AMX MXA-UENET Handleiding

AMX Kabels voor pc's en randapparatuur MXA-UENET

Lees hieronder de 📖 handleiding in het Nederlandse voor AMX MXA-UENET (2 pagina's) in de categorie Kabels voor pc's en randapparatuur. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Installation Guide

MXA-UENET Video Acceleration Cable

Overview

The MXA-UENET Video Acceleration accessory cable ( ) plugs into a USB port of FG5968-75

the Modero X Series® Touch Panel and routes Ethernet traffic into the Modero X Series USB

subsystem, which has been optimized to further accelerate streaming video performance

(FIG. 1).

Within the Modero X Series touch panels, streaming video is optimized via the use of the

MXA-MPL Multi Preview Live (FG5968-10). If using an MXA-MPL is not an option, the

MXA-UENET video acceleration cable may be used to connect streaming video feeds to the

MXT/D-1000 and MXT/D-700 touch panels.

Specifications

Installation for Tabletop Touch Panels

To connect your MXT-1000 or MXT-700 tabletop touch panel to the network via the MXA-

UENET:

1. On a soft surface, turn the touch panel face-down to access the bottom of the device.

2. Remove the clamp holding the Ethernet cable (FIG. 2) until the Ethernet cable moves

freely.

3. Remove the Ethernet cable connector and pull the cable out of the clamp. Discard this

cable.

4. Press the Ethernet connector cable on the MXA-UENET (FIG. 1) into the clamp. Do

NOT tighten the clamp at this time.

5. Using a nonconductive item such as a wooden stick, insert the Ethernet cable

connector into the device. Use the stick to ensure that the connector is properly

seated.

6. Tighten the clamp to secure the Ethernet cable. Make sure the clamp is around the

bundled black cable, not the individual wires.

7. Insert the USB connector into one of the USB ports on the rear of the touch panel.

8. Connect the RJ45 connector to its incoming Ethernet cable.

9. Turn the touch panel upright and apply power.

NOTE: For more information on installing your touch panel, please refer to the MXT/D-1000

Operation Reference Guide or the MXT/D-700 Operation Reference Guide, available at

www.amx.com.

Installation for Wall/Flush Mount Touch Panels

To connect your MXD-1000 or MXD-700 wall/flush mount touch panel to the network via the

MXA-UENET:

NOTE: If the touch panel has already been installed in the wall or mounting surface, the

touch panel and the back box must be removed from the mounting surface to install the

MXA-UENET. Thread the connecting CAT5 Ethernet cable through the back box hole before

installing the MXA-UENET. In new installations, separate the back box from the touch panel,

as the back box must have the MXA-UENET threaded through it before the touch panel can

be installed.

NOTE: In solid-wall installations, make sure to have clearance within the wall for the Ethernet

port jack and the excess cable before starting the installation.

1. The USB connector on the MXA-UENET must be connected to the USB port on the

top of the touch panel (one on the MXD-1000 and two on the MXD-700). To facilitate

this, when looking at the front of the back box as it installs into the wall, remove the top

left knockout in the back box (FIG. 3).

2. Thread the MXA-UENET through the knockout hole, and install the back box into the

wall or mounting surface (FIG. 4). Lock down the back box using the back box’s

locking tabs for drywall installations or with screws (not included) for solid-wall or

rough-in box installations.

FIG. 1 MXA-UENET

MXA-UENET (FG5968-75) Specifications

Length: 6.10 ft (1.86 m)

Weight: 0.25 lbs (113.40 g)

Included Accessories: MXA-UENET Installation Guide (93-5968-75)

Other AMX Equipment: • MXT-1000 10.1" Modero X® Series Tabletop Touch Panel

( )FG5968-03

• MXT-700 7" Modero X® Series Tabletop Touch Panel

( )FG5968-04

• MXD-1000-L 10.1" Modero X® Series Wall/Flush Mount

Touch Panel, Landscape (FG5968-13)

• MXD-1000-P 10.1" Modero X® Series Wall/Flush Mount

Touch Panel, Portrait (FG5968-07)

• MXD-700-L 7" Modero X® Series Wall/Flush Mount Touch

Panel, Landscape (FG5968-14)

• MXD-700-P 7" Modero X® Series Wall/Flush Mount Touch

Panel, Portrait (FG5968-08)

FIG. 2 Touch panel bottom, displaying the Ethernet cable.

Ethernet USB

Connector

Port

Ethernet

Connector

Ethernet Cable

Connector

Clamp

MXT-1000

FIG. 3 Rear of MXD-700 touch panel, showing back box

FIG. 4 Installation of the MXA-UENET into an MXD-700 back box

Touch panel Back box

Top

Entry knockout for

MXA-UENET

connector

MXA-UENET

Backside

of wall USB connector

cable

Ethernet connector

cable

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

3/13

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-5968-75 REV: A

3. In order to install the Ethernet connector, the current touch panel connector must be

removed and the MXA-UENET connector installed in its place. Carefully unplug the

touch panel’s connector from its port. With the touch screen facing you, the connector

is located to the right of the Micro-USB port (FIG. 5) on both the MXD-1000 and the

MXD-700.

4. Using a nonconductive item such as a wooden stick, insert the MXA-UENET’s

Ethernet cable connector into the touch panel. Use the stick to ensure that the

connector is properly seated. Leave the panel’s original connector within the device;

do NOT remove it.

5. With the touch panel still outside of the back box, insert the USB connector into the

touch panel’s USB port (FIG. 5).

6. Carefully install the touch panel into the back box, hooking the panel at the top of the

back box. Make sure that the cords for the USB and Ethernet connectors pass through

the knockout holes in the top of the back box without interference.

7. Connect the Ethernet port on the MXA-UENET (FIG. 1) to the network via CAT5

Ethernet cable and apply power.

NOTE: For more information on installing your touch panel, please refer to the MXT/D-1000

Operation Reference Guide MXT/D-700 Operation Reference Guide or the , available at

www.amx.com.

Configuring the Touch Panel to Receive the Video

Stream

To receive streaming video from a network source:

1. In the touch panel’s Settings Pages, select Conﬁguration > Advanced Conﬁg >

Streaming Video, entering the touch panel’s password if necessary.

2. From the Streaming Video page, select Enter URL to open the keyboard.Set URL

3. Enter the URL for the video stream and click OK.

NOTE: For more information on configuring your touch panel for streaming video, please

refer to the Modero X Series Programming Guide, available at www.amx.com.

FIG. 5 MXD-1000 touch panel connections

Ethernet Port

and connector

USB Port

and connector

Micro-USB

port

MXD-1000

touch panel

connector

Product specificaties

Merk:	AMX
Categorie:	Kabels voor pc's en randapparatuur
Model:	MXA-UENET
Kleur van het product:	Zwart
Gewicht:	113.4 g
Snoerlengte:	1.86 m
Aansluiting 1 type:	Mannelijk
Aansluiting 2 type:	Mannelijk