Alto Professional Stealth Wireless Handleiding
Alto Professional
Draadloos audio systeem
Stealth Wireless
Lees hieronder de đź“– handleiding in het Nederlandse voor Alto Professional Stealth Wireless (40 pagina's) in de categorie Draadloos audio systeem. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/40
User Guide
English ( 3 – 8 )
GuĂa del usuario
Español ( 9 – 14 )
Guide d'utilisation
Français ( 15 – 20 )
Guida per l'uso
Italiano ( 21 – 26 )
Benutzerhandbuch
Deutsch ( 27 – 32 )
Gebruikershandleiding
Nederlands ( 33 – 38 )
Appendix
English ( 39 )
2
User Guide (English)
Introduction
Thank you for purchasing the Alto Professional Stealth Wireless system. Stealth Wireless is a
convenient way to carry an audio signal from the main mixing and listening location to your powered
loudspeakers. Compatible with any active loudspeaker, this system can be used to simplify a new
installation or to retrofit an existing sound system. Welcome to the sound of wireless freedom.
Features:
• Wireless audio connectivity to active loudspeakers
• Replaces up to 200' of console-to-system cabling
• No compromise in audio quality
• Reliable UHF band; 16 selectable channels
• Adjustable squelch eliminates interference
• Dual-channel transmitter: two XLR-1/4" combo inputs
• Single-channel receivers: XLR output
• Grow your system using the Stealth Expander Pack (sold separately)
Box Contents
• Stealth Wireless Transmitter (x1)
• Stealth Wireless Receiver (x2)
• Hook and Loop Strips (for receivers)
• M10 Screws (x2)
• Machine Screws (x2)
• Power Adapters (x3)
• User Guide
• Safety & Warranty Manual
Support
For complete system requirements, compatibility information, and product registration, visit the Alto
Professional website: altoprofessional.com.
For additional product support, visit altoprofessional.com/support.
Important
CAUTION! Permanent hearing loss may be caused by exposure to extremely high noise levels. The
U.S. Government's Occupational Safety and Health Administration (OSHA) has specified permissible
exposures to certain noise levels.
According to OSHA, exposure to high sound pressure levels (SPL) in excess of these limits may result
in hearing loss. When using equipment capable of generating high SPL, use hearing protection while
such equipment is under operation. The table below defines exposure for a given duration.
HOURS PER DAY SPL EXAMPLE
8 90 Small gig
6 92 Train
4 95 Subway train
3 97 High level desktop monitors
2 100 Classical music concert
1.5 102 Riveting machine
1 105 Machine factory
.50 110 Airport
.25 or less 115 Rock concert
3
Transmitter Features
Rear Panel
1. Antennas – Place the antennas in a vertical position for best
results in transmitting the wireless signal. If the wireless signal
quality is poor, change the position of the antennas.
2. Combo Inputs – Connect balanced or unbalanced 1/4” or XLR
line-level sources here.
3. Power Connector – Connect the included 12V DC, 300 mA power
adapter here.
Front Panel
1. Power Button – Press this button to turn the
transmitter on/off.
2. Mono/Stereo Select – Adjust this switch to
change the wireless signal that is sent to the
receiver to be either mono/stereo.
3. Signal Clip Indicator – The LED will turn red when the signal is close to peaking (clipping).
Note: The LED will begin to flicker red at -4 dB before clipping and become solid red if clipping
occurs.
4. Channel Select – Adjusts the frequency band range.
• Match channels on the transmitter and receiver in order to get a signal.
• Watch the receiver’s AF indicator and RF indicator to make sure a signal is being received.
• If you receive interference, change to another channel until a clean signal comes through.
• To change the channel:
a. Press and hold the Channel Select button for approximately 1 second until the
channel number flashes.
b. While the channel number is flashing, tap the Channel Select button to cycle through
the 16 available channels. Set the transmitter and receiver(s) to the same channel.
c. When the desired channel number is shown, wait for 3 seconds. When the channel
number stops flashing, that channel is now selected.
d. Use the Left/Right Selector switches to set which receiver receives the left and right
signals, since the left and right signals are sent on the same channel.
5. Trim – Adjusts the signal level.
POWER MONO/ STEREO
LR
MIN MAX MIN MAX
CHANNEL
1
2
3
4
55
1
1
2 2 3
Product specificaties
| Merk: | Alto Professional |
| Categorie: | Draadloos audio systeem |
| Model: | Stealth Wireless |
Heb je hulp nodig?
Als je hulp nodig hebt met Alto Professional Stealth Wireless stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Draadloos audio systeem Alto Professional
7 September 2022
Handleiding Draadloos audio systeem
- Draadloos audio systeem Sony
- Draadloos audio systeem Samsung
- Draadloos audio systeem JBL
- Draadloos audio systeem Pioneer
- Draadloos audio systeem Yamaha
- Draadloos audio systeem Eis
- Draadloos audio systeem Envivo
- Draadloos audio systeem Iluv
- Draadloos audio systeem Lenco
- Draadloos audio systeem Linksys
- Draadloos audio systeem Maginon
- Draadloos audio systeem Muse
- Draadloos audio systeem Naim
- Draadloos audio systeem Sonos
- Draadloos audio systeem OXX Digital
Nieuwste handleidingen voor Draadloos audio systeem
4 Oktober 2023
9 September 2023
9 September 2023
28 Augustus 2023
16 Augustus 2023
6 Maart 2023
6 Maart 2023
21 Mei 2023
21 Mei 2023