Aiwa SB-X350P Handleiding

Aiwa Speaker SB-X350P

Lees hieronder de 📖 handleiding in het Nederlandse voor Aiwa SB-X350P (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

Cannot Power On

Charge the speaker and make sure it has enough battery

SB-X350P

Portable Wireless Stereo Speaker

• Bluetooth 5.0

• Support: A2DPV1.2; AVRCPV1.4 GAVDPV1.2;，

AVDTPV1.2; SPPV1.2; AVCTPV1.2

• Wireless work distance: 10 meters

• Output Power: 2*30W

• v Dri er Unit: tDiame er 102 mm outside mangne 4ohmt , , 35W*2

Diame ert 31 mm inside mangne 8ohm t , , 15W*2

• Frequency response: 60Hz 20KHz-

• Signal-to-noise ratio: ≥80DB

• Battery type: Lithium-ion 7.2V/4000MAH(4*2000mah) ,

• DC input voltage/current: TYPE-C USB 5V/0.5A-2A

• Playtime: 2.5-10 hours (varies by volume level and content)

• Battery charge time: 5-6 hours

• Dimensions: 372*193.3*166mm

• Weight: 3.7 kgs

• Keep the speaker and its accessories away from the reach

of kids as they might cause a choking hazard.

• Keep the speaker away from fire, water, liquids, extreme

heat, and strong magnetic fields.

• Do NOT use this speaker at high volume for extended

periods, as this may cause permanent hearing damage or

loss.

• Do NOT drop or knock the speaker on hard surfaces.

• Do NOT use chemicals or detergents to clean the speaker.

• Do NOT scrape the surface with sharp objects.

• Do NOT make unauthorized alterations to this product.

Li ning ste music om fr external audio s eourc

1.Power on the speaker.

2.Using the AUX Cable (φ3.5mm), connect your external

device to AUX-in port on speaker.

3.It will automatically turn to AUX-in mode, the LED

Indicator turns solid green.

Overvivew of Speaker

Charging

Battery Status

Music Control

BIuetooth connection

• 1 x Speaker

• 1 x Type-C charging Cable

• 1 x AUX Cable (Ф3.5mm)

• 1 x User Manual

Previous Song

Next Song

Light Mode

Play

Modes

Power on/off

Bluetooth LED Indicator

Battery LED Indicator

Pause/Play

Package Includes

2nd white light flashes

3rd white light flashes

Fully charged

Low battery (<20%)

Caution

Troubleshooting

Cannot c non ect with the device

Note: Under AUX-IN mode, skip songs are not workable.

Sound mode

Mode Change Button : O

ut ordo /Indoor

1.Before first time use, fully charge the built-in battery.

2.Connect the Type-C Cable (included) between

the Charging port on the speaker, and

a USB port on a computer or USB AC Adapter.

• Please check the following:

• The Bluetooth device supports A2DP profile

• The Speaker is within 10m from the device.

• The Speaker is in pairing mode, the LED indicator

blinking blue.

Note:

• When power on, the speaker automatically

reconnects to the last mobile device it was connected

to. (The speaker can memorize maximum of 8 paired

devices ).

• The speaker will automatically shut down after 10

minutes in pairing mode if no devices are paired for

power saving.

Make sure that the speaker is within 10 meters from

your mobile device,

1. Press button until hear a rising tone and the

Bluetooth LED Indicator fast blinking blue.

2. Go to the Bluetooth settings on your mobile

device, search and select “AIWA SB-X350P” from the list.

3. Once paired, the LED indicator turns blue.

Note: When the battery charge <5% the speaker will ,

power off automatically.

Power On

Press button until hear a rising tone and the Bluetooth

LED Indicator light on.

Power Off

Press button until hear a descending tone and

the Bluetooth LED Indicator light off. Bluetooth Disconnection

TWS (True Wireless Stereo)

Function

The TWS technology enables you to use two speakers

pairing via Bluetooth to create a wireless dual-channel

system to deliver true stereo sound effect.

TWS connection operation

1. Place the two speakers near each other (the distance

should not be over 10 meters).

2. Power on the two speakers, double click the

button

on one speaker as MASTER speaker (playback left

channel ), the LED indicator fast blinking Blue and gree

then the two speaker will pair to each other

automatically ( The other speaker will be as SLAVE

speaker and playback right channel )

3. Once paired, Master and slave speaker LED indicator

turn solid blue

Disconnect the TWS connection

N do Soun

Poor s aound qu lity

• Make sure the music volume is at audible level on both

your device and speaker.

• Make sure your device is successfully paired with the

speaker, the LED indicator turn solid blue.

Move the device closer to this Speaker or remove any

obstacle between them.

Just simple insert your TF card into the port, the speaker

can automatically turn to TF card reader mode, and play

the MP3 music store in the card.

TF d car rea erd (m cri o SD d)car

Battey LED Indicator

Double click “ ” mode button to change the sound

mode The LED indicator slowly flash blue in outdoor .

mode, and the LED indicator keep solid blue in indoor

mode.

Remark: This speaker's default mode is indoor.under the

USB disk and TF card mod LED is green.,

Volume Down/Volume Up

Charging port

USB card reader TF card reader

AUX input

Reset key

Press“ M ” mode button on one of the speaker until LED

Indicator fast blinking Blue to disconnect the TWS

connection .

Reset the sp :eaker lf the function buttons without

working, disconnect the charging cable, place a small

pin (<3mm) into the reset key and hold it for 2 seconds

until the LED light off.

Click ‘ ’ button to change the LED Lights modes.

1: Musical Pulse (Pulse from bottom to top)

2: Half-circle rotation (rotate with the rhythm of the music)

3: Full-Cyclic rotation (rotation speed is automatically

adjusted with the size of the music)

4: Flash rhythm (brightness flashes with the beats of the

music)

5: Musical Pulse (from the middle to the upper and lower

pulse)

6: Turn off the lights

LED M e lights od

Blinking Red (Sound

Prompts 3 times at 20%,

10%, and power off)

30% charged 1st white light flashes

30%-70% charged

70%-99% charged

3 solid white lights

5 6 7 8 9

Press " M " button until the Bluetooth LED Indicator fast

blinking blue to disconnect the current connected device,

and go into new Bluetooth-paring mode.

Volume UP

Play/Pause

Next track

Previous track

Switch Bluetooth mode/Aux-in mode…………Click M

Click

Rotate the knob Clockwise

click

Volume Down Rotate the knob Counterclockwise

Product specificaties

Merk:	Aiwa
Categorie:	Speaker
Model:	SB-X350P

Heb je hulp nodig?

Als je hulp nodig hebt met Aiwa SB-X350P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker Aiwa

Aiwa KBTUS-450 Handleiding

20 Juli 2023

Aiwa RBTU-600 Handleiding

11 Juni 2023

Aiwa SB-X120 Handleiding

15 Mei 2023

Aiwa BSTU-800 Handleiding

12 Mei 2023

Aiwa RS-X60 Diviner Ace Handleiding

6 Mei 2023

Aiwa MI-X250 Retro Cubic Handleiding

6 Mei 2023

Aiwa Katana X MI-X30 Handleiding

6 Mei 2023

Aiwa MI-X140 Handleiding

2 Mei 2023

Aiwa BS-110 Handleiding

30 April 2023

Aiwa SB-X150 Handleiding

28 April 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

OTTO Bluetooth Revo NC2 Handleiding

20 April 2024

REL Acoustics Strata Handleiding

20 April 2024

REL Acoustics Strata III Handleiding

20 April 2024

Soen Transit Handleiding

18 April 2024

Miller & Kreisel MP300RC Handleiding

18 April 2024

Soen Transit XS Handleiding

18 April 2024

Miller & Kreisel MP7 Handleiding

18 April 2024

Qian QRBT1801 Handleiding

17 April 2024

Focal Twin6 Handleiding

17 April 2024

Kenwood KFC-WPS1000F Handleiding

16 April 2024