AmpliVox Beltblaster S206 Handleiding
AmpliVox
Niet gecategoriseerd
Beltblaster S206
Lees hieronder de 📖 handleiding in het Nederlandse voor AmpliVox Beltblaster S206 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 7 personen en werd door 4 gebruikers gemiddeld met 4.4 sterren beoordeeld
Pagina 1/2
AmpliVox 650 Anthony Trail Suite D, Northbrook, IL 60062 Phone: (800)267-• • 5486 • Fax: (800)267-5489 www.ampli.com
S206 BELT BLASTER /
S207 BELT BLASTER PRO
WAISTBAND AMPLIFIER
INCLUDED:
1. Belt Blaster Pro Personal Waistband Amplifier
2. 44″ Adjustable Belt
3. Headset and Lapel Microphone
4. AC Adapter/Recharger
5. Storage Case
6. Waistband Case
7. 6 - NiMH rechargeable batteries
S206 Batteries: Insert six (6) standard ʺAAʺ batteries (not included) as show below.
Install Batteries:
1. Locate the battery compartment on the right rear side of the amplifier.
2. Press (do not pry) the cover locking tab to the right and lift to remove battery cover.
3. Install the 6 batteries . Follow the picture of battery direction as seen in the bottom of
the holder. Negative ( ) flat side of battery toward spring. -
4. Insert battery cover and press back into place.
BATTERY REPLACEMENT
When batteries will no longer hold a charge, all 6 batteries be replaced at the same (S207) MUST
time. Mixing old and new batteries can lead to battery failure.
CHARGING BATTERIES FOR FIRST USE (S207)
Your new Belt Blaster Pro is shipped with 6 NiMH rechargeable batteries. Once they have been installed,
they must receive a deep charge (24 hours) before being used.
1. Insert battery charger mini plug (AC adapter) into the charging port located on the bottom of the amplifier.
2. Plug the adapter into a working power outlet. Charge the Belt Blaster Pro for 24 hours for the first charge.
After this, only 8 14 hour charge is necessary-
.
S207 Rechargeable Batteries: S207 The rechargeable Nickel Metal Hydride batteries of the Belt Blaster Pro will have a life
expectancy of approximately 2 years. Actual life will vary significantly depending on your usage and charging habits. There may
be a time when you need to use backup power to get through a presentation. The Belt Blaster PRO was intentionally designed
to accommodate standard batteries for just such occasions.″AA″
NOTE:
The AC Adapter/Charger can be used to recharge the batteries . Can not power the amplifier simultaneously.ONLY
CAUTION! NEVER PLUG IN AC ADAPTER/CHARGER WITH NON RECHARGEABLE BATTERIES INSIDE AMPLIFIER. -
SERIOUS DAMAGE MAY BE CAUSED TO BATTERIES AND AMPLIFIER.
1. Belt Blaster Personal Waistband Amplifier
2. 44″ Adjustable Belt
3. Headset and Lapel Microphone
4. Storage Case
INCLUDED:
S206 S207
INSERTING/CHANGING THE BATTERIES
CHARGER PORT
AmpliVox 650 Anthony Trail Suite D, Northbrook, IL 60062 Phone: (800)267-• • 5486 • Fax: (800)267-5489 www.ampli.com
OPERATING INSTRUCTIONS
The amplifier is usually worn on the front of the waist, much
like a waist pack The woven nylon waist band is adjusta-“ ” .
ble to 44 inches. Remember to wear the Belt Blaster so the
speaker grill faces out away from the body to avoid feed-
back.
1. With the amplifier turned , insert the 3.5mm lapel/OFF
headset microphone plug into the jack on top of the
amplifier.
2. Put the amplifier on your waist, adjust the attached belt
to fit, then clip the buckle. Please take note of the path
of the nylon belt through the clips. In the event that the
belt is disassembled, it is imperative that the belt be
correctly reinstalled.
3. Turn the amplifier by turning the volume control ON
knob to the 11 o clock position while speaking at a con-’
sistent volume level.
4. When you perceive your voice is loud enough, reduce
the volume slightly. This is done because you are
standing behind the speaker and your voice is consider-
ably louder then you perceive.
USB THUMB DRIVE
1. Insert USB Thumb Drive into the USB Slot on top of
amplifier.
2. Press ON/OFF/Play button to turn on the USB. USB
power LED will light up and flash. Press button again to
play first recorded item.
3. Press to advance to next song/message or hold for 2
seconds to fast forward.
4. Press to go back to last song/message or hold for 2
seconds to fast backwards.
TROUBLE SHOOTING
POPPING OR CRACKLING NOISE
Popping or crackling noises coming from the speaker of your Belt Blaster, particularly when the microphone cable is moved, are
usually caused by dirt, finger oils or corrosion build up on the microphone plug.-
Remove the plug and clean the metal tip and sleeve with a clean cloth or cotton swab moistened with alcohol, or with a pre-
moistened towelette (Wet Wipe or similar). If none of these are available, use a clean, dry cloth or paper towel. While not as
effective, this should still improve the contact.
ON/OFF
VOLUME
POWER/BATTERY
LOW LED
MICROPHONE
JACK
Nov, 2020
TOP
USB
SLOT
USB
ON/OFF/
PLAY
USB
FF/FB
USB
PWR LED
Product specificaties
| Merk: | AmpliVox |
| Categorie: | Niet gecategoriseerd |
| Model: | Beltblaster S206 |
Heb je hulp nodig?
Als je hulp nodig hebt met AmpliVox Beltblaster S206 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd AmpliVox
12 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
Handleiding Niet gecategoriseerd
- Niet gecategoriseerd Ziggo
- Niet gecategoriseerd Conair
- Niet gecategoriseerd Artrom
- Niet gecategoriseerd Galcon
- Niet gecategoriseerd Kora
- Niet gecategoriseerd Yamaha
- Niet gecategoriseerd Lagrange
- Niet gecategoriseerd Reflexion
- Niet gecategoriseerd Electronics International
- Niet gecategoriseerd Pro-User
- Niet gecategoriseerd Scytek
- Niet gecategoriseerd Badiona
- Niet gecategoriseerd Whirlpool
- Niet gecategoriseerd Lepu Medical
- Niet gecategoriseerd ISA
Nieuwste handleidingen voor Niet gecategoriseerd
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025