Aluratek ATLTSAF Handleiding

Aluratek Niet gecategoriseerd ATLTSAF

Lees hieronder de 📖 handleiding in het Nederlandse voor Aluratek ATLTSAF (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 98 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

Hook

Sensor

Charging Port

LED

Water

Resistant

Ring Blue ght ashli ﬂ

Wai ng for Blue �

light to touch

Blue ght ashli ﬂ

6 sec

Red and blue

light ashﬂ

Wai ng for Blue �

light to touch

Red and blue ght li ﬂash Blue ght for 4 secli

Wai ng for Blue �

light to touch

Wai ng for Red �

light to t chou

Blue ght for 2 secli

6 sec

Wai ng for Blue �

light to touch

*Refer to Fingerprint

Registra�on Sec on�

Red and blue ght li

ﬂash

Activation

Press hook to activate the lock:

Note:

If the LED light is not activated,

please charge the lock using

the included micro-USB cable.

If no action is proceeded within

15 seconds after the lock is

activated, the power will be

turned off automatically.

Caution: Please set up your personalized Fast-Click Code after first fingerprint

registration IMMEDIATELY.

Fast-Click allows you to create a custom access code of short and long taps to manually

un-lock the lock without a computer. The Fast-Click code is a 6-digit code made up of a

string of 6 long and short taps.

Code Registration :

1.1 To enter the code registration mode:

- Tap and hold the hook for 5 seconds and wait for a flashing blue light, continue

holding until the red and blue light flashes.

1.2 Input your first Fast-Click digit:

- A long tap using the hook longer than 1 seconds, red and blue light turns on and

that indicates a successful registration of a long tap.

- A short tap is less than 1 second, LED change to a rapid flashing blue light,

indicates a successful registration of a short tap.

1.3 The red and blue light will flash rapidly after each successful registration.

1.4 Repeat step 2 until all 6 digits are successfully enrolled. After a code has been

successfully registered, a blue light will be activated and stay on for 4 seconds.

* Please write down your code after registration: __ __ __ __ __ __

Unlock Using Fast-Click Code or Change Your Code:

To Unlock:

2.1 Tap and hold the hook for 5 seconds and wait for a flashing blue light, continue

holding until the red and blue light flashes slowly.

2.2 Enter your registered code and wait until the blue light activates, that indicates the

code is entered correctly. The lock will be unlocked after 3 seconds.

2.3 If the code is entered incorrectly, a red light will be activated and turns into a slow

flashing red and blue light right after, then you can re-enter your registered

Fast-Click code.

* The lock will exit the Fast-Click Unlock Mode after 4 attempts of entering the wrong

code.

TouchLock Unlock Fingerprint Registration

Registration of Additional Fingerprints Erase Fingerprint Records

-In the unlikely event the battery dies while locked, TouchLock should be charged using

an external battery to provide quick access to un-lock, such as a Power Bank.

-Low battery warning: the red light will flash 3 times when the battery has 30% charge

left, it will flash continuously when it has 10% charge left

-Tip: try registering multiple fingers. Smaller profile fingers tend to work best.

FAQ

Aluratek warrants this product against defect in material or workmanship for 1 YEAR

from the date of purchase.

This warranty becomes invalid if the factory-supplied serial number or "warranty void" sticker has

been removed or altered on the product.

This warranty does not cover:

A) Cosmetic damage or damage due to acts of God

B) Accident, misuse, abuse, negligence or modification of any part of the product.

C) Damage due to improper operation or maintenance, connection to improper equipment,

or attempted repair by anyone other than Aluratek.

D) Products sold AS IS or WITH FAULTS.

IN NO EVENT SHALL ALURATEK'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT

FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

RESULTING FROM THE USE OF THE PRODUCT, IT'S ACCOMPANYING SOFTWARE, OR

IT'S DOCUMENTATION.

Aluratek makes no warranty or representation, expressed, implied, or statutory, with respect to it's

products, contents or use of this documentation and all accompanying software, and specifically

disclaims it's quality, performance, merchantability, or fitness for any particular purpose. Aluratek

reserves the right to revise or update it's product, software or documentation without obligation to

notify any individual or entity.

Warranty

aluratek.com

model ATLTSAF

Quick Start Guide

All Weather Keyless Fingerprint Lock

Technical Support

If you need further assistance, please contact the Aluratek support department for

troubleshooting prior to returning this device.

E-mail: support@aluratek.com

Web: www.aluratek.com/helpdesk

Local (Irvine, CA): 714-586-8730

Toll free: 1-866-580-1978

TouchLock is a smart padlock. There is no need for keys or combinations. The lock can

store up to 20 fingerprints which easily allows you to share your lock with your family and

friends. Our TouchLock TSA also comes with a waterproof rubber ring which allows the

locks to be used outdoors.

Reset the Lock Using PC Tool

3.1 Repeat the previous step 2.1,2.2 and tap the hook within 3 seconds after the blue light

is activated, then a rapid red blue light will flash, indicates a new code can be

enrolled. (The previous registered code will be erased automatically)

3.2 Repeat step 1.2,1.3 and 1.4 in Code Registration section to input your new

Fast-Click Code.

Erase the Fast-Click Code

-When clear all fingerprint record, Fast-Click code record would also be erased, method

please refer to erase fingerprint record section in this manual

Change or Erase Your Fast-Click Unlock Code

Press the hook once and

wait for the flashing blue

light.

Place your registered

finger on the touch sensor

and hold until you see the

solid

blue light

*If a red light flashes,

please place your finger on

the sensor and try again.

TouchLock will then unlock

once the registry is

confirmed.

*Finger recognition may

require multiple attempts

due to your placement of

the finger on the touch

sensor.

Press the hook once,

wait for the flashing red

and blue light;

Put your finger on the

sensor and wait for the

solid blue light

*If a red light flashes,

please put flatter part of

your finger on the sensor

and try again.

Repeat step 2 for three

times until you see a solid

blue light flashing for 4

seconds, indicating the

successful enrollment of

the fingerprint.

1. Press and hold hook

until you see the rapid

flashing blue light. Use a

previously registered

finger to authenticate.

After successful

authentication, the light will

change to a solid blue light

for a few seconds. If a red

light appears, lift finger

and retry. Immediately

following the solid blue

light, wait for the flashing

red and blue light.

2. Put your finger on the

sensor and wait for the

solid blue light

*If a red light flashes,

please put flatter part of

your finger on the sensor

and try again.

3. Repeat step 2 for three

times until you see a solid

blue light flashing for 4

seconds, indicating the

successful enrollment of

the fingerprint.

Press the hook for 6

seconds until you see the

rapid flashing blue light

Touch sensor with the

previously enrolled finger

until you see the solid blue

light.

*If a red light flashes,

please put your finger on

the sensor and try again.

Press the button again for

6 seconds when you see

the rapid flashing red and

blue light, then release the

button when you see the

rapid flashing red light.

Touch sensor with the

previously enrolled finger

again and wait for the

solid blue light flashes for

2 seconds.

All the enrolled fingerprints

are successfully erased.

Reset the Lock Using The TouchLock PC Tool (PC only)

1. Go to the following URL:

https://www.aluratek.com/bio-key-touchlock-tsa-all-weater-bio-lock-fingerprint-recognition/

2. Find the Downloads section on the product page and click the link "TouchLock_PC

Tool" to download the tool

3. Connect the lock to your computer's USB port via the included USB cable

4. Open the "TouchLock PC Tool" ZIP folder and click on the tool

5. Select "Unlock by Password" buttonas shown below:

*Note: The default password is “0000”

To erase all enrolled fingerprint records:

-Click on the “Delete Fingerprints”

-Click “yes” and enter 4 digit password.

-Then click “Confirm”.

Change the password:

1. Click on “change

password”

2. Enter the current 4 digit

password

3. Enter and confirm the new

4 digit password

Fast-Click Unlock Mode

Product specificaties

Merk:	Aluratek
Categorie:	Niet gecategoriseerd
Model:	ATLTSAF

Heb je hulp nodig?

Als je hulp nodig hebt met Aluratek ATLTSAF stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Aluratek

Aluratek AUH100F Handleiding

8 April 2024

Aluratek AWCPA01FB Handleiding

19 Maart 2024

Aluratek AULS03F Handleiding

19 Maart 2024

Aluratek AUH200F Handleiding

28 Augustus 2023

Aluratek AWAGA01F Handleiding

28 Augustus 2023

Aluratek AUPS01F Handleiding

28 Augustus 2023

Aluratek AUM01F Handleiding

27 Augustus 2023

Aluratek APAP01F Handleiding

25 Augustus 2023

Aluratek AWLMC01F Handleiding

6 Juli 2023

Aluratek ABPM02F Handleiding

1 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024

Sony PDW-U4 Handleiding

26 April 2024

Sony NXL-FR318 Handleiding

26 April 2024