Alpine S-W8D2 Handleiding

Alpine Subwoofer S-W8D2

Lees hieronder de 📖 handleiding in het Nederlandse voor Alpine S-W8D2 (8 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
R/S-DB8V-TRK Truck Enclosure Installation Manual
Compatible with the following models:
R2-W8D2
S-W8D2
Introduction
Congratulations on purchasing this truck enclosure. This installation manual is designed to take you through the step-
by-step installation of the ‘R’ or ‘S’ Series Dual 8” Subwoofer Vented Enclosure for Trucks. Please familiarize yourself
with the owners manual and if you still have additional questions please contact our support team at 1-800-TECH-
101.
Note: To ensure safe use, Always follow these precautions.
The installation of this product requires specialized skills and experience. We recommend that you have the product
installed by an Alpine authorized dealer.
Before you use this product, be sure to carefully read this installation manual so that you can use the product
correctly, Failing to do so could lead to damaged equipment or an accident. Alpine Electronics bears no responsibility
for problems that arise as a result of failure to follow the instructions in the manual.
Make sure enclosure is secured to the vehicle. Failing to do so can lead to electric shock, injury or damage to
equipment.
When making a hole in the vehicle body, be careful to avoid damaging pipes, the fuel tank, electrical wiring,
and the like. This kind of damage could lead to an accident or fire.
Do not install the product where it may be exposed to water or in a place with high levels of humidity or dust.
Doing so could lead to fire or damaged equipment.
Start all screw threads by hand and avoid overtourqing screws, failure to do so may damage your equipment.
Matching Alpine mono ampliers are sold separately - check with an Alpine authorized dealer.
Recommended Amplifier settings
R-A75M amp S-A60M amp
Gain=1 o’clock position
LP Filter=70Hz
Bass EQ=0 (Off)
Subsonic Filter=30Hz
Gain=1 o’clock position
LP Filter=70Hz
Bass EQ=0 (Off)
(Note: If available with your HU/DSP -
We recommend a Subsonic lter, if possible
with Fc=30Hz @-24dB/Oct.)
Tools Required
Hex Key Driver (2pcs. included) Power Drill with a Low Torque Setting (Optional)
4mm 3mm
Note:
Use Hex Key Drivers for Enclosure feet, Front/Rear brackets and
amp tray: Failure do so could result in damage to the enclosure.
Note:
Power Drill for Subwoofer and Amplifier installation only.
Accessory List
Driver Side Enclosure Passenger Side Enclosure
Front/Rear Link Bracket Front Cover/Trim Bars
Front Rear
Left/Right Amp Tray Bracket Stacking Feet for Enclosure
6 Standard Stacking Feet
(Rubber/Washer/Rubber)
2 Pair Extra Parts
(Rubber/Washer)
1 Installation screws are temporarily installed in both
driver and passenger side enclosures. Remove all
screws to prepare for assembly.
Stacking feet screws
Front bracket screws
Rear bracket screws
Amp bracket screws
Stacking feet screws
Front bracket screws
Driver side Passenger side
2 If applicable, attach inner amp tray brackets using
supplied M5x20mm screws (4pcs.) and M5x20mm
washers (4pcs.).
Note: Amp tray brackets can be trimmed for narrow
applications. Amp tray will not be used in some
applications - See fitment chart. If Amp brackets are
not installed, the 4 mount screws should be left snugly
tightened in both enclosures.
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the amp brackets.
Amp tray brackets
3 Place enclosures upside down on a flat surface
and set to required width. Align rear link bracket
with threaded inserts and secure bracket using
supplied M5x20mm screws (4pcs.) and M5x12mm
washers (4pcs.).
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the rear bracket.
Rear bracket
See Table 1
4 Rotate assembly rightside up and attach front link
bracket using supplied M5x20mm screws (4pcs.)
and M5x20mm washers (4pcs.) as shown.
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the front bracket.
Front bracket
5 Using the supplied M5x60mm screws (6pcs.)
and M5x20mm washers (6pcs.) install feet as
shown. Additional feet spacers are included to
accomodate vehicles with uneven floors, floor
mats etc. - see fitment chart.
Caution: To avoid damage to the enclosure use supplied
Hex Key driver for when installing the enclosure feet.
6 Place mono amplifier on amp tray and mark
the mount holes. Then drill and mount with
appropriate size screws (not included).

Product specificaties

Merk: Alpine
Categorie: Subwoofer
Model: S-W8D2

Heb je hulp nodig?

Als je hulp nodig hebt met Alpine S-W8D2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer Alpine

Alpine

Alpine SS-SB12 Handleiding

16 Augustus 2023
Alpine

Alpine R-W12D2 Handleiding

16 Juni 2023
Alpine

Alpine RS-W12D4 Handleiding

19 Mei 2023
Alpine

Alpine RS-W10D4 Handleiding

30 April 2023
Alpine

Alpine S-W8D4 Handleiding

28 April 2023
Alpine

Alpine PWD-X5 Handleiding

28 April 2023
Alpine

Alpine RS-W10D2 Handleiding

27 April 2023
Alpine

Alpine R2-W8D2 Handleiding

26 April 2023
Alpine

Alpine R-W10D4 Handleiding

24 April 2023
Alpine

Alpine KTE-8G.3 Handleiding

23 April 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

RCF

RCF S 19 Handleiding

10 April 2024
RCF

RCF S 29 Handleiding

10 April 2024
KEF

KEF KC92 Handleiding

6 April 2024
Klipsch

Klipsch Reference Premiere RP-1200SW Handleiding

3 April 2024
Klipsch

Klipsch Reference Premiere RP-1000SW Handleiding

3 April 2024
Velodyne

Velodyne Deep Waves 10 Handleiding

27 Maart 2024
Klipsch

Klipsch PRO-1000SW Handleiding

27 Maart 2024
Totem

Totem KIN Sub Handleiding

27 Maart 2024
Velodyne

Velodyne Deep Waves 12 Handleiding

27 Maart 2024
Kanto

Kanto SUB8V Handleiding

27 Maart 2024