Akg PZM-10 Handleiding

Bekijk gratis de handleiding van Akg PZM-10 (2 pagina’s), behorend tot de categorie Microfoon. Deze gids werd als nuttig beoordeeld door 53 mensen en kreeg gemiddeld 4.0 sterren uit 9 reviews. Heb je een vraag over Akg PZM-10 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

T

PZM 10 (LL)

he A K G / C r o w n PZM10 is a Pressure

Zone Microphone

® desied for gn

se

cu

rity, surveillance, and conference-

table use.

PRESSUREZONE

MICROPHONE

Sie it ncdoes not lk oolike a microphone, it is

inconspicuous. The mic’s tlar housi ubung

mounts in a 25/32" diameter hole in a ceiling

panel, wall or table.

Like other Pressure Zone Microphones, the

PZ

M1

0 es a miniature mic capsuluse

mounted very near a sound-reflecting plate or

boundary, in the Pressure Zone. In this zone,

d

ir

ect sound from the sound source combines

in ase at all ephfrquencies with reflected

sound o the boundary. The benets are

ma

ny

: 6 dB more sensitivity, 6 dB less noise, a

wide smooth efrquency response ee ofrf

phase interference, excellent clarity and

“

r ,each

”and consistent pickup anywhere

around the mic.

In the M10, low ePZfrquencies below the

vo

ice ra

nge are rolled o to reduce pickup of

air conditiing rumble. The hi-eongh frquency

response is boosted slightly to help articula-

ti

on

.

Be

cause of its tailored response and PZM

constr, the 0 wucontiPZM1ill pick up conver-

sa

ti

on

s or other desired sounds with extra

clarity and definition.

The microphone connector is an XLR te yp

(3-pin pro audio) for easy pl-in itaugnsllation.

The

ou put

t is balanced, low iedampnce, which

a

ll

ow

s long cable rs wunithout hum pickup or

hi-egh frquency loss. Powering is by 12 to

48 V phantom power.

The PZM10 LL has a line level output.

The mic’s humbucking transformer and steel

case prevent hum pickup, even near fluores-

cent lights.

Installation

To pick up speech at a small conference table

(about 6 ft square), mount e 0 ieeonPZM1n

the mile of the table. For longer tables, dduse

on

e

PZ

M in the middle of every 4 to 6 people.

No person should be more than 3 ft om eefr

the nearest microphone.

1. Plse refer to Fig. 2 and identify the paearts

shown.

2.

De

termine ere u want to iwhyonstall the

microphone, and drill a 25/32" diameter hole

Specifications

T

ra

nsducer type:

Electret condenser.

F

re

qu

ency response (typical): 80 Hz to ,000 20

Hz. See Fig. 1.

Polar pattern: Hemispherical.

Iedance: mp240 ohms, balanced. Recom-

me

nd

ed minim load iedamumpnce 1000

ohms.

Open circuit sensitivity:

2.5 mV/Pa* (–52 dB V/). Pa

Power sensitivity: –52 dBm/Pa*

E

qu

ivalent noise level (self-ise): no

26 dB SPL tical (0 dB = 0.0002 dyne/cmyp2),

A-weited. gh

S/N Ratio: 68 dB at 94 dB SPL.

Ma

xim SPL: mu

120 dB SPL produces 3% THD.

Operating volge: ta12 to 48 V phantom power,

pos

iti

ve voltage on pins 2 and 3 with respect

to pin 1.

Po

lity: ar

Positive pressure on the diaphragm

pres a itive age on pin 2 woducposvoltith

re

sp

ect to pin 3 of ouputt connector .

Cu

rre

nt drain: 400 microamperes.

Output connectors:

PZM10:Ma le XLR te (3-pin praypo udio).

PZM10 LL: Line level output,

unterminated cable.

Cable: None supplied. Use 2-conductor shielded

mic cable.

Materials: Stl plate and housi. eeng

Fini: shOff-e. May be painted any whitcolor; take

care to rst seal the ening betwopeen the

capsule and boundary plate.

Net weit: gh2.6 oz. (.6 g). 73

Dimensis: onSee Fig.2.

Fig. 1

Fig. 2

F

re

quency Response

F

re

quency in Hz

there. * 1 pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL.

Product specificaties