Aktobis WDH-500AH Handleiding
Aktobis
Ontvochtiger
WDH-500AH
Bekijk gratis de handleiding van Aktobis WDH-500AH (10 pagina’s), behorend tot de categorie Ontvochtiger. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 5.0 sterren uit 2 reviews. Heb je een vraag over Aktobis WDH-500AH of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/10
Aktobis AG, Borsigstr. 20 -63110 Rodgau / Germany , D
www.AKTOBIS.de
Email: Info@Aktobis.de
Building Dryer WDH-500AH
Dear Customer,
You have chosen a high-quality product. To ensure that you get a lot of enjoyment from this product, here are a few more tips:
In case of any problems:
We hope that the unit meets your expectations! If, despite the greatest possible care, there should ever be cause for complaint,
please contact us briey, as we are very concerned about your satisfaction and would like to clear up any misunderstanding.
Aktobis AG, Borsigstr. 20 -63110 Rodgau / Germany , D
www.AKTOBIS.de
Email: Info@Aktobis.de
Mounting the castors and the transport handle:
To reduce the volume of a new unit, the transport handle and the castors incl. axle are dismantled.
The following accessories are included for castor assembly:
2 x castors
2 x hubcaps
1 x axle
1 x small parts bag, consisting of:
4 x washers
4 x axle clamps (cotter pins)
The following accessories are included for the transport handle assembly:
1 x transport handle
1 x small parts bag, consisting of:
2 x connecting rail
8 x hexagon socket screws (4 mm)
1 x hexagon spanner (4 mm)
To assemble, place the building dryer on the front (front panel). To protect the
unit, we strongly recommend using a soft base. This can be e.g. a blanket,
towel, polystyrene or similar!
A) Loosen the two axle fastening screws located in the base plate with 10 a
mm spanner (see g. 1 above ).
B) Now insert the axle fastening screws through the axle holes that are at the same height and then screw the screws rmly
back into the base plate of the building dryer using the 10 mm spanner.
C) Insert one axle clamp on each side through the small holes at the level of the outside of the dryer housing and then bend
them up or apart (see Fig. 2 below).
D) Now put washer on the axle from each side - up to the axle clamp. a
E) Now the castors can be attached to the axle on each side.
F) Now put a washer on each side of the axle again - up to the roller.
G) Finally, x the whole thing in place by again inserting axle clamp through the top of the outer axle hole on each side and an
then bending it upwards to secure it.
H) Now put on the hub cap from the outside (put it over the axle clamp).
I) To assemble the transport handle, rst take connecting rail included in the scope of delivery and 2 hexagon socket a
screws. Insert the connecting rail halfway into the open hollow linkage and fasten it with the two hexagon socket screws
(see Fig. below). Repeat this step with the second connecting rail and the two more hexagon socket screws on the other 3
side.
J) Now put the transport handle over the open connecting rail on each side and screw it tight with the four remaining hexagon
socket screws. DONE !
Castor
Axle clamp
Hub cap
Washers
Fig. 2
Fig. 3
Axle clamp
Aktobis AG, Borsigstr. 20 -63110 Rodgau / Germany , D
www.AKTOBIS.de
Email: Info@Aktobis.de
After transport or assembly:
As the unit works with cooling liquid, we ask you to let it stand upright for at least 1 hour before using it for the rst time or after
mounting the castors (transport handle), so that the cooling liquid in the unit can settle again.
During rst operation / hose connection:
If you want to use a hose connection for draining the condensate, make sure that the hose connection is properly seated and
that the condensate (water) can always drain o unhindered! If this is not observed, the water condensed by the building dryer
(up to 50 litres per day) can cause damage to the room!
Room humidity and dehumidication performance:
If you want to check the room humidity and the associated dehumidication performance with your own humidity meter
(hygrometer), please avoid attaching this humidity meter to a wall, as this will falsify the true humidity content of the room air.
See also the explanations under Troubleshooting !!!
Important safety instructions:
- Supervise the building dryer when children are near the unit !
- Watch out for electricity - never walk into or insert objects into the appliance !
- Do not place any objects on the construction dryer !
- Do not block the exhaust and intake louvres of the unit and please ensure sucient space/clearance at and around the fan !
- Make sure that there is sucient air supply to the unit, otherwise it can lead to a reduction in performance and, in the worst
case, to overheating and/or re ! Please always keep a distance of approx. 20 cm to the wall to avoid possible overheating
of the unit ! Do not use in airtight rooms !
- Only qualied personnel or electricians are allowed to open the unit or carry out repairs !
- Make sure that no moisture gets into or onto the unit !
- Only use the recommended voltage for operating the unit !
- Make sure that the power cable is unfolded (untied) before connecting it to the socket !
- Make sure that the plug is cleanly and properly connected to the socket before using the appliance !
- Do not use multiple sockets to operate the building dryer !
- Make sure that highly ammable substances (e.g. gases/oils etc.) are never in the vicinity of the unit !
- Do not use any insect, oil or paint spray etc. near the building dryer. This may cause damage to the unit or even re !
- If you are not going to use the unit for a long time, switch it off and disconnect the mains plug !
- Do not disconnect the mains plug by pulling on the power cable !
- Please keep the unit away from heat sources and avoid direct sunlight !
- Always hold and transport the unit in its proper position ! Never place the unit on its side or even upside down !
- Make sure that the unit is earthed !
Please switch o the unit immediately and disconnect it from the mains/power supply if anything seems to be wrong !!! In this
case, please contact a specialist and do not attempt to repair the unit yourself !!!
Examples: Fan does not run during operation, fuse has blown, there is a funny smell or the compressor rattles loudly.
Important operating and safety instructions regarding the refrigerant R290 in this unit:
(Read these instructions carefully and observe them before using the unit ! )
• The unit operates with the refrigerant R290. This refrigerant is highly ammable and explosive if the safety instructions are
not observed!
• The refrigerant R290 complies with the European environmental directives !
• The unit contains 0.23 kg of refrigerant R290 - the maximum permitted charge of refrigerant R290 for dehumidiers/building
dryers is 0.3 kg !
• The unit should not be stored or operated in a room with burning/heating appliances or open re !
• Protect the unit and especially the parts installed inside from damage or ames/heat !
• Please note that the refrigerant is odourless and therefore a leak cannot be detected immediately by an emerging odour !
• If refrigerant leaks, it may ignite or explode, especially in poorly ventilated rooms in conjunction with high heat, sparks or
ames !
• Make sure that the outlet of the exhaust air is always ensured and not obstructed by other objects !
• Set-up, operation and storage of the unit should take place in a room with a minimum size of 11
m2 !
• Pack the unit carefully when you are no longer using it and protect it from dama ge!
• When cleaning, proceed strictly according to the manufacturer's instructions and do not use any additional heat sources to
possibly accelerate the defrosting process of the appliance !
• Never work on the cooling circuit or parts containing refrigerant yourself !
Product specificaties
| Merk: | Aktobis |
| Categorie: | Ontvochtiger |
| Model: | WDH-500AH |
Heb je hulp nodig?
Als je hulp nodig hebt met Aktobis WDH-500AH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Ontvochtiger Aktobis
20 April 2025
20 April 2025
20 April 2025
16 November 2024
7 Oktober 2024
Handleiding Ontvochtiger
- Euromac
- Frigidaire
- Flama
- JHS
- Nedis
- Qlima
- PureGuardian
- Sencor
- Schimmel-DRY
- Trebs
- Whynter
- Infiniton
- Turmix
- Mission Air
- Air&Me
Nieuwste handleidingen voor Ontvochtiger
15 Juni 2025
15 Juni 2025
14 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025