleiding

6 April 2024
Rossmax

Rossmax X3 BT Handleiding

27 Maart 2024
Rossmax

Rossmax X9 BT Handleiding

27 Maart 2024
Boso

Boso Clinicus I Handleiding

27 Maart 2024
Boso

Boso Roid II Handleiding

27 Maart 2024
Rossmax

Rossmax CalPro Handleiding

27 Maart 2024
IHealth

IHealth View BP7S Handleiding

27 Maart 2024
Boso

Boso Varius Handleiding

27 Maart 2024